Resumen del contenido incluido en la página 1
GRASS COLLECTION
SYSTEM
PEC PEC PEC PEC PECO O O O O
PPPPP
DESIGNED FOR:
MODEL 22621223 - 24
toro z100 series
OPERATOR’S MANUAL
ASSEMBLY OPERATION MAINTENANCE
MANUAL PART#: Q0309 $4.00 REV: 0
Resumen del contenido incluido en la página 2
PECO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety 2 2-10 Adjustment Of The Hose Length 9 Safety Alert Symbols 3 2-11 Attachment Of The Upper Hose 9 Warranty 4 2-12 Attachment Of The Lower Hose To The I INTRODUCTION AND DESCRIPTION 5 Engine/Blower/Blade Assembly 9 1-1 Introduction 5 2-13 Attachment Of The Boot To The ZT Mower Deck 10 1-2 Description 5 2-14 Attachment Of The Lower Hose To The Boot 10 II PREPARATION FOR USE 5 2-15 Front Weight Assembly 10 2-1 Modificat
Resumen del contenido incluido en la página 3
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. WARNING! To avoid serious injury, perform maintenance on the vacuum collector; ONLY AFTER STOPPING THE MOWER’S ENGINE AND WAITING FOR ALL MOVING PARTS TO COME TO A COMPLETE STOP
Resumen del contenido incluido en la página 4
PECO LIMITED WARRANTY FOR NEW PRODUCTS A. WHAT IS WARRANTED? Peco extends the following warranties to the original purchaser of each new Peco consumer product subject to The following limitations. 1. PRODUCT WARRANTY: Any part of any consumer product, which is defective in material or workmanship as delivered to the purchaser will be repaired or replaced, as Peco elects, without charge for parts or labor, if the defect appears within 12 months from the date of delivery of the product to the orig
Resumen del contenido incluido en la página 5
SECTION I INTRODUCTION AND DESCRIPTION 1-1 Introduction Figure 1 Rear Heat Guard Removal We are pleased to have you as a PeCo customer. Your collection system has been designed to give you a low maintenance, simple, and effective way to collect the grass clippings from your ZT mower. This manual is provided to give you the necessary instructions to properly mount and operate the collection system on your ZT mower. Please read this manual thoroughly. Understand what each control is for and how to
Resumen del contenido incluido en la página 6
The inlet, (Figure 7), will need to be attached to the 2-3 Attaching The Lift Handle To The container. Open the container, push the inlet, from the Aluminum Grass Container inside of the container through the hole in the container to the outside. Orient the inlet opening to face the ground. Use the tabs P#(B1668) inside of the box to hold The various parts of the handle assembly P#(A0273) the inlet in place. It is recommended that two people must be attached to the container frame. (Figure 4) Pe
Resumen del contenido incluido en la página 7
Figure 4 Figure 7 Aluminum Grass Container Assy. Lift Handle Assy. Handle Grip Handle Mount Bracket Latch Rod Figure 5 Aluminum Grass Container With Handle Attached Figure 6 Latch Hook Mechanism Assembled 7
Resumen del contenido incluido en la página 8
Figure 8 Aluminum Grass Container Exploded View Figure 9 Misc. Parts Exploded View (1) (1) (1) B1810 A0507 HB0175 BOOT PLATE WEIGHT (1) HARDWARE ASSEMBLY A0060 BAG SHORT THROTTLE CABLE KIT (2) (2) J6006 J6011 7”-8” 5”-6” HOSE CLAMP HOSE CLAMP (1) E1039 (1) BOOT 6” x 32” UPPER HOSE (1) (1) E6009 A0403 8” MAIN FRAME (1) BLOWER ASSEMBLY ENGINE/ CONE BLOWER/ BLADE ASSEMBLY (1) (1) B1117 (1) 8” x 40” OUTER A0318 LOWER ENGINE ENGINE MOUNT HOSE MOUNT TUBE TUBE 8
Resumen del contenido incluido en la página 9
2-10 Adjustment Of The Hose Length 2-8 Engine Mount Arm Installation THE HOSES IN STEPS 2-11 AND 2-12 MUST BE CUT Slide the engine mount arm assembly (Figure 10) into TO FIT YOUR MACHINE. FOLLOW STEPS 2-11 AND the outer engine mount tube. Secure the engine mount 2-12. DO NOT CUT THE HOSES UNTIL YOU HAVE arm assembly using (1) detent pin P#(J0248). TRIED TO FIT THEM ON YOUR MACHINE. REMEMBER THAT THE HOSES HAVE TO BE LONG Figure 10 Engine Mount Arm ENOUGH TO ALLOW FOR ENOUGH CLAMPING SURFACE BETW
Resumen del contenido incluido en la página 10
2-13 Attachment Of The Boot To The ZT Mower Deck Figure 14 Front Weight Assembly To mount the boot plate P#(B1810) to the boot P#(E1039), use (2) 3/8” x 1” carriage bolts P#(K1182) and (2) 3/8” flange nuts P#(K1215). Be sure that, when fastening the boot and boot plate together, the head of the bolt is placed from the inside of the boot. This will prevent grass from collecting on the bolts. Hang the boot onto the mower deck (Figure 13). The slots in the boot plate will allow for adjustment left
Resumen del contenido incluido en la página 11
SECTION III SECTION IV OPERATING INSTRUCTIONS MAINTENANCE 3-1 General Safety 4-1 Maintenance Checklist Only qualified people familiar with this operator’s manual Before each use: and the ZT operator’s manual should operate this 1. Check blades and spindles to be sure that no foreign machine. objects, such as wire or steel strapping bands, are wrapped around them. 3-2 Operation 2. Inspect blades for wear. Replace if necessary. If it is necessary to sharpen the blades, remove the blades from the s
Resumen del contenido incluido en la página 12
SECTION V PARTS AND SERVICE 5-1 Parts And Service Information PeCo collection system owners should record the name and telephone number of their Service Center. Your Service Center will be happy to supply replacement parts, accessories, and do any service or repairs to your collection system. If for any reason your Service Center is unable to service your collection system or supply replacement parts, contact PeCo and include the following information on the chart below. THE SERIAL NUMBER PLATE
Resumen del contenido incluido en la página 13
13
Resumen del contenido incluido en la página 14
NOTES 14
Resumen del contenido incluido en la página 15
NOTES 15
Resumen del contenido incluido en la página 16
PEC PEC PEC PEC PECO O O O O PPPPP P.O. BOX 1197 ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: pecoinc1@bellsouth.net WEBSITE: WWW.LAWNVAC.COM
