Resumen del contenido incluido en la página 1
4.9 CU.FT. BEER KEG COOLER
INSTRUCTION MANUAL
Model No.: MCKC490S
To ensure proper use of this appliance and your safety, please read the
following instructions completely before operating this appliance.
1
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS Names of the Parts _________________________________________________3 Important Safety Instructions ________________________________________ 4 Installation Instructions _____________________________________________ 4 Before Using Your Beer Dispenser____________________________________ 4 Installation of Your Beer Dispenser ________________________________ 4 - 5 Electrical Connection _______________________________________________ 5 Installation Instructions for
Resumen del contenido incluido en la página 3
NAMES OF THE PARTS MODEL NO.: MCKC490S 1 Beer Tower 2 Plastic Gasket 3 Safety Guard Rail 4 Drip Tray 5 Adjustable Thermostat 6 CO Regulator 2 7 CO Gas Cylinder 2 8 CO Gas Cylinder Support 2 9 Evaporator 10 Reversible Door 11 Beer Keg (not included) 12 Metal Plate 13 Metal Gasket(2) 14 Castors with Lock (4) 3
Resumen del contenido incluido en la página 4
IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of fire, electrical shock, WARNING or injury when using your Beer Dispenser, follow these basic precautions: • Read all instructions before using the unit. • DANGER or WARNING: Risk of child entrapment. • To avoid the possibility of child entrapment, please take the following precautions before throwing out the appliance. - Remove all doors from the unit. - Leave the shelves in plac
Resumen del contenido incluido en la página 5
electrical consumption. Extreme cold ambient temperatures may also cause the Beer Dispenser not to perform properly. This unit is not designed for outside installation (ie garages, porches etc.) • Avoid locating the Beer Dispenser in moist areas. • Plug the Beer Dispenser into an exclusive, properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and or grounding should be directed to
Resumen del contenido incluido en la página 6
INSTALLATION INSTRUCTIONS FOR BEER KEG Keg Installation Sketch · Install the four castors with lock provided into the unit’s bottom (four screw holes pre-supplied) The two metal gaskets are usded to the front two Castors. Figure (1) before installation. Figure (II) is the final version. GASKET (I) (II) 6
Resumen del contenido incluido en la página 7
Installation Of CO Cylinder Support 2 • Install the metal support provided onto the 4 studs located on the exterior back wall. Align the holes in the support with the studs and push down firmly. (See Figure 1) Installation Of CO Cylinder 2 • Install your fully charged cylinder into the support stand. Installation Of CO Regulator 2 • Attach the CO regulator to the cylinder by turning the regulator nut onto cylinder valve, making 2 sure washer is securely inserted into connecting n
Resumen del contenido incluido en la página 8
bottom cabinet. (See Figure 6) • Grasp the keg handles and slide it all the way into the cabinet. Fig. 4 Fig. 5 Fig. 6 Installation Of The Keg Coupler • Insert the keg coupler provided into the locking neck of the beer keg and turn it clockwise to lock into position, making sure the keg coupler is in the closed position. (See Figure 7) Installation Of The CO2 Air Line Hose • Attach the end of the air lin
Resumen del contenido incluido en la página 9
Spanner Faucet Wrench Spanner faucet wrench provided for either removing or tightening connection Plastic Faucet Lever Attach the black plastic lever (pull handle) provided on the top of the faucet tightening it by hand clockwise until the end, holding in the silver snug underneath so it does not move. If there is still a small drip from the faucet, you may have tightened the plastic lever too much and may need to unscrew silver snug counter- clockwise (as shown) one
Resumen del contenido incluido en la página 10
OPERATING YOUR BEER DISPENSER Setting The Temperature To start, turn the temperature control knob to the maximum setting (6). Allow the unit to run for 3 hours at the maximum setting. After 3 hours, adjust the temperature control to the desired setting. The range of temperature control is from position "1" the warmest to "6" the coldest Temperature range of the thermostat goes from 36°F to 45°F (2.2ºC to 7.2ºC).. Optimum temperature for serving draught beer is between 34°F – 38°F
Resumen del contenido incluido en la página 11
CHANGING THE REVERSIBLE DOOR This Beer Dispenser has the capability of either opening the door from the left or right side. The unit is delivered to you with the door opening from the left side. Should you desire to reverse the opening direction, please follow below instructions. Caution: To avoid personal injury to yourself and/or property, we ecommend that someone assist you during the door reversal process. 11
Resumen del contenido incluido en la página 12
CARE AND MAINTENANCE Cleaning Your Beer Dispenser • Turn the temperature control to "OFF", unplug the Beer Dispenser, and remove the contents. • Wash the inside surfaces with a warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water. • Wash the shelves and stand with a mild detergent solution. • Wring excess water out of the sponge or cloth when cleaning area of the controls, or any electrical parts. • Wash the outside cabine
Resumen del contenido incluido en la página 13
WARRANTY MC Appliance Corporation warrants each new Beer Keg Cooler to be free from defects in material and workmanship and agrees to remedy any such defect or to furnish a new part(s) (at the company’s option) for any part(s) of the unit that has failed during the warranty period. Parts and labor expenses are covered on this unit for a period of one year after the date of purchase. In addition, MC Appliance Corporation warrants the compressor (parts only) to be free from defects in
