Resumen del contenido incluido en la página 1
®
BUSH HOG
EFM 480/600
Economy Finishing Mower
Operator’s Manual
OPERATION l l MAINTENANCE
04/09 Rev.1 $4.00 50024642
Resumen del contenido incluido en la página 2
CONGRATULATIONS! You have invested in the best implement of its type on the market today. The care you give your Bush Hog implement will greatly determine your satisfaction with its performance and its service life. We urge a careful study of this manual to provide you with a thorough understanding of your new implement before operating, as well as suggestions for operation and maintenance. If your manual should become lost or destroyed, Bush Hog will be glad to provide you with a new copy. Orde
Resumen del contenido incluido en la página 3
EFM 480/600 Operator’s Manual TABLE OF CONTENTS SECTION/PARA PAGE SECTION/PARA PAGE Warranty . . . . . . . . . . . . . . . . . . . . . . . . . .2 IV MAINTENANCE . . . . . . . . . . . . . . . . . . . .11 Dealer Preparation Check List . . . . . . . . .3 4-1 Maintenance Check List . . . . . . . . . .11 Safety Precautions . . . . . . . . . . . . . . . . . .4 4-2 Lubrication . . . . . . . . . . . . . . . . . . . . .11 Federal Laws and Regulations . . . . . . . . .6 4-3 Belt Adjustment . . . . . . . .
Resumen del contenido incluido en la página 4
LIMITED WARRANTY OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state and municipalities’ use and ninety (90) days for commercial use from date of retail sale. Model EFM gearboxes are covered by a five (5) year limited warranty period. The obligation of Bush Hog to the purchas
Resumen del contenido incluido en la página 5
DEALER PREPARATION CHECK LIST EFM 480/600 Finishing Mowers BEFORE DELIVERING MACHINE — The following check list should be completed. Use the Operator’s Manual as a guide. r 1. Assembled completed. r 2. Gearboxes filled with oil. r 3. All fittings lubricated. r 4. All shields in place and in good condition. r 5. All fasteners torqued to specifications given in Torque Chart r 6. All decals in place and readable. (See decal page.) r 7. Overall condition good (i.e. paint, welds) r 8. Operators manua
Resumen del contenido incluido en la página 6
Safety Alert Symbol This Safety Alert Symbol means: “ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” This symbol is used to call attention to safety pre- cautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precau- tions could result in death or serious bodily injury. Safety Signs Signal Words The signal words DANGER, WARNING, AND CAUTION are used on the equi
Resumen del contenido incluido en la página 7
IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safety precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that fol- lows and heed its advice. Failure to comply with safety precautions could result in death or serious bodily injury. In addition to the design and configuration of equipment, hazard control and accident prevention are depen- dent upon the awareness, concern, prudence and proper training o
Resumen del contenido incluido en la página 8
IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such). U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA This Act Seeks: “...to assure so far as possible every working man and woman in the nation safe and health
Resumen del contenido incluido en la página 9
SECTION I INTRODUCTION AND DESCRIPTION ting it. The four caster wheel arrangement, along 1-1 INTRODUCTION with the floating lift linkage and optional front mount- We are pleased to have you as a Bush Hog cus- ed roller, all work together to give an even cut and tomer. Your EFM Series Rotary Cutter has been minimize scalping. carefully designed to give maximum service with minimum down time.This manual is provided to give Power from the tractor is transmitted through a trian- you the necessary o
Resumen del contenido incluido en la página 10
SECTION II PREPARATION FOR USE 2-1 ATTACHING TO TRACTOR NOTE Due to the many variations in trac- tor/implement hitch points and corre- WARNING sponding differences in distances between NEVER STAND BETWEEN TRACTOR tractor PTO shafts and implement input AND CUTTER WHILE TRACTOR IS shafts, drivelines may need to be short- BEING BACKED TO HITCH. ened as described in the following steps: WARNING B. Raise and lower cutter to determine position ADDITIONAL TRACTOR FRONT with shortest distance between t
Resumen del contenido incluido en la página 11
