Manual de instrucciones de Toro Timemaster 20199

Manual de instrucciones del aparato Toro Timemaster 20199

Aparato: Toro Timemaster 20199
Categoría: Cortacésped
Fabricante: Toro
Tamaño: 2.42 MB
Fecha de añadido: 10/5/2013
Número de páginas: 28
Imprimir el manual

Descargar

¿Cómo se utiliza?

Nuestro propósito es proporcionarte el acceso más rápido posible a los contenidos incluidos en los manuales de instrucciones del aparato Toro Timemaster 20199. Utilizando la vista previa online, puedes ver rápidamente el índice de contenidos y pasar a la página donde encontrarás la solución a tu problema con Toro Timemaster 20199.

Para tu comodidad

Si ver los manuales de instrucción de Toro Timemaster 20199 directamente en esta página no es cómodo para ti, puedes utilizar dos soluciones posibles:

  • Vista en pantalla completa – Para ver cómodamente los manuales de instrucciones (sin descargarlos en tu ordenador) puedes utilizar el modo de vista en pantalla completa. Para activar la vista del manual Toro Timemaster 20199 en pantalla completa, utiliza el botón Pantalla completa
  • Descargar al ordenador – también puedes descargar el manual de instrucciones de Toro Timemaster 20199 a tu ordenador y guardarlo en tu colección. Sin embargo, si no quieres ocupar espacio en tu dispositivo, siempre podrás descargarlo de ManualsBase.
Toro Timemaster 20199 Manual de instrucciones - Online PDF
Advertisement
« Page 1 of 28 »
Advertisement
Versión impresa

Muchas personas prefieren no leer el documento en la pantalla, sino en versión impresa. La opción de impresión también está prevista y puedes utilizarla haciendo clic en el enlace más arriba - Imprimir el manual. No tienes que imprimir el manual completo de Toro Timemaster 20199, solo las páginas que elijas. Ahorra papel.

Resúmenes

A continuación encontrarás resúmenes de los contenidos incluidos en las páginas posteriores del manual de instrucciones para Toro Timemaster 20199. Puedes utilizarlos si quieres ver rápidamente el contenido que se encuentra en la siguientes páginas del manual.

Resúmenes de contenidos
Resumen del contenido incluido en la página 1

Form No. 3369-191 Rev A
T imeMaster™ 30in Lawn Mower
Model No. 20199 —Serial No. 31200001 and Up
Model No. 20200 —Serial No. 31200001 and Up
Operator's Manual
Introduction T his man ual identifies potential hazards and has safety
messag es identified b y the safety aler t symbol ( Figure 2 ),
T his r otar y-blade, w alk-behind la wn mo w er is
whic h signals a hazard that ma y cause serious injur y
intended to be used by r esidential homeo wner s.
or death if y ou do not follo w the recommended

Resumen del contenido incluido en la página 2

engine man ufacturer in accordance with SAE J1940. Do not tamper with the engine controls or alter the As configured to meet safety , emission, and operating g o v er nor speed; doing so ma y create an unsafe condition requirements , the actual engine horse po w er on this class resulting in personal injur y . of la wn mo w er will be significantly lo w er . Safety T his mac hine meets or ex ceeds the CPSC blade safety • Do not operate the mac hine without the entire g rass requirements for w al

Resumen del contenido incluido en la página 3

• Do not mo w on w et g rass or ex cessi v ely stee p slopes . • K ee p the nozzle in contact with the rim of the fuel P oor footing could cause a slip-and-fall accident. tank or container opening at all times until fueling is complete . Do not use a nozzle loc k-open device . • Do not mo w near drop-offs , ditc hes , or embankments . Y ou could lose y our footing or • If fuel is spilled on clothing, c hang e clothing balance . immediately . • Nev er o v erfill the fuel tank. R e place the fuel

Resumen del contenido incluido en la página 4

Safety and Instructional Decals Important: Safety and instr uction decals ar e located near ar eas of potential danger . R eplace dama ged decals. Manufacturer's Mark 1. Indicates that the blade is identified as a part from the original machine manufacturer . 1 14-7982 1. W arning—read the Operator's Manual . 2. Thrown object hazard—keep bystanders a safe distance from the machine. 3. Cutting/dismemberment hazard of hand or foot, mower blade—disconnect the spark-plug wire and read the instructio

Resumen del contenido incluido en la página 5

104-7953 Electric-start model only 1. W arning—read the Operator's Manual for information on charging the battery; contains lead; do not discard. 2. Read the Operator's Manual. 2 Setup 1 Important: R emo v e and discard the pr otecti v e plastic sheet that co v er s the engine. 1 G016547 Figure 3 Assembling the Handle 1. Upper handle 2. Knob (2) No Parts Required Procedure 1 W ARNING Assembling and unf olding the handle impr oper l y can dama ge the ca bles, causing an unsafe operating condition

