Resumen del contenido incluido en la página 1
IVlodels/lViodelos
INSTRUCTIONS
p
721.80402
721.80403
721.80404
721.80409
721.80522
721.80523
721.80524
721.80529
0
i=.
Read and save these _rowave Hood Combination
installation instructions.
Combinaci6n Microondas Campana
Lea y guarde estas
instrucciones de
instalaci6n
Part No. 3828W5U0437 Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U.S.A www.sears.com.
Resumen del contenido incluido en la página 2
YOUR SAFETY FIRST BEFORE YOU START • Proper installation is the installer's responsibility! - Read the entire manual before you begin. - The model number label is located on the oven front. See Figure 1. - Mounting plate is located on back side of microwave oven. See Figure 2. BE SURE TO READ THE FOLLOWING SAFETY iNSTRUCTiONS: Model Number Label Mounting Plate m :::::::::::::::::::::::::::::::::::::::: Z r-' m Z Back of oven Figure 1 Figure 2 _k WARNING _k FOR YOUR SAFETY: • You will need TWO pe
Resumen del contenido incluido en la página 3
YOUR SAFETY FIRST • THIS APPLIANCE MUST BE GROUNDED! - If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. PROPERLY POLARIZED AND • Place the plug into a properly installed and grounded GROUNDED OUTLET outlet. See Figure 3. • Do not use an extension cord. • Keep the power cord dry and do not pinch or crush it. • DO NOT, UN
Resumen del contenido incluido en la página 4
YOUR SAFETY FIRST • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT. - Mount the oven against a flat, vertical wall, so that it is supported by the wall. The wall should be constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath. - ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, 2" x 4" wall stud. - DO NOT mount the microwave oven to an island or peninsula cabinet. - BE SURE the upper cabinet and rear wall structures are able to support 150 Ib
Resumen del contenido incluido en la página 5
PARTS, TOOLS, MATERIALS THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN: NOTE: Depending on your ventilation requirements, you may not use all of these parts. Damper/duct connector One power cord clamp and (for roof vented or wall vented installation) One dark-colored mounting screw Not Actual Size (to hold the power cord) Actual Size One power cord clamp bushing - Actual Size (for the cord hole in a metal upper cabinet) Four 1/4" x 2" lag screws - Actual Size Four 1/4" x 3" toggle bolts - Actual
Resumen del contenido incluido en la página 6
PARTS, TOOLS, MATERIALS YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION: Carton or other heaw material for covering the counter top. Stud Finder or Thin Nail Clear Tape (for taping the templates to the wall) Keyhole Saw (for the power cord hole) Saber Saw (for cutting vent holes for roof or wall vending) 0I Electric drill Phillips Screwdriver (for the screws) 3/8" and 3/4" wood drill bits c':'_-" Pencil 1/2" and 3/16" drill bits Plumb Line Flat Blade Screwdriver (for the tog
Resumen del contenido incluido en la página 7
STEP 1: PREPARE THE ELECTRICAL CONNECTIONS _k WARNING _k AVOID ELECTRICAL SHOCK! THIS APPLIANCE MUST BE GROUNDED! 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 4 Detail. Upper Cabinet NOTE: The outlet should be on a circuit dedicated to the microwave oven 120V, 60Hz., AC only, with a 20ampere fused electrical supply. IMPORTANT: If you do not have the proper wall outlet, i_i__Grounded Outlet you MUST have one installed by a qualified electr
Resumen del contenido incluido en la página 8
STEP 2: PREPARE THE VENTING S YSYTEM NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 9, page 9. WARNING - FIRE HAZARD THIS OVEN MUST BE PROPERLY VENTED! J You may vent your oven in one of three ways: Roof Venting If your oven is located on an outside wall near the roof, as in Figure 6 (3-1/4" x 10" duct) and Figure 8 (6" round duct.) Wall Venting If your oven is located on an outside wall on the fir
Resumen del contenido incluido en la página 9
STEP 2: PREPARE THE VENTING S YSYTEM STANDARD FITTINGS NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper sticking. DUCT LENGTH The total length of the duct system, including straight duct, elbows, transitions, wall or roof caps must not exceed the equivalent of 140 feet. For best performance, do not use more than three 90 degree elbows. Below ar
Resumen del contenido incluido en la página 10
STEP 3: PREPARE THE VENTING BLOWER Your microwave oven is shipped with the blower assembled for room venting (recirculating). You need to adjust the blower if you want wall vented or roof vented installation. A. WARNING _k ELECTRICAL SHOCK HAZARD! UNPLUG UNIT BEFORE WORKING ON IT. • DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result in electrical shock. REMOVE THE MOUNTING PLATE: 1. Remove any shipping materials and parts from inside the microwave ove
