Resumen del contenido incluido en la página 1
ATTACHMENT
OPERATOR’S
MANUAL
2-BIN BAGGER
50” 2-Bin Bagger
Mfg. No. Description
1695284 50” 2-Bin Bagger
1734240
Rev. 00
Rev. Date 01/2007
TP 100-4452-00-AT-SN
Resumen del contenido incluido en la página 2
THIS PAGE INTENTIONALLY BLANK
Resumen del contenido incluido en la página 3
Table of Contents Safety Rules & Information General Warnings............................................2 Safety Decals ..................................................2 General Operating Instructions Before Operation .............................................3 Mowing with the Catcher .................................3 After Operation ................................................3 Storing the Grass Catcher...............................3 Initial Installation Counterweight Installation .
Resumen del contenido incluido en la página 4
Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. GENERAL WARNINGS � Know the unit’s controls and how to stop quickly. bag that meets manufacturer’s durability standards. READ THE OPERATOR’S MANUALS. � If the mower stall
Resumen del contenido incluido en la página 5
General Operating Instructions Before Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag is very important. For this reason, BEFORE YOU BEGIN MOWING you should make certain the underside of the mower and the u
Resumen del contenido incluido en la página 6
Initial Installation NOTE: In this manual, “left” and “right” are always defined from the standpoint of the operator position facing forward from seat. WARNING To avoid serious injury, engage parking brake, disengage PTO, stop engine, remove key and disconnect spark plug(s) before attempting to B install, remove or work on the mower. D COUNTERWEIGHT INSTALLATION 1. Slide pins (A, Figure 1) on counterweight (B) into C B slots (C) on front footrest support bracket (D). C 2. Secure counterweight (B
Resumen del contenido incluido en la página 7
Hitch Installation B B A A D F C E H G J I Left View Back View Figure 4. Install Hitch Assembly A. Frame F. Nut, Nylock, Flanged 3/8-16 B. Hitch Assembly G. Nut, Nylock, Flanged 5/16-16 C. Debris Guard H. Nut, 1/2-13 D. Capscrew, Debris Guard, 3/8-16 I. Nut, 3/8-16 E. Capscrew, Seat Deck Support, 5/16-18 J. Rear Transmission Support HITCH INSTALLATION Hitch Installation 1. Remove 5/16-16 nut (G, Figure 4) from seat deck support capscrew (E). 2. Remove 3/8-16 nut (F) from rear debris guard capsc
Resumen del contenido incluido en la página 8
Bag Support and Cover Installation B E C F D G E A C A D Figure 5. Install Bag and Cover Support B A. Upright Support B. Bag and Cover Support E C D C. Support Mount D. Mount Pin Figure 6. Cover Installation E. Retainer Spring A. Cover Assembly F. Shoulder Rest B. Bag Support Bracket G. Shoulder Bolt C. Cover Hinge Pivots D. Hinge Pins Bag Support Installation E. Retainer Springs 1. Attach the bag and cover support (B, Figure 5) to the upright support (A) by sliding the support mount (C) INSTA
Resumen del contenido incluido en la página 9
Bag Installation and Tube Assembly A 50” Mowers A B C 50” Mowers C B D Figure 8. Middle and Upper Tube Assembly A. Upper Tube Figure 7. Install Collector Bags B. Middle Tube A. Cover C. Screw, 1/4 x 3/4 B. Collector Bags CONNECTING UPPER AND MIDDLE TUBE C. Grass Bag Hanger D. Bag Hanger Post 1. Slide the upper tube (A, Figure 8) over middle tube (B) and secure together using screw (C). INSTALL COLLECTOR BAGS In upper tube: 1. Raise the cover (A, Figure 7). - Fourth hole from end is for 50” mo
Resumen del contenido incluido en la página 10
Chute and Tube Installation D H F C E H B G A D F C G A B E Figure 9. Install Chute A. Mounting Plate Figure 10. Connecting Tube Assembly to Lower B. Locknuts, 5/16-18 Chute and Cover C. Carriage Bolt, 5/16-18 x 5/8 A. Upper Tube D. Chute Rod B. Cover E. Rubber Strap C. Ridge, Upper Tube F. Discharge Deflector D. Ridge Cutout G. Locknut E. Lower Chute H. Mounting Hole F. Strap, Rubber G. Pin H. Tube Assembly Chute Installation CONNECTING TUBE ASSEMBLY TO CHUTE AND COVER 1. Install mounting pla
Resumen del contenido incluido en la página 11
THIS PAGE INTENTIONALLY BLANK 9
Resumen del contenido incluido en la página 12
Normal Installation & Removal J A. Hitch Assembly B. Bag and Cover Support Assembly I K C. Shoulder Rest D. Mount Pin E. Retainer Spring L F. Hinge Pins G. Retainer Springs H. Cover hinge Pivots M I. Cover J. Bag N K. Bag Hanger L. Ridge Cutout H M. Upper Tube N. Ridge O. Middle Tube G B P. Rubber Strap, Middle F Q. Pin P E G R. Lower Chute F O S. Lower Chute Rod X T. Mounting Plate Q C D U. Rubber Strap, Lower Chute V. Discharge Deflector C W. Locknut Mount R V X. Support Mount U A W S T Figure
Resumen del contenido incluido en la página 13
Normal Removal WARNING OPERATION WITHOUT BAGGER For operation without bagger, the mower discharge deflector MUST be properly installed in the down position and retained by the spring latch. Removal 1. Unhook rubber strap (P, Figure 11) from pin (Q), then remove tube assembly (O) from chute (R) and from cover (I). 2. Lift cover (I) and remove bags (J) from bag and cover support assembly (B). Note: Support the cover during the next step. 3. Remove cover (I) by disconnecting retainer springs (G),
Resumen del contenido incluido en la página 14
MANUFACTURING, INC. Simplicity Mfg. Inc. - Snapper Products Simplicity Mfg. Inc. 500 N Spring 535 Macon Street Street / PO Box 997 McDonough, GA 30253 Port Washington, WI 53074-0997 www.Snapper.com www.SimplicityMfg.com Briggs & Stratton Yard Power Products Group Copyright © 2007 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved
