Resumen del contenido incluido en la página 1
FP150 Food Processor
I
N
S
T
R
U
C
T
I
O
N
S
MODEL FP150 FOOD PROCESSOR
ML-104600
701 S. RIDGE AVENUE
TROY, OHIO 45374-0001
FORM 33530 Rev. A (3-98)
Resumen del contenido incluido en la página 2
LOCKING SCREW FEEDER/LID WRENCH CUTTING TOOL PUSHER FEED TUBE PUSHER DICING GRID PLATE EJECTOR PUSHER PLATE PLATE SHAFT LOCKING KNOB PL-52142 FP150 Food Processor TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 3
Installation, Operation and Care of MODEL FP150 FOOD PROCESSOR SAVE THESE INSTRUCTIONS FOR FUTURE USE GENERAL The Model FP150 Food Processor is used for slicing, shredding, grating, Julienne cutting and dicing vegetables, fruits or cheese. The compact unit is designed for ease of operation and quick cleaning. A wall rack and a wide range of slicer, shredder, and dicing plates are available options. INSTALLATION UNPACKING Prior to installation, test the electrical service to ensure that it agre
Resumen del contenido incluido en la página 4
Interlock switches prevent the machine from operating when the feed hopper is out of position or the pusher plate is raised above the feed hopper. If these features do not function as described, contact your local Hobart service office. During operation, when the pusher plate is fully raised above the feed hopper, the machine stops and allows the pusher plate to be rotated counterclockwise for loading. To continue operation, rotate the pusher plate clockwise until it is directly above the feed
Resumen del contenido incluido en la página 5
CUTTING TOOL GUIDE 3 Crimping Slicer — /16" (4.5 MM) PL-52135 For ripple slicing of root vegetables. 1 Fine Slicer (2 Blade) — /16" (1.5 MM) 9 For slicing firm or fragile products. Also for use with /32" dicing plate. Makes very PL-52136 thin slices of pepperoni, mushrooms, cabbage, potatoes, cucumbers and radishes. 5 9 1 7 3 Fine Slicer (1 Blade) — /32" (4 MM), /16" (14 MM), /8" (3 MM), /32" (6 MM), /8" (10 MM) Use is same as 2-blade fine slicer. Also slices soft and/or juicy products such a
Resumen del contenido incluido en la página 6
USING THE FEED HOPPER After the pusher plate is raised, prepared products such as potatoes, carrots, onions, lettuce, cabbage, etc., can be placed in the large feed hopper. The feed hopper has one fixed and one detachable partition wall. For highest capacity and best cutting results, the detachable partition wall should be removed only when necessary because of product size. To remove the detachable partition wall, unscrew the two black knobs on the outside of the feed hopper. The fixed parti
Resumen del contenido incluido en la página 7
9. Replace the locking screw. 10. Place the feed hopper on the hinge pins and lower to normal position. Turn and lower the pusher plate. Replace the feed tube pusher. MAINTENANCE WARNING: TURN THE MACHINE OFF AND UNPLUG THE ELECTRICAL CORD BEFORE DOING ANY MAINTENANCE. Routinely inspect the machine to ensure that it is in proper working order. Plates must be clean, intact and sharp. Regularly lubricate the pusher plate shaft with a drop of mineral oil, NOT COOKING OIL. If the machine develo
Resumen del contenido incluido en la página 8
TROUBLESHOOTING FAULT POSSIBLE CAUSE REMEDY Motor won't start. A. Feed hopper not locked in Make sure feed hopper is locked correct position. correctly. B. Pusher plate raised. Turn pusher plate clockwise and lower it. C. Fuse or circuit breaker Have electrician check circuit. interrupting power. Machine stops while operating and A. See B and C above. won't restart. B. Motor is overloaded and motor Allow the motor to cool; motor is too warm. protector will allow restart when it has cooled. Low