Resumen del contenido incluido en la página 6

Note: Max. fill: 20 oz. (0.59 l), type: SAE 30 deterg ent oil with an API ser vice classification of SF , SG , SH, SJ , SL, or higher . 2 Installing the Blade-control Bar No Parts Required Procedure Install the blade-control bar into the upper handle ( Figure 5 ). G017514 Figure 6 3. Wipe off the dipstic k end with a clean cloth. 4. Inser t the dipstic k into the oil-fill tube , and screw it in until it stops . 5. R emo v e the dipstic k and read the oil lev el on the dipstic k; refer to Figure

Resumen del contenido incluido en la página 7

3 4 2 Charging the Battery 1 No Parts Required Procedure 4 Electric-star t model onl y R efer to Charging the Batter y ( pag e 18 ) . g017218 Figure 9 Product Overview Upper handle 8 1. T raction-assist handle 3. Blade-control bar 2. Blade-control bar lock 4. Ignition switch 1 7 9 6 2 5 4 3 10 2 11 1 12 13 14 g016439 15 16 g017219 4 3 Figure 8 Figure 10 1. Side-discharge deflector 9. Ignition switch 1. Grass bag 3. Side-discharge chute 2. Spark plug 10. Battery (not shown; 2. Rear-discharge plug

Resumen del contenido incluido en la página 8

Using Fuel Operation Stabilizer/Conditioner Before Starting Use a fuel stabilizer/conditioner in the mac hine to pro vide the follo wing benefits: Recommended Fuel • It k ee ps g asoline fresh during storag e up to 90 da ys . W hen storing the mac hine for more than 90 da ys , DANGER drain the fuel tank. Gasoline is extr emel y flamma ble and explosi v e. A • It cleans the engine while it is r unning . fir e or explosion fr om gasoline can bur n y ou and • It eliminates gum-lik e v ar nish build

Resumen del contenido incluido en la página 9

Important: If the oil lev el in the crankcase is Checking the Engine Oil Level too lo w or too high and y ou r un the engine, Ser vice Inter v al : Before eac h use or daily y ou may dama ge the engine. Max. fill: 20 oz. (0.59 l), type: SAE 30 deterg ent oil 6. Install the dipstic k securely b y hand. with an API ser vice classification of SF , SG , SH, SJ , SL, or higher . Adjusting the Cutting Height 1. Mo v e the mac hine to a lev el surface . 2. R emo v e the dipstic k ( Figure 12 ). W ARNIN

Resumen del contenido incluido en la página 10

Adjusting the Handle Height 4 3 5 2 Y ou can raise or lo w er the handle to a position more 6 1 comfor table for y ou. 7 1. Pull the handle-loc k lev er rearw ard to diseng ag e the handle-loc k pins ( Figure 16 ). 1 2 3 G017635 Figure 15 G016488 Rear cutting-height lever Figure 16 1. Handle-lock lever 3. Notches 1. 1 inch (2.5 cm) 5. 3 inches (7.6 cm)) 2. Handle-lock pin (2) 2. 1-1/2 inches (3.8 cm) 6. 3-1/2 inches (8.9 cm)) 3. 2 inches (5.1 cm) 7. 4 inches (10.2 cm) 4. 2-1/2 inches (6.4 cm) 2.

Resumen del contenido incluido en la página 11

Note: Do not hold the ignition k ey in the Star t Stopping the Engine position for long er than 5 seconds to prev ent bur ning out the star ter motor . Standard Model Press the tog gle switc h ( Figure 19 ) to the Stop position, and w ait for the engine to stop . G017516 G017636 Figure 19 Figure 17 • R ecoil-star t Handle: Electric-start Model 1. T ur n the ignition k ey to the R un position 1. T ur n the k ey to the Off position (Figure 20 ). ( Figure 17 ). 2. Pull the recoil handle slo wly to

Resumen del contenido incluido en la página 12

Using the Grass Bag Ser vice Inter v al : Before eac h use or daily Y ou can use the g rass bag to c hec k the blade-stop system. 1 1. R emo v e the rear -disc harg e plug . 2. Install the empty g rass bag on the mac hine . 2 g016484 3. Star t the engine . Figure 21 4. Eng ag e the blades . 1. Blade-control bar lock 2. Blade-control bar Note: T he bag should begin to inflate , indicating that the blades are rotating . 2. Hold the blade-control bar ag ainst the handle 5. W hile w atc hing the bag

Resumen del contenido incluido en la página 13

unsafe operating condition. Contact an A uthorized W ARNING Ser vice Dealer . A w or n g rass ba g could allo w small stones and other similar de bris to be thr o wn to w ard the operator or Recycling the Clippings bystander s and r esult in serious per sonal injur y or death. T his mac hine comes from the factor y ready to recycle Check the g rass ba g fr equentl y . If it is dama ged, g rass and leaf clippings bac k into the la wn. T o pre pare install a new T or o r eplacement ba g . the mac

Resumen del contenido incluido en la página 14

1 2 1 2 G016513 Figure 26 1. Bag rod 2. Notch (2) 4. Lo w er the rear deflector until it rests on the g rass bag . G017521 Figure 27 Removing the Grass Bag 1. Side-discharge deflector 2. Side-discharge chute T o remo v e the bag, rev erse the ste ps in Installing the Grass Bag abo v e . 2. Install the side-disc harg e c hute as sho wn in Figure 27 and Figure 28 , and close the deflector onto Side-discharging the Clippings the c hute . Use the side disc harg e for cutting v er y tall g rass . If

