Resumen del contenido incluido en la página 1
GILSJ JN MIXERS
MORTAR-PLASTER MIXER
MODEL: 1200MP
OPERATOR’S GUIDE & PARTS MANUAL
GILSJ JN MIXERS
4343 Easton Road · St. Joseph, MO 64503
BY
816-233-4840 · 800-253-3676
Fax 816-233-4624 · 888-253-3676
E-Mail: cleform@ccp.com
Web Address: www.cleform.com
Resumen del contenido incluido en la página 2
INTRODUCTION This operator’s manual has been prepared to provide the information you need to correctly operated and maintain your mixer. For maximum satisfaction, carefully read and follow the instructions in this manual. Should you need repair parts or service, refer to the parts breakdown on pages 14 through 27. Information regarding operation and maintenance of the factory-installed engine or motor can be found in a separate engine/motor owner’s manual supplied with the mixer. The manual p
Resumen del contenido incluido en la página 3
TABLE OF CONTENTS 1. SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 2. ASSEMBLY AND PREOPERATIONAL CHECKS . . . . . . . 4 3. CONTROLS AND OPERATION Clutch Control Lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Tow Pole Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Safety Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4. MIXER TRANSPORT . . . . . . . . . . . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 4
1 – SAFETY PRECAUTIONS THE FOLLOWING PRECAUTIONS ARE SUGGESTED TO HELP PREVENT ACCIDENTS. A CAREFUL OPERATOR IS THE BEST OPERATOR. MOST ACCIDENTS CAN BE AVOIDED BY OBSERVING CERTAIN PRECAUTIONS. READ AND PRACTICE THE FOLLOWING PRECAUTIONS BEFORE OPERATING THIS EQUIPMENT TO HELP PREVENT ACCIDENTS. EQUIPMENT SHOULD BE OPERATED ONLY BY THOSE WHO ARE RESPONSIBLE AND HAVE BEEN PROPERLY INSTRUCTED. Read all operating and maintenance instruction before operating or servicing the mixer. Test run th
Resumen del contenido incluido en la página 5
Never charge or fill the unit prior to starting the mixing blades as an overload encountered in starting a loaded unit could damage the engine/motor or drive components. Connect safety chains as instructed when towing the mixer. Connect only to correct hitch or coupler. Keep warning, caution and safety instruction labels clean and in good condition. Replace missing, damaged or illegible labels. 2 – ASSEMBLY AND PRE-OPERATIONAL CHECKS The only assembly required on this mixer is the install
Resumen del contenido incluido en la página 6
3 – CONTROLS AND OPERATIONS 1. The mixing paddles feature adjustable rubber wipers and steel backing plates. Paddles are factory preset for appropriate drum wrap clearance. If adjustment is required, proceed as follows: A. Loosen the wiper attaching hardware and move the wiper outward to maintain contact with the drum but without folding over when in operation. B. After adjustment, turn the mixer arms one full turn manually to check clearance and eliminate the possibility of wiper back plates c
Resumen del contenido incluido en la página 7
TOW POLE ASSEMBLY The tow pole assembly is located on the front of the mixer and is used for transport only. For transport, pull the tow pole assembly out, line up the hold and insert the L-shaped pin through holes. When operating the mixer, pull the L-shaped pin out of the hole and push tow pole assembly all the way in. Line up the holes and insert the L-shaped pin through the holes. SAFTEY CHAINS 1. Cross chains under the tow pole when connecting the safety hooks to the tow pole. SEE FIGURE 2
Resumen del contenido incluido en la página 8
4 – MIXER TRANSPORT 1. Secure drum by engaging drum lock. 2. Secure all moveable parts, including the rear housing. 3. Secure tow pole coupler to vehicle and attach safety chains and hooks. (See FIGURE 2, Safety Chains). A. Pintle type couplers require the appropriate tow vehicle coupler retainer. B. Match ball coupler size exactly with hitch ball. 5 – OPERATING THE MIXER STARTING THE MIXER Start the mixer engine/motor. Refer to the engine/motor manual for proper starting procedures. When the
Resumen del contenido incluido en la página 9
LOADING THE MIXER When the mixing blades are rotating, pour the required amount of water into the drum, then add cement, sand and lime. The desired mixing speed is 33 RPM. DISCHARGING THE MIXER Allow the entire mixture to mix for one (1) full minute. DO NOT STOP MIXER FROM ROTATING. Hold the tilt handle and disengage the drum lock. Dump mortar to the side by pulling the tilt lever downward. After the mixture is dumped, return the drum to the operating position and engage drum lock. CLEANING
