Manual de instrucciones de Sub-Zero 430/F

Manual de instrucciones del aparato Sub-Zero 430/F

Aparato: Sub-Zero 430/F
Categoría: Dosificador de bebidas
Fabricante: Sub-Zero
Tamaño: 0.62 MB
Fecha de añadido: 4/9/2014
Número de páginas: 36
Imprimir el manual

Descargar

¿Cómo se utiliza?

Nuestro propósito es proporcionarte el acceso más rápido posible a los contenidos incluidos en los manuales de instrucciones del aparato Sub-Zero 430/F. Utilizando la vista previa online, puedes ver rápidamente el índice de contenidos y pasar a la página donde encontrarás la solución a tu problema con Sub-Zero 430/F.

Para tu comodidad

Si ver los manuales de instrucción de Sub-Zero 430/F directamente en esta página no es cómodo para ti, puedes utilizar dos soluciones posibles:

  • Vista en pantalla completa – Para ver cómodamente los manuales de instrucciones (sin descargarlos en tu ordenador) puedes utilizar el modo de vista en pantalla completa. Para activar la vista del manual Sub-Zero 430/F en pantalla completa, utiliza el botón Pantalla completa
  • Descargar al ordenador – también puedes descargar el manual de instrucciones de Sub-Zero 430/F a tu ordenador y guardarlo en tu colección. Sin embargo, si no quieres ocupar espacio en tu dispositivo, siempre podrás descargarlo de ManualsBase.
Sub-Zero 430/F Manual de instrucciones - Online PDF
Advertisement
« Page 1 of 36 »
Advertisement
Versión impresa

Muchas personas prefieren no leer el documento en la pantalla, sino en versión impresa. La opción de impresión también está prevista y puedes utilizarla haciendo clic en el enlace más arriba - Imprimir el manual. No tienes que imprimir el manual completo de Sub-Zero 430/F, solo las páginas que elijas. Ahorra papel.

Resúmenes

A continuación encontrarás resúmenes de los contenidos incluidos en las páginas posteriores del manual de instrucciones para Sub-Zero 430/F. Puedes utilizarlos si quieres ver rápidamente el contenido que se encuentra en la siguientes páginas del manual.

Resúmenes de contenidos
Resumen del contenido incluido en la página 1

W INE S TORAGE
INSTALLATION INSTRUCTIONS

Resumen del contenido incluido en la página 2

SUB-ZERO WINE STORAGE The importance of the installation of the Sub-Zero Wine Storage unit cannot be overemphasized. Installation should be done by a qualified installer. Before you begin the installation process, it CONTENTS is recommended that you read this entire Installation Instructions book. There are key Models 424 and 424FS Installation 3 details that you should take special care to observe during the installation. By reading Models 427 and 427R Installation 12 these instructions careful

Resumen del contenido incluido en la página 3

MODELS 424 AND 424FS INSTALLATION MODELS 424 AND 424FS MODELS 424 | 424FS SITE PREPARATION INSTALLATION SPECIFICATIONS The Sub-Zero Model 424FS wine storage unit TOP VIEW is designed to be attractive in a stand alone 24" setting. It can also be slid into surrounding (610) ROUGH cabinetry with clearance dimensions slightly OPENING different than the standard built-in Model 424. DEPTH Make sure that the finished rough opening where the Wine Storage unit is to be installed ROUGH OPENING is

Resumen del contenido incluido en la página 4

MODELS 424 AND 424FS INSTALLATION MODELS ELECTRICAL REQUIREMENTS UNPACKING AND MOVING 424 | 424FS A 115 V AC, 60 Hz, 15 amp circuit breaker and Uncrate the unit, remove its wood base and electrical supply are required. A separate discard the shipping bolts that hold the wood circuit, servicing only this appliance, is base to the bottom of the unit. Remove all required. packing materials and tape. The power supply cord has a 3-prong ground- IMPORTANT NOTE: Do not discard the ing plug, which must

Resumen del contenido incluido en la página 5

MODELS 424 AND 424FS INSTALLATION ANTI-TIP BRACKET INSTALLATION MODELS 424 | 424FS MODEL 424FS To prevent the unit from tipping forward If you are installing the Model 424FS in a 5 and provide a stable installation, the unit space deeper than 24 /8" (625), the anti-tip must be secured in place with the anti-tip 5 bracket must be installed no more than 24 /8" bracket. (625) deep, so it engages the unit properly. It is important that this measurement be made from the front surface of the door, to

Resumen del contenido incluido en la página 6

MODELS 424 AND 424FS INSTALLATION MODELS ANTI-TIP BRACKET INSTALLATION 424 | 424FS WOOD FLOOR APPLICATIONS Installation for Concrete Wedge Anchors: 3 1 1) Drill a /8" (10) diameter hole any depth Use the four #12 x 2 /2" wood screws and the 1 exceeding the minimum embedment. Clean four /4" flat washers provided. Drill pilot holes 3 the hole or continue drilling additional /16" (5) diameter maximum, and be sure that depth to accommodate drill fines. Use a the screws penetrate through the flooring

