Manual de instrucciones de Icom 200

Manual de instrucciones del aparato Icom 200

Aparato: Icom 200
Categoría: Radio marítima
Fabricante: Icom
Tamaño: 1.2 MB
Fecha de añadido: 3/19/2014
Número de páginas: 55
Imprimir el manual

Descargar

¿Cómo se utiliza?

Nuestro propósito es proporcionarte el acceso más rápido posible a los contenidos incluidos en los manuales de instrucciones del aparato Icom 200. Utilizando la vista previa online, puedes ver rápidamente el índice de contenidos y pasar a la página donde encontrarás la solución a tu problema con Icom 200.

Para tu comodidad

Si ver los manuales de instrucción de Icom 200 directamente en esta página no es cómodo para ti, puedes utilizar dos soluciones posibles:

  • Vista en pantalla completa – Para ver cómodamente los manuales de instrucciones (sin descargarlos en tu ordenador) puedes utilizar el modo de vista en pantalla completa. Para activar la vista del manual Icom 200 en pantalla completa, utiliza el botón Pantalla completa
  • Descargar al ordenador – también puedes descargar el manual de instrucciones de Icom 200 a tu ordenador y guardarlo en tu colección. Sin embargo, si no quieres ocupar espacio en tu dispositivo, siempre podrás descargarlo de ManualsBase.
Icom 200 Manual de instrucciones - Online PDF
Advertisement
« Page 1 of 55 »
Advertisement
Versión impresa

Muchas personas prefieren no leer el documento en la pantalla, sino en versión impresa. La opción de impresión también está prevista y puedes utilizarla haciendo clic en el enlace más arriba - Imprimir el manual. No tienes que imprimir el manual completo de Icom 200, solo las páginas que elijas. Ahorra papel.

Resúmenes

A continuación encontrarás resúmenes de los contenidos incluidos en las páginas posteriores del manual de instrucciones para Icom 200. Puedes utilizarlos si quieres ver rápidamente el contenido que se encuentra en la siguientes páginas del manual.

Resúmenes de contenidos
Resumen del contenido incluido en la página 1


®
ICOM 200/201/241

Resumen del contenido incluido en la página 2

Resumen del contenido incluido en la página 3

About this manual 1 ICOM-200 / 201 2 ICOM-241 3 Advice and support 4 Register 5

Resumen del contenido incluido en la página 4

Copyright © by Wilke Technology GmbH Krefelder Str. 147 52070 Aachen / Germany manual version 1.4 This manual, together with the hardware and software which it describes, is copyrighted and may not be in any way copied, translated or redered in any other form without the express written consent of Wilke Technology GmbH. Note The editors, translators and authors of this publication have taken great care with the texts, illustrations and programs. Nevertheless, errors cannot be complet

Resumen del contenido incluido en la página 5

Contents Contents 1 About this manual 1-1 Typographic conventions and symbols 1-2 2 ICOM-200 / 201 2-1 Versions 2-1 Differences between ICOM-200 and ICOM-201 2-1 First steps 2-2 Power supply 2-2 PC mode 2-2 RUN mode 2-3 Program download 2-3 SLEEP mode 2-4 Keyboard 2-6 LC display 2-8 Serial Interface 2-9 RS232 2-9 RS485 2-10 Opto inputs 2-11 Power outputs 2-13 Analog inputs 2-15 Analog inputs 2-15 Configuration 0...5V 2-16 Configuration 0…10V 2-17 Configuration 0...20mA 2

Resumen del contenido incluido en la página 6

Contents Opto inputs 3-4 Power outputs 3-6 Serial interface 3-7 RS232 3-7 RS 485 3-8 Analog inputs 3-11 Pin layout 25-pin D-Sub connector 3-14 Technical data 3-15 ICOM 241 – 24V 3-16 Connection to PC 3-17 Technical data 3-17 4 Hints and help 4-1 ® BASIC-Tiger Service Hotline: 4-1 5 Register 5-1 . ii Wilke Technology GmbH • 0241 / 918 900 • http://www.wilke.de/ • support@wilke.de

Resumen del contenido incluido en la página 7

General 1 About this manual 1 This manual does introduce you into the control of the ICOM industry computer family for a fast and easy use. The ICOM industry computer family combines the performance of ® BASIC/TINY-Tiger Computers with steadily needed I/O peripherals in an elegant aluminum chassis. For programming the ICOM industry ® computers a BASIC-Tiger development system is needed. This manual only describes the usage of the ICOM industry computers. ® You can read about the pr