Resumen del contenido incluido en la página 15

Cutting Leaves Operating T ips • After cutting a leaf-co v ered la wn, ensure that at least General Mowing T ips half of the la wn sho ws through the cut lea v es . Y ou ma y need to mo w the lea v es ag ain. • Clear the area of loose stic ks , branc hes , stones , wire , twine , and other debris that the blades could hit. • If there are more than 5 inc hes (13 cm) of lea v es on the la wn, set the front cutting height 1 or 2 notc hes • A v oid striking solid objects with the blades . Nev er hig

Resumen del contenido incluido en la página 16

Maintenance Note: Deter mine the left and right sides of the mac hine from the nor mal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval After the first 5 hours • Change the engine oil. • Check the engine oil level. • Check the blade-stop system operation. • Check the air cleaner and clean or replace it, if necessary . Before each use or daily • Check the cutting blades. • W ash underneath the machine. • Charge the battery (electric-start

Resumen del contenido incluido en la página 17

Servicing the Air Filter Changing the Engine Oil Ser vice Inter v al : Y early Ser vice Inter v al : After the first 5 hours Before eac h use or daily Ev er y 50 hours 1. Loosen the fastener and remo v e the air filter co v er Y early ( Figure 30 ). Max. fill: 20 oz. (0.59 l), type: SAE 30 deterg ent oil with an API ser vice classification of SF , SG , SH, SJ , SL, 1 or higher . 1. Ensure that the fuel tank contains little or no fuel so that fuel does not leak out when y ou tip the mo w er 2 ont

Resumen del contenido incluido en la página 18

Charging the Battery Ser vice Inter v al : Ev er y 25 hours Before storag e Electric-star t model onl y W ARNING Batter y posts, ter minals, and r elated accessories contain lead and lead compounds, chemicals kno wn to the State of Calif or nia to cause cancer and r epr oducti v e har m. W ash hands after handling G017514 batter y . Figure 32 Charg e the batter y for 24 hours initially , then monthly (ev er y 25 star ts) or as needed. Alw a ys use the c harg er in a sheltered area, and c harg e

Resumen del contenido incluido en la página 19

1 Replacing the Fuse Electric-star t model onl y If the batter y does not c harg e or the engine does not tur n with the electric star ter , the fuse ma y be blo wn; re place it with a 40-amp plug-in type fuse . Important: Y ou cannot star t the machine with the electric star ter or charge the batter y unless a G017523 w or king fuse is installed. 1. Open the sealed fuse holder and re place the fuse ( Figure 35 ). Figure 36 1 1. Rear-deflector and handle-lock lever assembly 8. R emo v e the co v

Resumen del contenido incluido en la página 20

Adjusting the Self-propel Drive Servicing the Blade-drive Cable System W henev er y ou install a new self-propel cable , or if Ser vice Inter v al : Ev er y 50 hours the self-propel dri v e is out of adjustment, adjust the 1. R emo v e the blade-dri v e system co v er ( Figure 39 ). self-propel-dri v e cable . 1 1. Loosen the cable suppor t n ut ( Figure 37 ). G016491 2 Figure 37 Figure 39 1. Bolts 2. Cover 2. Pull do wn the cable jac k et (to w ard the mo w er) until there is no slac k in the c


Manuales de instrucciones similares
# Manual de instrucciones Categoría Descargar
1 Toro 13AX60RH744 Manual de instrucciones Cortacésped 130
2 Toro 20016 Manual de instrucciones Cortacésped 67
3 Toro 14AQ81RP744 Manual de instrucciones Cortacésped 20
4 Toro 14AK81RK744 Manual de instrucciones Cortacésped 5
5 Toro 14AQ81RP544, 14AK81RK544 Manual de instrucciones Cortacésped 5
6 Toro 14AP80RP744 Manual de instrucciones Cortacésped 8
7 Toro 22621223-24 Manual de instrucciones Cortacésped 24
8 Toro 71430, 71432 Manual de instrucciones Cortacésped 24
9 Toro 20066 Manual de instrucciones Cortacésped 14
10 Toro 14AP80RP544 Manual de instrucciones Cortacésped 6
11 Toro 4500-D Manual de instrucciones Cortacésped 75
12 Toro 20067 Manual de instrucciones Cortacésped 12
13 Toro Groundsmaster 3280-D Manual de instrucciones Cortacésped 33
14 Toro GREENSMASTER 3100 Manual de instrucciones Cortacésped 54
15 Toro LX420, LX460 Manual de instrucciones Cortacésped 76
16 2Wire 7-1/4 Inch Circular Saw 94245 Manual de instrucciones Cortacésped 3
17 Agilent Technologies E4371A Manual de instrucciones Cortacésped 0
18 Agilent Technologies E4370A Manual de instrucciones Cortacésped 3
19 Agilent Technologies E4374A Manual de instrucciones Cortacésped 1
20 Adams 22 Manual de instrucciones Cortacésped 1