Resumen del contenido incluido en la página 7

MODELS 424 AND 424FS INSTALLATION LOCK INSTALLATION MODELS 424 | 424FS IMPORTANT NOTE: If you are adding an If a home alarm system is to be used with the accessory lock kit to your Wine Storage unit, it Wine Storage unit, the lead wires should be should be installed before you position the threaded into the compressor compartment unit. Installation instructions are included with before you position the unit. See Home Alarm the lock kit. Connections on page 8, for the location of these lead wires

Resumen del contenido incluido en la página 8

MODELS 424 AND 424FS INSTALLATION MODELS LEVEL THE UNIT HOME ALARM CONNECTIONS 424 | 424FS Using an adjustable wrench or pliers, turn Before the kickplate is installed, all necessary each of the four leveling legs clockwise to raise wiring connections in the compressor compart- the unit and counterclockwise to lower the ment should be completed. unit. For the location of the leveling legs, see If a home alarm system is to be installed on illustration 6 below. the Wine Storage unit, the connectio

Resumen del contenido incluido en la página 9

MODELS 424 AND 424FS INSTALLATION KICKPLATE INSTALLATION DOOR PANELS – MODEL 424 MODELS 424 | 424FS Once the unit is leveled and wiring connections Model 424 is offered in two design applica- made, the kickplate can be installed. Use the tions; stainless steel (/S) and overlay (/O). Each 1 two #10 x /2" stainless steel screws that are of these designs are available as a glass door provided with the kickplate. Refer to illustration (G) model. 8 below. The stainless steel Model 424 is available in

Resumen del contenido incluido en la página 10

MODELS 424 AND 424FS INSTALLATION MODELS OVERLAY DOOR PANELS 424 | 424FS OVERLAY GLASS DOOR – MODEL 424 IMPORTANT NOTE: After the first three or four mounting screws are in place, but not 5 Inspect the door panel for the minimum /8" completely tightened, close the door and check (16) thickness, the finished inside edge and the your panel fit. This is the time to make small 10 lbs (5 kg) weight limit. See the Wine adjustments. Once you are satisfied with the Storage section of the Sub-Zero Design

Resumen del contenido incluido en la página 11

MODELS 424 AND 424FS INSTALLATION HINGE ADJUSTMENT MODELS 424 | 424FS IMPORTANT NOTE: Install screws in all the IMPORTANT NOTE: The Wine Storage unit mounting holes in the door frame. The nature must be installed and leveled before door of the door panel with a narrow outer rim and hinge adjustments can be made. no connecting center member requires the The top and bottom cabinet hinges on Models support provided by the glass door. 424 and 424FS are held in place with three After the door panel i

Resumen del contenido incluido en la página 12

MODELS 427 AND 427R INSTALLATION MODELS MODELS 427 AND 427R 427 | 427R INSTALLATION SPECIFICATIONS SITE PREPARATION Make sure that the finished rough opening where the Wine Storage unit is to be installed 25" is properly prepared. Refer to the Installation (635) ROUGH Specifications illustration for rough opening OPENING dimensions, door swing clearance and electri- DEPTH cal placement for Models 427 and 427R. IMPORTANT NOTE: To operate properly, the TOP VIEW door must open a minimum of 90 degre

Resumen del contenido incluido en la página 13

MODELS 427 AND 427R INSTALLATION ELECTRICAL REQUIREMENTS UNPACKING AND MOVING MODELS 427 | 427R A 115 V AC, 60 Hz, 15 amp circuit breaker and Uncrate the unit, remove its wood base and electrical supply are required. A separate discard the shipping bolts that hold the wood circuit, servicing only this appliance, is base to the bottom of the unit. Remove all required. packing materials and tape. The power supply cord has a 3-prong ground- IMPORTANT NOTE: Do not discard the ing plug, which must b

Resumen del contenido incluido en la página 14

MODELS 427 AND 427R INSTALLATION MODELS ANTI-TIP BRACKET INSTALLATION 427 | 427R WOOD FLOOR APPLICATIONS 1 Use the six #12 x 2 /2" wood screws and the To prevent the unit from tipping forward 1 and provide a stable installation, install six /4" flat washers provided. Drill pilot holes 3 the anti-tip bracket and extend the front /16" (5) diameter maximum, and be sure that leveling legs to the floor. the screws penetrate through the flooring material and into the wall plate a minimum of 3 /4" (19)

