Resumen del contenido incluido en la página 1
COOLER RCX-Z4
user manual
Resumen del contenido incluido en la página 2
COOLER RCX-Z4 user manual WARNING ! Improper Installation will result in damage to the processor. Never switch on the computer system until the fan is connected on to the motherboard power connector. 1
Resumen del contenido incluido en la página 3
COOLER RCX-Z4 user manual Installation Components A B C X 5 X 5 X 1 D E F X 2 X 2 X 1 G H I X 8 X 2 X 2 J K L X 4 X 6 X 1 M N O X 4 X 4 X 2 2
Resumen del contenido incluido en la página 4
COOLER RCX-Z4 user manual AMD K8 / AM2 Installation NOTE The K8 / AM2 heatsink retention bracket have been pre-installed on the heatsink. Do not remove for K8 / AM2. 1 Remove the retention module from the motherboard by removing the screws. 2 Keep the original motherboard backplate as it is. 3
Resumen del contenido incluido en la página 5
COOLER RCX-Z4 user manual 3 Stick the protective insulated O film onto the back of the heatsink retention brackets. 4 Apply the proper amount of thermal compound on the CPU surface, a thin film is ideal, extra thermal compound will not improve performance. Make sure the CPU surface is perfectly clean. FOR AMD K8 Place the RCX-Z4 on the top of the CPU, align two holes ( shown in red as the picture below ) of heatsink retention bracket with the Motherboard holes. Using the K8 screws wi
Resumen del contenido incluido en la página 6
COOLER RCX-Z4 user manual FOR AMD-AM2 Place the RCX-Z4 on the top of the CPU, align two holes ( shown in red as the picture below ) of heatsink retention bracket with the Motherboard holes. Using the K8 screws with M spring inserted, screwing down N into the motherboard backplate. D The RCX-Z4 is now installed on your K8-AM2 CPU See page 10-11 for the backplate fan controller and fan Installation 5
Resumen del contenido incluido en la página 7
COOLER RCX-Z4 user manual INTEL P4 LGA775 Installation 1 Remove the fan from the sink by unscrewing the four black screws. 2 Take off the pre-attached pair of K8-AM2 heatsink retention bracket; keep the four screws for the next 3 Attach both of the LGA775 heatsink retention brackets E to the heatsink base. 6
Resumen del contenido incluido en la página 8
COOLER RCX-Z4 user manual 4 Stick the protective insulated film onto the back of the heatsink C retention brackets. 5 K Place the screws through the J backplate into the head thread F of the screws , make sure the J correct four holes are used, as F shown in the diagram highlighted with red. Follow the same procedure for all four screws. K 6 Put the backplate with the screws fixed through the four motherboard holes as illustrated. 7
Resumen del contenido incluido en la página 9
COOLER RCX-Z4 user manual 7 Place the insulation washer B over the screws so they sit on the motherboard as shown. Follow the same procedure for all four screws. 8 Secure the backplate onto the motherboard by using the four G collars nuts . Turn these down onto the insulation washer, do not tighten one first, work around all four, gradually tightening them all. 9 Put the four rubber pads on A top of the four screws . G 8
Resumen del contenido incluido en la página 10
COOLER RCX-Z4 user manual 10 Apply the proper amount of thermal compound on the CPU surface, a thin film is ideal, extra thermal compound will not improve performance. Make sure the CPU surface is perfectly clean. 11 Place the cooler onto the four screws, secure the cooler with four more collars . G 12 Screw the fan onto the heatsink using the four black screws. The RCX-Z4 is now installed on your INTEL LGA 775 CPU See page 10-11 for the backplate fan controller and fan Installatio
Resumen del contenido incluido en la página 11
COOLER RCX-Z4 user manual For the backplate fan controller and fan Installation 1 Remove a PCI slot backplate and install the fan control unit. 2 Connect the fan cable with 3 pin connector to the Fan Controller Cable. 3 Connect the 3-pin connector of the Y fan cable assigned with a yellow and a black cable to the CPU fan motherboard connector. 10
Resumen del contenido incluido en la página 12
COOLER RCX-Z4 user manual 4 Connect the 3-pin connector with the yellow / red / black cable to the Controller Circuit board.. 5 Connect the power cable to the speed control and to the PSU 4-pin connector. Thank you for purchasing a quality Rosewill Product. Please register your product at : www.rosewill.com for complete warranty information and future support for your product. 11
Resumen del contenido incluido en la página 13
www.rosewill.com