Resumen del contenido incluido en la página 10
TROUBLE SHOOTING GUIDE FOR MP MIXERS. ENGINE WON’T START: 1. Check for sufficient fuel. 2. Check oil level (some engines have an oil alert, preventing the engine from starting when oil level is low) 3. Was engine choked when starting? 4. Is engine flooded? 5. Check spark plug. (Clean and check gap). 6. If engine still won’t start, take to service center. BELT DRIVEN MODELS: 1. Check condition of belts, replace if necessary. 2. Check for oil or grease on belts as well as for loose belts. 3. Adjus
Resumen del contenido incluido en la página 11
6 – OPERATING GUIDELINES MASONRY CONSTRUCTION GUIDELINES The strength and durability of brick masonry depends upon the quality of the brick, the quality of the mortar and the workmanship in laying. The strength also depends upon adequate bond and the shape of the masonry unit. Brick quality – Characteristics are hardness and density. Brick for masonry which is exposed to weather or where strength is desired should have a crushing strength of not less than 2500 PSI. Laying and bonding – Brick s
Resumen del contenido incluido en la página 12
7 – LUBRICATION DRUM SEAL HOUSINGS Drum seals are provided on each end of the drum where the mixing shaft passes through to the bearings. It is important to pump grease into the housings through use to retain seal efficiency. Use enough grease to flush out old grease and carry away any grit. Use lithium based grade 2 multi-purpose grease. SEE FIGURE 3 MIXING SHAFT BEARINGS The mixing shaft bearings are permanently factory sealed and lubricated, and should not require further service. WHEEL B
Resumen del contenido incluido en la página 13
DRUM SHAFT BEARING HANGERS Drum yoke bearing hangers are located on each side of the drum, and are equipped with grease fittings. These bearings should be lubricated once each week with lithium based grade 2 multi-purpose grease. ENGINE/MOTOR Refer to the engine/motor operating instructions for all maintenance and lubrication instructions and requirements. JACK SHAFT BEARINGS Pillow block style bearing are used on the drive train counter-shaft. See Drum Seal Housing, Lubrication Guidelines for
Resumen del contenido incluido en la página 14
ENGINE/MOTOR DRIVE SEE FIGURE 4. 1. Align pulleys correctly 2. Tighten locking collars in the direction of rotation and tighten setscrews. 3. Adjust tension on the engine belt as follows: A. Place clutch lever in the engaged (drive) position. B. Move the engine/motor to tighten the belt until the engine plate is slightly above the horizontal position (about 1-2 degrees). Tighten engine/motor securely. 4. Adjust belt fingers so they do not touch the belt when the drive is engaged, but must allow
Resumen del contenido incluido en la página 15
14
Resumen del contenido incluido en la página 16
Concrete Mixer Parts List REF NO. PART NO. DESCRIPTION QTY DRUM & DRIVE 1 232444 Bearing Hanger 2 2 1031 Grease Fitting 4 3 232478 Gear (Gasoline Powered Models) 1 245498 Gear (Electric Powered Models) 1 4 245466 Drum Shell Assembly 1 5 245459 Grill Assembly 1 6 232459 Bearing Support Assembly 2 7 5126 Drum Tilt Lever 1 8 232465 Drum Seal 2 9 5095 Seal Housing 2 10 5097 Seal Retainer 2 11 232573 Shaft Seal 2 12 232462 Bearing, Drum Shaft (comes w/232463) 2 13 245477 Drum Shaft 1 14 232463 Locki
Resumen del contenido incluido en la página 17
16
Resumen del contenido incluido en la página 18
Concrete Mixer Parts List MIXING BLADES REF NO. PART NO. DESCRIPTION QTY 1 245460 Mixing Arm Assembly, Engine End 2 2 245463 Mixing Arm Assembly, Tow End 2 3 245461 Mixing Arm Cap 4 4 5585 Drum Wrap Wiper 4 5 5643 Wrap Wiper Backing Plate 4 6 5088 End Wiper Backing Plate 2 7 5089 Drum End Wiper 2 8 *71195 Capscrew, Hex HD 5/8-11 x 2 Gr 5 10 9 *70249 Capscrew, Hex HD 3/8-16 x 1 1/2 Gr 5 16 10 *70567 Nut, Hex 5/8-11 10 11 *70553 Nut, Hex 3/8-16 20 12 *70657 Washer, 5/8 Spring Lock 10 13 *70649 Wa
Resumen del contenido incluido en la página 19
18
Resumen del contenido incluido en la página 20
Concrete Mixer Parts List ENGINE HOUSING AND AXLE REF NO. PART NO. DESCRIPTION QTY 1 245471 Engine Housing Assembly w/decals 1 2 245470 Housing Base Assembly 1 3 32082 Reflector 2 4 232623 T-Handle Latch 2 5 5402 Handle, Engine Housing 1 6 220521 Rivet, Handle 4 7 223590 Rubber Bumper 4 8 232614 Housing Base Front Plate 1 9 213297 Screw, Thread Forming 5/16-18 x 1/2 6 10 *29065 Screw, Sheet Metal #10-24 x 3/8 4 11 232489 Axle Assembly 1 12 38565 Hub Assembly (includes:) 2 13 1046 Bearing Cup
