Manual de instrucciones de Amana MVH220W

Resumen del contenido incluido en la página 1

Over the Range
Microwave Oven
Installation Instructions
MWT4461D
MWT4461WW
MVH120E
MVH220E
MVH220W
MVH320E
MVH320L
MVH320W
Read all instructions before starting
installation.
Important--Save these instructions for
electrical inspector's use.

Resumen del contenido incluido en la página 2

Installation Requirements Mounting Space Important Safety Instructions This over-the-range microwave oven requires wall Recognize this symbol as a SAFETY mounting space, as shown below. • Minimum of 30 inches between cabinets is required for message installation. If space between cabinets is greater Caution than 30 inches, filler panel kit may be used to fill in gap between microwave oven and cabinets. Contact To avoid electrical shock hazard remove dealer to purchase filler panel kit. house

Resumen del contenido incluido en la página 3

Materials Needed (Not Supplied) Hood Exhaust Duct Outside ventilation requires hood exhaust duct. Use only • Phillips screwdriver metal duct. Read the following carefully. • Pencil • Ruler or tape measure and straight edge Exhaust Connection: Hood exhaust has been designed • Protective gloves to mate with standard 3 1/4 inch x 10 inch rectangular duct. • Carpenter square (optional) If round duct is required, rectangular-to-round transition • Tin snips (in some applications) adaptor must be use

Resumen del contenido incluido en la página 4

Installation Instructions A. Removing Mounting Plate Outside Top Exhaust (Vertical Duct) 1. Place protective blanket on work surface to 1. Slide exhaust adaptor to one side, squeeze sides and protect outer case of microwave oven. Place remove. Save damper and exhaust adaptor. microwave oven on control panel side. 2. Proceed to "Preparing Top Cabinet". 2. Remove 2 screws from mounting plate, as Outside Back Exhaust (Horizontal Duct) shown above. Plate will be used as rear wall 1. Slide exhaust

Resumen del contenido incluido en la página 5

5. Carefully pull out blower unit. Wires extend far 9. Fit exhaust adaptor into house duct. Be sure damper enough to allow for blower adjustments. hinge is on top and damper swings free into wall 6. Turn blower unit end-over-end. Roll blower unit so outlet. fan blade openings are facing out back of microwave oven. Blower unit exhaust openings should match exhaust openings on rear of microwave oven. Wires should be routed in front of motor fan. 10. Remove paper from sticky side of 28 inch fo

Resumen del contenido incluido en la página 6

8. Replace blower plate using 5 screws. 5. Carefully pull out blower unit. Wires extend far enough to allow blower adjustments. 6. Roll blower unit so blades face towards front of microwave oven. Wires should be routed in front of motor frame. 9. Remove 2 screws on front of grille. Remove grille. 10. Install charcoal filter. (Contact dealer to purchase charcoal filter kit). 11. Replace grille and 2 screws. 12. Proceed to "Preparing Top Cabinet". 7. Guide wires into duct while placing blower u

Resumen del contenido incluido en la página 7

1. Find studs, using one of following methods: 7. Drill holes through circles. Diameter of holes should be 5/8 inch for toggle bolts and 3/16 inch for wood • Stud finder--magnetic device which locates nails. screws on studs. Use at least 1 wood screw in stud, • Use hammer to tap lightly across mounting surface and 2 toggle bolt assemblies into drywall or plaster. to find solid sound. This will indicate stud 8. Attach mounting plate to wall. location. 9. Remove toggle assembly from screws. I

Resumen del contenido incluido en la página 8

6. Use rectangular washer to mark hole for drilling in left F. Mounting Microwave Oven side rectangular slot. Place washer in slot by 1. Locate grease filters packed separately and set aside. grasping "ears" on washer to center in opening. Mark Thread power cord through hole, or slot, in bottom of location of hole on rear wall with pencil. Center top cabinet. Keep cord tight throughout step 2. carefully to assure good fit. 2. Install microwave by sliding onto arms of mounting 7. Drill small

Resumen del contenido incluido en la página 9

9

Resumen del contenido incluido en la página 10

10

Resumen del contenido incluido en la página 11

11

Resumen del contenido incluido en la página 12

© 1994 Amana Refrigeration, Inc. Part No. C8935506 Amana, Iowa 52204 Printed in U.S.A.