Resumen del contenido incluido en la página 1
STIGA TURBO
55 COMBI
48 COMBI
43 COMBI
8211-0208-11
Resumen del contenido incluido en la página 2
S SVENSKA B 1. 2. B 3. 4. D F E 5. 6. 7.
Resumen del contenido incluido en la página 3
S SVENSKA FULL ADD 8. 9. Briggs & Stratton LS 45 0,15 l. FULL/MAX ADD/MIN 10. Briggs & Stratton XTE 11. Honda GCV 3x 12. Briggs & Stratton LS 45 13. Briggs & Stratton XTE G I* B* 14. Honda GCV 15. ADD FULL ADD FULL
Resumen del contenido incluido en la página 4
S SVENSKA X Y 16. 17. 18. 19. Left 20. Right 21. Briggs & Stratton LS 45 22. Briggs & Stratton XTE 23. Honda GCV 24.
Resumen del contenido incluido en la página 5
S SVENSKA 25. 26. S S T 27. 28. 40 Nm 40 Nm 29. Regular blade holder 30. Friction blade holder S 31 A. 48 cm / 55 cm 31 B. 43 cm
Resumen del contenido incluido en la página 6
GB ENGLISH SYMBOLS 3 The following symbols can be found on the ma- chine to remind you of the care and attention that are required during use. 5 The symbols mean: 2 Warning! Read the Instruction Book and Safety Manual before using the machine. 4 1 Warning! Keep onlookers away. Beware Type II of objects being flung out. 3 Warning! Keep hands and feet clear of the 2 cutting deck when the machine is running. 1 Warning! Before starting any repair work, remove the spark plug cable from the spark plug
Resumen del contenido incluido en la página 7
GB ENGLISH VARIATOR CONTROL (*) INSTALLATION When the mower is delivered, the variator cable is set so that the transmission cannot be damaged. LOOSE PARTS IN THE BOX The cable may need tightening, see under heading “ADJUSTING VARIATOR CABLE“ in the sec- 2 brackets for the grass collector tion “MAINTENANCE“. 4 screws for the brackets 1 ignition key (*) GRASS COLLECTOR 1 battery charger (*) 1 Allen key Raise the collector flap and attach the two brackets 1 socket wrench to the grass collector wit
Resumen del contenido incluido en la página 8
GB ENGLISH To remove the plug, press in the catch (S). On re- NOTE! If you change to environmental- installing the plug ensure that both pins are pressed ly friendly petrol in an engine previously firmly into the holes so that the plug snaps in place. run on ordinary lead-free petrol (95), the petrol manufacturer’s recommenda- Turbo43Combi: tions must be followed carefully. To remove the plug, unscrew the wing nut. Ordinary lead-free 95 octane petrol can also be 2. COLLECTION used. You must neve
Resumen del contenido incluido en la página 9
GB ENGLISH STARTING THE ENGINE (Honda) REAR WHEEL DRIVE (*) 1. Place the lawnmower on flat, firm ground. Do Engage the drive by pressing the clutch loop I to- not start in long grass. wards the handle. Disengage the drive by releasing the clutch loop I (fig. 15). 2. Make sure the spark plug cable is connected to the spark plug. SPEED (*) 3. Open the fuel tap (fig. 14). Do not touch the variator control when the engine is not running. This can dam- 4. Set the throttle control B in the choke posi-
Resumen del contenido incluido en la página 10
GB ENGLISH If grass has dried on to the mower casing, it can be AIR FILTER scraped clean. If necessary, touch up the underside A dirty and blocked air filter reduces the engine with paint to prevent rust damage. output and increases engine wear. Clean the silencer and the surrounding Briggs & Stratton LS 45 (fig. 21): Carefully re- area regularly to remove grass, dirt and move the air cleaner so that no dirt falls down into flammable waste products. the carburettor. Remove the expanded plastic f
Resumen del contenido incluido en la página 11
GB ENGLISH 2. When the clutch loop is BATTERY (*) pressedinapprox.2cm(posi- The electrolyte in the battery is toxic tion 1), there should be some and corrosive. It can cause serious cor- resistance when pushing the rosion damage etc. Avoid all contact lawnmower. With the clutch with skin, eyes and clothing. loop fully pressed in (position 2) it should not be possible to In normal use during the season, the battery is push the mower. Unscrew the charged by the engine. If the engine cannot be nipp
Resumen del contenido incluido en la página 12
GB ENGLISH When replacing the blade, the blade screw should also be replaced. The guarantee does not cover damage to the blade, blade holder or engine caused by running into ob- stacles. When replacing the blade, blade holder and blade screw, always use genuine spare parts. Non-genu- ine spare parts can entail a risk of injury or dam- age, even if they fit the machine. SHARPENING THE BLADES Sharpening of the blades must be done by wet method grinding, using a whetstone or a grind- stone. For saf
Resumen del contenido incluido en la página 13
MO WI NG A H E A D BOX 1006 · SE-573 28 TRANÅS www.stiga.com
