Resumen del contenido incluido en la página 1
IMPORTANT MANUAL Do Not Throw Away
02478
OWNER'S MANUAL
WARNING:
Read this Owner's Manu al and follow all
MODEL:
Warnings and Safety Instructions. Fail ure
to do so can re sult in serious in ju ry.
PD22H42STB
LAWN TRACTOR
ALWAYS WEAR EYE PROTECTION DURING OPERATION
191897 03.15.04 RD
Printed in U.S.A.
Resumen del contenido incluido en la página 2
SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. DO NOT: I. GENERAL OPERATION Do not turn on slopes unless necessary, and then, Read, understand, and follow all instructions in the manual and on the machine before starting. turn slowly and gradually downhill, if possible. Only al
Resumen del contenido incluido en la página 3
SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. Be sure the area is clear of other people before mowing. Stop machine if anyone enters the area. WARNING: In order to prevent ac- ci den tal starting when setting up, Never carry passengers or children even with the blades off. trans
Resumen del contenido incluido en la página 4
CONGRATULATIONS on your purchase of a new tractor. PRODUCT SPECIFICATIONS It has been designed, engineered and manu fac tured to give GASOLINE CAPACITY 4.0 GALLONS you the best possible dependability and performance. AND TYPE: UNLEADED REGULAR Should you experience any problem you cannot easily rem- OIL TYPE (API-SF-SJ): SAE 30 (above 32°F) edy, please contact your nearest authorized service center/ SAE 5W-30 (below 32°F) department. We have competent, w
Resumen del contenido incluido en la página 5
UNASSEMBLED PARTS Seat Steering Wheel Steering Wheel Insert (1) Washer 17/32 x 1-3/16 x 12 Gauge (1) Knob Gauge Wheels Steering Extension Shaft Steering Sleeve (4) Clevis Pins (4) Wheels (4) Washers 3/8 x 3/4 x 14 Ga. Steering Adapter (4) Adjusting Bar (1) Large Flat Washer (4) Retainer Springs (4) Shoulder Bolt (double loop) (4) Locknut 3/8-16 (1) Oil Drain Tube (1) Locknut 1/2-20 Slope Sheet (1) Hex Bolt 1/4-28 x 1-1/4 (1) Locknut 1/4-28 (2) Keys 5
Resumen del contenido incluido en la página 6
ASSEMBLY Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. TOOLS REQUIRED FOR ASSEMBLY INSERT A socket wrench set will make assembly easier. Stan dard wrench sizes are listed. Utility knife Pliers 1/2 HEX NUT (1) 3/4" wrenches Tire pressure
Resumen del contenido incluido en la página 7
ASSEMBLY TO DRIVE TRACT OR OFF SKID (See Op- INSTALL SEAT (See Fig. 3) er a tion section for location and function of Adjust seat before tightening adjustment knob. con trols) Remove adjustment knob and fl at washer securing W ARNING: Before start ing, read, un der stand and fol low seat to cardboard packing and set aside for assembly all in struc tions in the Op era tion section of this manu al. Be of seat to tractor. sure tractor is in a well-ventilated area. Be sure the area in
Resumen del contenido incluido en la página 8
ASSEMBLY INSTALL MULCHER PLATE (See Figs. 4B) CHECK BRAKE SYSTEM Install two latch hooks to mulcher plate using screw, After you learn how to operate your tractor, check to see that washer, lock washer, and weld nut as shown. the brake is properly adjusted. See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual. NOTE: Pre-assemble weld nut to latch hook by in sert ing weld nut from the top with hook pointing down. ✓CHE CKLIST Tighten hardware securely. BEFOR
Resumen del contenido incluido en la página 9
OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean- ing. FAST IGNITION REVERSE NEUTRAL HIGH LOW SLOW CHOKE P LIGHTSON ENGINEON ENGINESTART PARKINGBRAKE ENGINEOFF PARKINGBRAKE PARKINGBRAKE LOCKED UNLOCKED FUEL OILPRESSURE BATTERY REVERSE FORWARD OVERTEMP MOWERHEIGHT MOWERLIFT LIGHT 15 15 ATTACHMENT ATTACHMENT SLOPEHAZARDS CLUTCHENGAGED CLUTCHDISENGAGED DANGER,KEEPHANDS KEEPAREACLEAR ANDFEETAWAY (SEESAFETYRULESSECTION) DA
Resumen del contenido incluido en la página 10
OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. IGNITION LIGHT AT TACHMENT SWITCH SWITCH CLUTCH LEVER AMMETER POSITION CHOKE CONTROL LIFT LEVER PLUNGER THROTTLE CONTROL ATTACHMENT LIFT LEVER CLUTCH/BRAKE PEDAL HEIGHT ADJUSTMENT KNOB PARKING BRAKE MOTION FREE WHEEL CONTRO
Resumen del contenido incluido en la página 11
OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per forming an y adjustments or repairs. We rec om mend a wide vision safety mask over spectacles or stan dard safety glasses. IMPORTANT:LEAVING THE IGNITION SWITCH IN ANY HOW TO USE YOUR TRACTOR POSITION OTHER THAN "OFF" WILL CAUSE THE BATTERY TO BE DIS CHARGED, (DEAD). TO SET PARKING
Resumen del contenido incluido en la página 12
OPERATION TO ADJUST GAUGE WHEELS (See Fig. 7) "ENGAGED" PO SI TION Gauge wheels are properly adjusted when they are slightly ATTACHMENT LIFT LEVER off the ground when mower is at the desired cutting height HIGH PO SI TION in operating position. Gauge wheels then keep the deck AT TACHMENT in proper position to help prevent scalping in most terrain CLUTCH LEVER conditions. LOW "DIS EN GAGED" POSITION PO SI TION NOTE:Adjust gauge wheels with tractor on a fl at level surface. Adjust mowe
Resumen del contenido incluido en la página 13
OPERATION Transmission Engaged CAUTION: Alcohol blended fuels (called gas o hol or using ethanol or methanol) can at- tract moisture which leads to sep a ra tion and forma tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before stor age of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel nex
Resumen del contenido incluido en la página 14
OPERATION AUTOMATIC TRANSMISSION WARM UP Slowly move motion control lever forward, after the Before driving the unit in cold weather, the trans mis sion tractor moves approximately fi ve (5) feet, slowly move should be warmed up as follows: motion control lever to reverse position. After the trac- tor moves approximately fi ve (5) feet return the mo- Be sure the tractor is on level ground. tion control lever to the neutral (N) position. Repeat Place the motion control lever in ne
Resumen del contenido incluido en la página 15
OPERATION MULCHING MOWING TIPS IMPORTANT: FOR BEST PERFORMANCE, KEEP MOWER HOUSING FREE OF BUILT-UP GRASS AND TRASH. CLEAN MAX 1/3 AFTER EACH USE. The spe cial mulch ing blade will recut the grass clip- pings man y times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biode- grade quick ly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will
Resumen del contenido incluido en la página 16
MAINTENANCE MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE SERVICE DATES Check Brake Operation Check Tire Pressure Check Operator Presence and Interlock Systems T R Check for Loose Fasteners 5 A Sharpen/Replace Mower Blades 3 C Lubrication Chart T Check Battery Level 4 0 Clean Battery and Terminals R Check Transaxle Cooling Check V-Belts Check Engine Oil Level Change Engine Oil (with oil filter) 1,2 Change Engine Oil (without oil filter) 1,2 E Clean Air Filter N 2 G Clean Air
Resumen del contenido incluido en la página 17
01202 MAINTENANCE TRACTOR MANDREL TRAILING ASSEMBLY EDGE UP Always observe safety rules when performing any main- BLADE te nance. CEN TER HOLE BRAKE OPERATION If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Ad just ments FLAT WASHER section of this manual). LOCK WASHER STAR TIRES Maintain proper air pressure in all tires (See “PROD UCT SPECIFICATIONS” section of this man
Resumen del contenido incluido en la página 18
MAINTENANCE NOTE: The original equipment battery on your tractor is NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid necessary. possible engine damage from running low on oil. TO CLEAN BATTERY AND
Resumen del contenido incluido en la página 19
MAINTENANCE CLEAN AIR SCREEN ENGINE OIL FILTER Air screen must be kept free of dirt and chaff to prevent Replace the engine oil fi lter every season or every other engine dam age from overheating. Clean with a wire brush oil change if the tractor is used more than 100 hours in or compressed air to re move dirt and stubborn dried gum one year. fi bers. MUFFLER CLEAN AIR INTAKE/COOLING AREAS Inspect and replace corroded muffl er and spark arrester To insure proper cooling, make sure the grass
Resumen del contenido incluido en la página 20
SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS Depress clutch/brake pedal fully and set parking brake. Place motion control lever in neutral (N) position. Place attachment clutch in “DISENGAGED” position. Turn ignition key to “STOP” and remove key. Make sure the blades and all moving parts have completely stopped. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. IMPOR