Resumen del contenido incluido en la página 8

ICOM-manual 1 Typographic conventions and symbols Following fonts and symbols are used for fast identification of important informations: Element Meaning KEY Key description, e.g. RETURN ® Program listing Tiger-BASIC program listing ® Instruction Tiger-BASIC instruction Variable Variables or constants you have to enter according to your application. [ ] Elements which can be entered optional. Important remark: Please note! ! Tipps and hints simplifying your work. Tip 1-2

Resumen del contenido incluido en la página 9

ICOM-200 / 201 2 ICOM-200 / 201 Versions This manual describes the ICOM200 and ICOM201 til version V1.3. Newer 2 versions are described in separate data sheets. At ICOM versions V1.4 or newer, the version number is printed on the right hand side of the device. Differences between ICOM-200 and ICOM-201 The ICOM-201 is a special version of the ICOM-200. The following decription shows where the differences between the ICOM-200 and ICOM-201 are. Feature ICOM-200 ICOM 201 Graphic LCD •

Resumen del contenido incluido en la página 10

ICOM-manual First steps Power supply The ICOM-200/201 uses a power supply with 8-12 VDC, 1A. Minus is placed on the pin of the power supply connector. The current consumption is, depending on the application, up to 400mA. 2 PC mode ® After a reset or power-down the Tiny-Tiger inside the ICOM-200/201 is testing if the PC mode pin is „low“. In this case, the ICOM switches to PC mode/Debug mode. Is the pin „high“, the ICOM starts in run mode. The time between power-on and first activit

Resumen del contenido incluido en la página 11

ICOM-200 / 201 RUN mode If the DIP-switch “PC/Run” is in position “Run”, the program in the ICOM- 200/201 is executed immediately after a reset. Debugging is not possible in this mode. Program download 2 A program created with the Tiger software is downloaded into ICOM-200/201 through the 9-pin Sub-D connector. To download the following has to be done: Connect a power supply 8-12 V DC (Polarity: Inner contact = minus, outer contact = plus) Connect ICOM-200/201 and PC with 9-pin D

Resumen del contenido incluido en la página 12

ICOM-manual SLEEP mode ® The ICOM-200/201 can be put into sleep mode if the Tiny-Tiger inside has a real time clock. In sleep mode the power consumption of the ICOM-200/201 is descreased significantly to just approx. 25mA. While in sleep mode, no BASIC program is executed by the ICOM-200/201. 2 Sleep circuit ® The internal clock and SRAM of the Tiny-Tiger are buffered through a Goldcap. The power consumption of clock and SRAM is approx. 70µA, with a fully loaded Goldcap this is enough

Resumen del contenido incluido en la página 13

ICOM-200 / 201 2 ® To put the ICOM-200/201 into sleep mode, the alarm time for the Tiny-Tiger clock has to be set. Following that the ICOM-200/201 falls into sleep mode and wakes up again at alarm time. More detailled information on how to set ® the alarm time can be found in the BASIC-Tiger „Device driver“ manual. If jumper J9 has been drawn and the Goldcap is unloaded, it takes about 30 seconds from connecting the power supply before the ICOM-200/201 switches on. Wilke Technolo

Resumen del contenido incluido en la página 14

ICOM-manual Keyboard The ICOM-200 has a 20 key matrix keyboard. The keyboard is devided into two blocks. The first block has four vertically arranged keys placed directly on the right side of the LC display. Those keys can e.g. be assigned to a menu on the LC display. The second block consists of 16 labeled keys. 2 Reading the keyboard is done with the device driver „LCD1.TDD“. The following example scans the keyboard and gives back a numeric code for the pressed key. Additionally a cha

Resumen del contenido incluido en la página 15

ICOM-200 / 201 '-------------------------------------------------------------------- '----- ICOM_KEYB.TIG '-------------------------------------------------------------------- #define keyb 20 ' keyboard device nummer #include define_a.inc user_var_strict TASK Main 2 word x,n,i string a$ user_eport lastladr,10h user_eport physoffs, 0f0h Dir_port 8,0 INSTALL DEVICE #lcd,"LCD2.TDD",0,0,0EEH,1,150,11H' LCD-1=128x64, 150 KB/s Install device #keyb, "LCD1.tdd", 0, 0,