Resumen del contenido incluido en la página 11
STEP 3: PREPARE THE VENTING BLOWER WALL VENTED INSTALLATION: 1. Remove two blower unit mounting screws and one or two blower plate screws. Remove the blower back plate blower unit plate from cabinet. See Figure 12. blower plate 2. Carefully lift the blower unit out of the microwave mounting screws oven. Disconnect the blower wire from connector. See Figure 13. 3. Use side cutters or tin snips to cut and remove Knockouts "B" knockouts "B" from Back plate. Discard blower plate knockouts. Be carefu
Resumen del contenido incluido en la página 12
STEP 3: PREPARE THE VENTING BLOWER ROOF VENTED INSTALLATION: blower plate 1. Remove two blower unit mounting screws and mounting one or two blower plate mounting screws. Remove the screws blower plate from cabinet. See Figure 18. 2. Carefully lift the blower unit out of the microwave oven. blower plate bl, 3. Rotate blower unit 90° so the exhaust ports mounting screws face the top of the cabinet. See Figure 19. Figure 18 4. Place blower unit back into microwave oven. 5. Use side cutters or tin s
Resumen del contenido incluido en la página 13
STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION MEASURE AND TACK / TAPE UP THE TEMPLATE 1. Using a plumb line and (metal) measuring tape, find and mark the vertical center line (_ on the back wall, as in Figure 22. O 2. Find and mark one or two points where the studs are on the wall (Studs are normally 16 inches apart.) i and then measure and mark the stud locations. If I you cannot find any wall stud, consult a local I building contractor. I I Zk CAUTION A, m i DO NOT ATTEMPT TO INS
Resumen del contenido incluido en la página 14
STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION DRILL THE HOLES IN THE WALL AND UPPER CABINET. A, WARNING _, BE VERY CAREFUL WHEN DRILLING HOLES INTO THE WALL. Electrical wires could be concealed behind the wall covering and if the drill hits them you could get an electric shock. 1. Find the points on the mounting plate labeled "A", "B", "C" and "D". Drill a 3/16" diameter hole at any of these points that are in front of a wall stud. Drill a 3/4" diameter hole at any of these points
Resumen del contenido incluido en la página 15
STEP 5: INSTALL THE MOUNTING PLATE TO THE WALL THE OVEN MUST BE CONNECTED 3/16" Hole on Studs TO AT LEAST ONE WALL STUD. 3/,_" Hole on Drywall Only 1. Draw a vertical line on the wall at the center of the [ Minimum 66" I For Wall_- 30" wide space. Use the mounting plate as the template for the L ven,.o,. rear wall. Place the mounting plate on the wall, making sure that the tabs are against the bottom of the cabinet. Line up the notch and center line on the mounting plate to the center line on th
Resumen del contenido incluido en la página 16
STEP 5: INSTALL THE MOUNTING PLATE TO THE WALL TO PREPARE THE REAR WALL CUTOUT OPENING AND EXHAUST ADAPTOR/MOUNTING PLATE FOR WALL VENTING AND ROOF VENTING: NOTE: If room vented installation is used, skip this step. t 1. Place the mounting plate against the rear wall as described in step 5 item 1 (page 15). REARWALLTEMPLATE 2. Use the wall template to determine the location and size of the box cutout for the rear wall duct. See Figure 28 Figure 28. • Attach the exhaust adaptor to the rear mounti
Resumen del contenido incluido en la página 17
STEP 6: ATTACH THE OVEN TO THE WALL _k WARNING A, II You will need two people to lift this power cord microwave. Failure to use more than one person could result in personal injury. hole 1. Carefully lift microwave oven and hang it on support tabs (See Figure 26) at the bottom of the mounting plate. Reaching through upper cabinet, thread power supply cord through the power supply cord hole in the bottom of the upper cabinet. m See Figure 30. Figure 30 2. Rotate the microwave oven upward so the t
Resumen del contenido incluido en la página 18
STEP 6: ATTACH THE OVEN TO THE WALL 5. Roof vented installation: See Figure 32. Install ductwork through the vent opening in the upper cabinet. Complete the venting system through the roof according to the method needed. See "PREPARE THE VENTING SYSTEM," STEP 2 on the page 8. Use caulking to seal exterior roof opening around the exhaust cap. See Figure 6 on page 8. Use power supply cord clamp to bundle the power supply cord. Install the power supply cord clamp, f lit-- using a screw as shown in