Resumen del contenido incluido en la página 15

MODELS 427 AND 427R INSTALLATION POSITION THE UNIT MODELS 427 | 427R Installation for Concrete Wedge Anchors: 3 1) Drill a /8" (10) diameter hole any depth Before moving the Wine Storage unit into exceeding the minimum embedment. Clean position, secure the door closed. Remove the hole or continue drilling additional the drawers of the Model 427R. depth to accommodate drill fines. Use a OPTIONAL carbide drill bit manufactured within ANSI COMPONENTS B94.12-77. IMPORTANT NOTE: For Model 427R, the t

Resumen del contenido incluido en la página 16

MODELS 427 AND 427R INSTALLATION MODELS POSITION THE UNIT 427 | 427R IMPORTANT NOTE: If you are adding an If a home alarm system is to be used with the accessory lock kit to your Model 427 or 427R, Wine Storage unit, the lead wires should be the catch should be installed at the top of threaded into the compressor compartment appliance cabinet before you position the unit. before you position the unit. See Other Wiring See Lock Installation on page 23. Installation Connections on page 18 for the

Resumen del contenido incluido en la página 17

MODELS 427 AND 427R INSTALLATION LEVEL THE UNIT MOLDING INSTALLATION MODELS 427 | 427R Level the unit by turning the front leveling legs The decorative white molding strips for the clockwise to raise the unit, or counterclockwise side and top of Models 427 and 427R can be to lower it. To assist you in adjusting the front snapped into place. The top molding piece leveling legs up or down, use a standard must be installed before the side molding can screwdriver blade and place it in the front be a

Resumen del contenido incluido en la página 18

MODELS 427 AND 427R INSTALLATION MODELS OTHER WIRING CONNECTIONS 427 | 427R Before the kickplate/grille is installed, all IMPORTANT NOTE: If you are not responsible necessary wiring connections in the compres- for alarm system connection, this information sor compartment should be completed. should be supplied to the home security system contractor. If the dual installation heater kit (#7007529) is used with Model 427 or 427R, the power OPTIONAL supply leads should be connected according to COMP

Resumen del contenido incluido en la página 19

MODELS 427 AND 427R INSTALLATION KICKPLATE / GRILLE INSTALLATION MODELS 427 | 427R Once the unit is leveled and wiring connec- Stainless steel panels in three finishes in most tions made, the kickplate/grille can be cases; classic (/S), platinum (/P) and carbon installed. (/B)—available as sales accessories—may be configured several ways and are shipped IMPORTANT NOTE: The kickplate/grille must separately. Stainless steel panels are shipped be removed for servicing. The floor cannot PANEL with m

Resumen del contenido incluido en la página 20

MODELS 427 AND 427R INSTALLATION MODELS STAINLESS STEEL DOOR PANEL OVERLAY GLASS DOOR PANEL 427 | 427R 5 Before installing the stainless steel door panel, Inspect the door panel for the minimum /8" check the panel carefully. Options are available (16) thickness, the greater width requirements for kickplate/grille height, overall height, door for the stiles (to cover the door hinges), and swing and door lock. the finished inside edge. The door panel has a weight limit of 20 lbs (9 kg). See the Wi


Manuales de instrucciones similares
# Manual de instrucciones Categoría Descargar
1 Sub-Zero 424/O Manual de instrucciones Dosificador de bebidas 6
2 Sub-Zero 427R Manual de instrucciones Dosificador de bebidas 6
3 Sub-Zero 430/O Manual de instrucciones Dosificador de bebidas 1
4 Sub-Zero ICB424 Manual de instrucciones Dosificador de bebidas 2
5 Sub-Zero 424FS Manual de instrucciones Dosificador de bebidas 2
6 Sub-Zero ICB427 Manual de instrucciones Dosificador de bebidas 0
7 Sub-Zero WINE STORAGE Manual de instrucciones Dosificador de bebidas 9
8 Sub-Zero Sub Zero Wine Storage 315W Manual de instrucciones Dosificador de bebidas 0
9 Sub-Zero ICB427R Manual de instrucciones Dosificador de bebidas 1
10 Sub-Zero ICB424FS Manual de instrucciones Dosificador de bebidas 0
11 Sub-Zero ICB430 Manual de instrucciones Dosificador de bebidas 0
12 Sub-Zero WS-30 Manual de instrucciones Dosificador de bebidas 0
13 Sub-Zero 400 Series Wine/Storage Refrigerator 427RGLH Manual de instrucciones Dosificador de bebidas 0
14 Sony KDL-40V4100 Manual de instrucciones Dosificador de bebidas 4
15 Sony KDL-46V4100 Manual de instrucciones Dosificador de bebidas 2
16 Sony KDL-40W4100 Manual de instrucciones Dosificador de bebidas 3
17 Sony KDL-40V4150 Manual de instrucciones Dosificador de bebidas 2
18 Sony KDL-46W4150 Manual de instrucciones Dosificador de bebidas 1