Resumen del contenido incluido en la página 16

ICOM-manual LC display The ICOM-200 has a graphic LC display with a resolution of 128 x 64 pixel. There’s a special device driver to control this display. By using this device driver it is possible to control the LC display with simple BASIC commands. Detailled information about usage of this device driver „LCD-6963.TDD“ is part ® 2 of the „Device driver“ manual of the BASIC-Tiger . The LC display has LED backlight. The backlight’s power consumption is approx. 250mA. Power supply is 5V

Resumen del contenido incluido en la página 17

ICOM-200 / 201 Serial Interface As a standard the ICOM-200 and ICOM-201 have two serial interfaces. From these the port Ser0 can by choice be configured as RS232 or RS485 interface. The port Ser1 always is a RS232 interface. In PC mode this port is used for downloading the program into the ICOM 200/201. In Run mode it can be used as a usual RS232 interface. 2 Detailled information about the serial interfaces can be read after in the ® BASIC-Tiger „Device driver“ manual. RS232 Seria

Resumen del contenido incluido en la página 18

ICOM-manual The pins of serial port 0 are located on the DB-37 connector: RS232 DB-37 TXD0 (Output) 16 RXD0 (Input) 17 RTS0 36 2 CTS0 35 RS485 The configuration of port 0 as RS485 interface is done by removing the IC3 (MAX232) and placing the IC12 (SN75176) into the 8-channel DIL socket. The DIP switch on the left side plate of the ICOM-200/201 has to be set to RS485. Removing or placing the ICs is only allowed without power supply. Never place both ICs at the same time, this could

Resumen del contenido incluido en la página 19

ICOM-200 / 201 Opto inputs The ICOM-200/201 has eight optocoupler inputs suited for an input voltage range of 5...12 VDC. To use higher input voltages, as 24V for example, an additional serial resistor in the input line is used. The resistor value is selected in accordance to 4...50mA input current needed for the logical “1” level. 2 The internal resistance is 680 Ohm / 0,25 W. If now another input voltage is needed, the totally required resistance can be calculated with the following

Resumen del contenido incluido en la página 20

ICOM-manual '-------------------------------------------------------------------- '----- ICOM200_OPTOIN.TIG '-------------------------------------------------------------------- #include define_a.inc user_var_strict TASK Main BYTE wert 2 USER_EPORT lastladr,10h USER_EPORT physoffs, 0f0h DIR_PORT 8,0 DIR_PORT 7,0 INSTALL_DEVICE #lcd,"LCD2.TDD",0,0,0EEH,1,150,11H' LCD-1=128x64,150 KB/s OUT 8,11111111b,11011111b ' set CTRL-Pins of T6963C OUT 8,10000000b,255


Manuales de instrucciones similares
# Manual de instrucciones Categoría Descargar
1 Icom 201 Manual de instrucciones Radio marítima 15
2 Icom IC-2800H Manual de instrucciones Radio marítima 128
3 Icom 241 Manual de instrucciones Radio marítima 14
4 Icom IC-460 Manual de instrucciones Radio marítima 12
5 Icom IC-7000 Manual de instrucciones Radio marítima 193
6 Icom IC-2200H Manual de instrucciones Radio marítima 634
7 Icom IC-F14/S Manual de instrucciones Radio marítima 34
8 Icom IC-756 Manual de instrucciones Radio marítima 224
9 Icom IC-F1810 Manual de instrucciones Radio marítima 8
10 Icom IC-F1710 Manual de instrucciones Radio marítima 6
11 Icom IC-F110 Manual de instrucciones Radio marítima 118
12 Icom IC-F210 Manual de instrucciones Radio marítima 57
13 Icom IC-208H Manual de instrucciones Radio marítima 201
14 Icom IC-450 Manual de instrucciones Radio marítima 6
15 Icom IC-F24/S Manual de instrucciones Radio marítima 24
16 Acu-Rite #01088 Manual de instrucciones Radio marítima 0
17 Acu-Rite 02010CDI Manual de instrucciones Radio marítima 2
18 Acu-Rite 972 Manual de instrucciones Radio marítima 0
19 Acu-Rite #02036WB Manual de instrucciones Radio marítima 6
20 Acu-Rite 01502BPDI Manual de instrucciones Radio marítima 0