Resumen del contenido incluido en la página 1
ATTACHMENT
OPERATOR’S
MANUAL
Clean Sweep
Twin Catcher
Clean Sweep Twin Catcher
Mfg. No. Description
1695168 Clean Sweep Twin Catcher
1733729
Rev. 03
Rev. Date 12/2006
TP 100-4404-03-AT-SMA
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
Table of Contents Safety Rules & Information General Warnings............................................2 Safety Decals ..................................................2 General Operating Instructions Before Operation .............................................3 Mowing with the Catcher .................................3 After Operation ................................................3 Storing the Grass Catcher...............................3 Initial Installation Hitch Installation .........
Resumen del contenido incluido en la página 4
Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. GENERAL WARNINGS � Know the unit’s controls and how to stop quickly. bag that meets manufacturer’s durability standards. READ THE OPERATOR’S MANUALS. � If the mower stall
Resumen del contenido incluido en la página 5
General Operating Instructions Before Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag is very important. For this reason, BEFORE YOU BEGIN MOWING you should make certain the underside of the mower and the u
Resumen del contenido incluido en la página 6
Initial Installation D B WARNING F Before beginning any service work turn off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). C Initial Installation C HITCH INSTALLATION A 1. Slide the 5/16-18 speed nut (A, Figure 1) onto rear frame support (E) through square hole (C) so that the D threaded side (B) is on the inside of tractor. E 2. Secure the 5/16-18 shoulder bolt (D) as shown. 3. Repeat on the other side. Figure 2. Frame Plate Reinforcement Instal
Resumen del contenido incluido en la página 7
Baffle Installation C B E A F A. Baffle (New) B. Spacer (New) C. Carriage Bolts, 5/16-18 x 2 (New) D. Locknuts, WHIZ Lock, D 5/16-18 (New) G E. Carriage Bolt, 5/16-18 x 5/8 (New) F. Wing Nut Assembly, Large, 5/16-18 (New) H G. Locknut, Center Lock, 5/16-18 (New) I J D H. Grass Shield (Existing) I. Blade, High Lift (New) K J. Hex Washer (Existing) L K. Washer (Existing) Torque Capscrew to L. Capscrew, 45-55 ft. lbs. (61-75 Nm) 7/16-14 x 1-1/4 (Existing) Figure 4. Baffle Assembly Baffle and
Resumen del contenido incluido en la página 8
Components Installation D B H C A D G E F A C F D Figure 8. Install Upright Support Figure 7. Install Pin and Bracket A. Hitch A. Lower Chute B. Upright Support B. Locknut, 1/4-20 C. Capscrews, 3/8-16 x 1 C. Puck, Metal D. Locknuts, 3/8-16 D. Capscrews, Thin Head, 5/16-18 x 3/4 E. Locknuts, 5/16-18 F. Bracket INSTALL UPRIGHT SUPPORT TO HITCH G. Defflector Prop H. Washer, 5/16 x 1/2 Dia. 1. Install the upright support (B, Figure 8) to hitch (A) and secure with 3/8-16 x 1 capscrews (C) and lock
Resumen del contenido incluido en la página 9
Support and Cover Installation B E C B D E A D C A D E C Figure 9. Install Bag and Cover Support A. Upright Support B. Bag and cover Support Figure 10. Install Cover Assembly C. Reinforcement Plate A. Bag Support Bracket D. Capscrews, 3/8-16 x 1 B. Cover Assembly E. Locknuts, 3/8-16 C. Cover Hinge Pins D. Hair Pins INSTALL BAG AND COVER SUPPORT E. Hinge Pivots 1. Install the bag and cover support (B, Figure 9) to upright support (A) using reinforcement plate (C) and INSTALL COVER ASSEMBLY 3/8
Resumen del contenido incluido en la página 10
Collector Bag Installation Bag, Chute and Tube Installation INSTALL COLLECTOR BAGS 1. Raise the cover (A, Figure 11). 2. Attach collector bags (B) using grass bag hanger (C) to bag hanger post (D). Note: It may be necessary to fold seat forward to allow cover to stay in the raised position. A D C B Figure 11. Install Collector Bags A. Cover B. Collector Bags C. Grass Bag Hanger D. Bag Hanger Post 8
Resumen del contenido incluido en la página 11
Install Latch & Hinge LOWER DISCHARGE CHUTE INSTALLATION A 1. Lift discharge deflector up (E, Figure 12). E 2. Slide the notch of bracket (G) on to deflector hinge G rod (F). 3. Secure the front of lower chute (A) to carriage bolt F (D) using wing nut (B). Note: Locknut (C) is intended to keep wing nut (B) B permanently on carriage bolt (D). C D CONNECTING DISCHARGE TUBE 1. Slide discharge tube (B, Figure 13) into seal (C). It may be necessary to lengthen several slits (F) in Figure 12. Insta
Resumen del contenido incluido en la página 12
Normal Removal & Installation Normal Removal & Installation A Collector Installation E Note: See previous pages for more detailed installation G and operation instructions if necessary. 1. Lift discharge deflector up (E, Figure 14). F 2. Slide the notch of bracket (G) on to deflector hinge rod (F). B 3. Secure the front of lower chute (A) to carriage bolt C (D) using wing nut (B). D 4. Mount the hitch support assembly (A, Figure 15) onto rear tractor frame. 5. Attach cover (B) to support assembl
Resumen del contenido incluido en la página 13
Normal Removal E F L J D C D A C B H K I A. Hitch Support Assembly H. Boot B. Cover I. Puck C. Pins J. Discharge Tube D. Hair Pins K. Wire Form E. Bag L. Seal F. Grass Bag Hanger Figure 15. Normal Installation & Removal Collector Removal 3. Remove and empty bags (E, Figure 15). 4. Lift discharge deflector up (E, Figure 14). WARNING 5. Loosen wing nut (B). OPERATION WITHOUT BAGGER 6. Slide lower chute (A) off carriage bolt (D) and deflector hinge rod (F). For operation without bagger, the mower
Resumen del contenido incluido en la página 14
MANUFACTURING, INC. Simplicity Mfg. Inc. 500 N Spring Simplicity Mfg. Inc. 500 N Spring Street / PO Box 997 Street / PO Box 997 Port Washington, WI 53074-0997 Port Washington, WI 53074-0997 www.AGCOLawn.com www.SimplicityMfg.com Simplicity Mfg. Inc. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.MasseyLawn.com Briggs & Stratton Yard Power Products Group Copyright © 2006 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved
