Manual de instrucciones de Snapper Simplicity RZT Riding Mowers

Resumen del contenido incluido en la página 1

#7600029 TRIPLE BAG CATCHER KIT FOR
44 & 50” SNAPPER / SIMPLICITY RZT RIDING MOWERS
WARNING
! !
DO NOT attempt any adjustments, maintenance, repairs, or service with engine running. Stop engine. Engage
parking brake. Remove key. Remove spark plug wire and secure wire away from spark plug. Engine, muffler and
surrounding areas are extremely hot. Avoid serious burns; allow components to cool down before installing kit.
Replace worn or damaged parts prior to operating. Use approved fuel container.

Resumen del contenido incluido en la página 2

STEP 4: Install the bag adapter deck mounting hardware: LOCK NUT ADAPTER a. Install the 1/4 x 2-1/2” hex bolt, fitted with one 1/4-20 STRAP flange nut threaded all the way up to the end of the thread, into the noted hole in the rear of the deck. See Figure 5. FLANGE Secure with a second flange nut, tightening securely. NUTS b. Attach the rod mount plate to the right front of the deck with two 5/16 x 3/4” hex bolts and center lock nuts, tightening securely. See Figure 5. 50” DECKS ONLY: Before

Resumen del contenido incluido en la página 3

b. Install the catcher support onto the unit, securing with the 2” BOLT (2) hardware noted in Figure 9. Tighten all hardware securely. SQUARE NOTE: Be sure to reinstall any components that may have END CAP (2) been removed when removing the hardware in Step 7a. SECURE WITH SUPPLIED 5/16 ROUND SECURE WITH x 3/4” HEX END SUPPLIED 5/16 WASHER HEAD CAP (8) x 3/4” HEX BOLT & WASHER FLANGE NUT HEAD BOLT LOCK NUT (4) 2-1/4” BOLT (2) BAGGER CHANNEL FIGURE 11 SECURE WITH REMOVED STEP 10: Install the cove

Resumen del contenido incluido en la página 4

STEP 12: Assemble the discharge tubes: a. Install one strap assembly to each of the locations marked ‘A’ in Figure 16. Insert one #10-24 x 5/8” pan head screw, fitted with one #10 x 1/2” OD flat washer, out through the hole in the tube or adapter. Secure with one #10 x 3/4” OD flat washer, strap, and #10-24 tee nut, tightening securely. See Figure 14. FIGURE 16 c. Install the large end of the lower tube (short, straight tube) ATTACH TO ALL onto the end of the adapter, and secure the strap o

Resumen del contenido incluido en la página 5

STEP 13: Assemble the grass containers: COVER HANDLE a. Match each container section with its corresponding SHOULD LOCK ONTO sections (see Figure 18): CONTAINERS WHEN COVER IS CLOSED Container 1 A1, A2, A3 Container 2 B1, B2, B3 CONTAINER 3 Container 3 A1, A2, A3 (or B1, B2, B3). b. With the matched numbers aligned, insert the bottom section (A3, B3) of each container through the middle section (A2, B2), and the middle section through the top section (A1, A1), until the tabs around the top of ea

Resumen del contenido incluido en la página 6

7600029 TRIPLE BAG CATCHER COMPONENTS SHEET 1 6

Resumen del contenido incluido en la página 7

7600029 TRIPLE BAG CATCHER COMPONENTS ITEM NO. PART NO. DESCRIPTION QTY 1 7100688 ASSY., Triple Cover - 44"/50" 1 2 720537 HANDLE, Cover 1 3 7036415 SCREW, Cross Recess Pan Head, 10-24 X 5/8 6 4 7091290 NUT, Hex Lock 10-24 2 5 726853 HINGE, Cover 1 6 7091530 BOLT, Carriage 1/4-20 X 3/4 4 7 7091294 WASHER, SAE 1/4 4 8 7092126 NUT, Hex Center Lock 1/4-20 4 9 720525 PIN, Cover Hinge 1 10 7091503 PIN, Hair 3/32 X 1.5 3 11 7400196 WELDMENT, Triple Catcher Frame 1 12 7076938 SCREW, Hex Head Cap 5/16-1

Resumen del contenido incluido en la página 8

7600029 TRIPLE BAG CATCHER COMPONENTS SHEET 2 NOTE: Item Numbers 18-21 Required for 50” Decks Only 8

Resumen del contenido incluido en la página 9

7600029 TRIPLE BAG CATCHER COMPONENTS ITEM NO. PART NO. DESCRIPTION QTY 1 7091256 SCREW, Hex Head Cap 1/4 - 20 X 2-1/4 1 2 7091584 NUT, Hex Flange 1/4-20 2 3 1726578 PLATE, Rod Mount 1 4 7090799 BOLT, Carriage 5/16-18 X 5/8 9 5 7091601 NUT, Flange 5/16-18 12 6 7090188 WASHER, SAE 5/16 4 7 1731428 ROD, Adapter Mount 1 8 7091318 SCREW, Hex Head Cap 5/16-18 X 3/4 1 9 7091602 BOLT, Hex Flange 5/16-18 X 1.5 1 10 2171600 STRAP, Rubber 1 11 7091298 NUT, Hex Lock 5/16-18 3 12 7100692 ADAPTER, Bag 1 13 1

Resumen del contenido incluido en la página 10

NOTES 10

Resumen del contenido incluido en la página 11

NOTES 11

Resumen del contenido incluido en la página 12

INSTRUCTION No. 7101095 (I.R. 9/19/2006) TP 200-5231-IR-AT-SN 12