Manual de instrucciones de Flymo Pac a Mow

Resumen del contenido incluido en la página 1

Pac a Mow
For all customer enquiries or for replacement parts, contact:-
☎ ☎ 0870 609 1901
www.flymo.com
customer.services@husqvarna.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference

Resumen del contenido incluido en la página 2

1 Carton Contents cable hook x 2 upper handle screw x 2 round headed barrel nut x 4 bolt x 2 electric cable with moulded cam lock x 4 on plug lower handle washer x 4 cable clip grassbox square headed bolt x 2 pivot block x 2 spring x 2 spanner instruction manual IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:- Husqvarna Outdoor Products Customer Service Department direct Telephone : 0870 809 1901 Safet

Resumen del contenido incluido en la página 3

2 there are signs of damage or ageing. 5. Mow across the face of slopes, never up and down. 3. Do not use the lawnmower if the electric cables are 6. Exercise extreme caution when changing direction damaged or worn on slopes. Walk never run. 4. Immediately disconnect from the mains electricity sup- 7. Mowing on banks and slopes can be dangerous. Do ply if the cable is cut, or the insulation is damaged. Do not mow on banks or steep slopes. not touch the electric cable until the electrical supp

Resumen del contenido incluido en la página 4

Assembly of Lower Handles to Lawnmower A1 A2 A3 A4 1. Insert the Square Headed Bolt into the lawnmower as 2. Place the Spring over the Bolt (A3) illustrated in fig A1. Then push the Bolt down until it is 3. Insert the Pivot Block on to the Bolt (A4) locked into position as illustrated in fig A2. B C1 C2 C3 pivot block lower handle x3 washer cam lock 4. Place the Lower Handle over the deck as illustrated in fig B. 6. Insert the Lower Handle, Washer and Cam Lock on 5. Insert the Barrel Nut into t

Resumen del contenido incluido en la página 5

D4 D5 D6 4. Fold down the Cam Lock towards the Handle as 5. The Cam Lock can be unlocked and locked as illus- illustrated in fig D4, and continue to turn clockwise trated in fig D6. (D5) until tightened. Repeat for the other side. E F G H 1 2 Attaching the Cable Hooks (for storage of the mains cable) The fixed cable from the switchbox to the motor can 1. Insert the post on the Cable Hook (E1) through the hole be attached to the handles using the clip on the Cable Hook (G) and with the Cable Clip

Resumen del contenido incluido en la página 6

Starting and Stopping M N P Q 1 To Start your Lawnmower R 1. Form loop in mains cable and push the loop through the slot. (M) 2. To secure, position loop over the hook and pull the cable back through the slot (N). 3. Connect plug to mains and switch on. 4. Tilt the handle downwards to slightly raise the front of the lawnmower and to reduce the risk of lawn Upper Handle and release the Lock-Off Button (R). damage whilst starting. 7. Lower the lawnmower to its proper operating posi- The switchbox

Resumen del contenido incluido en la página 7

Caring for your Lawnmower T Cleaning (T) the Fan and clean with a soft brush. • USE GLOVES 4. Wipe over the surface of your lawnmower with a dry cloth. • IMPORTANT It is very important that you keep your lawn- • IMPORTANT Never use water for cleaning your lawn- mower clean. Grass clippings left in any of the air intakes or mower. Do not clean with chemicals, including petrol, or solvents - some can destroy critical plastic parts. under the lawnmower could become a potential fire hazard. 1. R

Resumen del contenido incluido en la página 8

Fault Finding Hints Fails to Operate Excessive Vibration 1. Is the correct Starting procedure being followed? See 1. Disconnect from the mains electricity supply. ‘To Start your Lawnmower’ 2. Check that the Blade is fitted correctly? 2. Is the Power Turned On? 3. If the blade is damaged or worn, replace it with a new one. o 3. Check the fuse in the plug, if blown replace. 4. If vibration persists, turn the Blade through 180 by first loosening 4. Fuse continues to blow? the Blade Bolt, turning t

Resumen del contenido incluido en la página 9

EC Declaration of Conformity I, the undersigned M. Bowden of Husqvarna I, the undersigned M. Bowden of Husqvarna I, the undersigned M. Bowden of Husqvarna Outdoor Products, Aycliffe Industrial Park, Outdoor Products, Aycliffe Industrial Park, NEW- Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham. DL5 TON AYCLIFFE, Co. Durham. DL5 6UP Certify NEWTON AYCLIFFE, Co. Durham. DL5 6UP. Certify that the product:- that a sample of the above product has been 6UP Certify that a