G. Clamp end of driveline in a vice. Cut off shield Figure 2-5 where marked. (Figure 2-3). Figure 2-3 DANGER MAKE CERTAIN DRIVELINE YOKES ARE SECURELY FASTENED. FAILURE TO DO SO MAY RESULT IN SERIOUS H. Using cut off section of shield as a guide, cut INJURY. shaft the same amount. (Figure 2-4) Figure 2-4 L. Raise cutter off ground and adjust lower lift arms to level cutter right to left. Refer to tractor oper- ator’s manual. M. Lower cutter to work position. Adjust tractor top link to position
Resumen del contenido incluido en la página 12
SECTION III OPERATING INSTRUCTIONS 3-1 GENERAL SAFETY Figure 3-1 Only qualified people familiar with this operator’s manual and tractor operator’s manual should oper- ate this machine. Operator should wear hard hat, Spacers safety glasses and safety shoes. The operator should read, understand and practice all safety mes- Caster sages shown on the caution, warning and danger Wheel decals affixed to the cutter to avoid serious injury or death. It is recommended that tractor be equipped with Rollov
Resumen del contenido incluido en la página 13
SECTION IV MAINTENANCE 8.During operation, listen for abnormal sounds 4-1 MAINTENANCE CHECK LIST which might indicate loose parts, damaged bearings, Perform scheduled maintenance as outlined below. or other damage. Correct any deficiency before con- Lower implement to ground, turn off tractor, and set tinuing operation. parking brake before doing maintenance inspections or work. Some checks may require raising machine AFTER EACH USE off ground and supporting with blocks. All bolts 1. Clean all d
Resumen del contenido incluido en la página 14
7. Spindle Assembly - Apply 3 shots of multi- 4-4 BELT REPLACEMENT purpose grease with grease gun every 40 hours. Grease fittings for spindles are accessible Use only genuine Bush Hog replacement parts. through holes in the shields. A. Remove right and left side shields. B. Relieve spring tension by loosening the two 4-3 BELT ADJUSTMENT 1/2” hex nuts on the spring adjustment rod. (Figure 4-1 C) C. Remove old belt. D. Install new belt as shown below. (Also refer to Belt tensions should be check
Resumen del contenido incluido en la página 15
Figure 4-2 Blade Placement 4-5 BLADE REPLACEMENT CAUTION Spindle Assembly WEAR HEAVY WORK GLOVES TO PRO- TECT HANDS FROM SHARP EDGES. A. Raise cutter using tractor 3-point lift and SECURELY BLOCK INTO POSITION. B. Turn off tractor, set parking brake and remove key. C. Remove bolt and cup washer securing blade to spindle. Remove blade. Blade D. Install new blade as shown in Figure 4-2 with con- cave side of cup washer against blade. Be sure that blades are installed with offset in proper direct
Resumen del contenido incluido en la página 16
SECTION V DEALER ASSEMBLY AFTER COMPLETING ANY ASSEMBLY STEP, CAUTION THOROUGHLY READ THE NEXT STEP IN THE THE FOLLOWING SAFETY PRECAUTIONS ASSEMBLY INSTRUCTIONS BEFORE PRO- SHOULD BE THOROUGHLY UNDERSTOOD CEEDING WITH THAT STEP. BEFORE ATTEMPTING MACHINE ASSEMBLY. 11. After completing assembly, thoroughly inspect 1. Wear personal protective equipment such as, the machine to be sure that all nuts, bolts, hydraulic but not limited to, protection for eyes, ears, feet, fittings or any other fastene
Resumen del contenido incluido en la página 17
E. Fasten mast supports and upper flex link to the right and left roller mounts to the deck in the mast halves using 1/2 x 5” capscrew, pivot tube and holes provided by using 3/8 x 1” carriage bolts, flat- locknut.. washers, lockwashers and hex nuts. Install bolts F. Place two long spacers on the caster stems with heads to inside of deck. (Figure 5-2) Assemble and insert into caster arms. Place two long spacers roller, roller sleeve, capscrew and locknut as shown and two short spacers on the cas
Resumen del contenido incluido en la página 18
SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more information. IMPLEMENT CAN FALL FROM HYDRAULIC SYSTEM RELEASE. TO AVOID SERIOUS INJURY OR DEATH: SHUT OFF TRACTOR ENGINE, REMOVE KEY, SECURE • TRACTOR PA
Resumen del contenido incluido en la página 19
TORQUE SPECIFICATIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* AMERICAN BOLT DIAMETER Bolt Head Markings WRENCH (IN.) “B” AND SAE SAE SAE SIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18) 1/2 5/16 - 18 UNC 11 (15) 17 (23) 25 (33) SAE Grade 2 1/2 5/16 - 24 UNF 13 (17) 19 (26) 27 (37) (No Dashes) 9/16 3/8 - 16 UNC 20 (27) 31 (42) 44 (60) 9/16 3/
Resumen del contenido incluido en la página 20
l l 2501 Griffin Ave. Selma, AL 36703 l l Telephone (334) 874-2700 www.bushhog.com
