Resumen del contenido incluido en la página 1
Operator's anual
T °
ZTS
Electric Start
Zero-Turn Rear Engine Riders with
Model No.
107.289920 (26HP Briggs & Stratton Engine with 52" Mower)
For answers to your questions about this
CAUTION: Before using this product, read
product, call:
the manual and follow all its Safety Rules
1-800-659-5917
and Operating Instructions,
Sears Craftsman Help Line
5 am- 5 pm, Mon - Sat
Nota: Una traducci6n en espaSol de este Manual
del Operador puede encontrarse en la pagina 39.
U.S.A.
Sears, Roebuck and Co., H
Resumen del contenido incluido en la página 2
2
Resumen del contenido incluido en la página 3
Warranty Statement ..................................................... 3 Storage ....................................................................... 36 Safety Rules & Information ......................................... 4 Specifications ............................................................ 36 Identification Numbers ................................................ 9 Troubleshooting ......................................................... 37 Assembly ................................
Resumen del contenido incluido en la página 4
Readthesesafetyrulesandfollowthemclosely. Failure to obeytheserulescouldresultinlossofcontrol of unit,severepersonal injuryordeathtoyou,orbystanders, ordamage to property orequipment. This mowing deck is capable of amputating hands and feet and throwing objects. The triangle _ in text signifies important cautions or warnings which must be followed. 19. Follow the manufacturer's recommendations for wheel GENERAL OPERATION weights or counterweights. 1. Read, understand, and follow all instructions
Resumen del contenido incluido en la página 5
SLOPE OPERATION ,WARNING Slopes are a major factor related to loss-of-controland tip- Never operate on slopes greater than 17.6 percent over accidents, which can result in severe injury or death• (10°) which is a rise of 3-1/2 feet (106 cm) vertically in Operation on all slopes requires extra caution• If you cannot 20 feet (607 cm) horizontally. back up the slope or if you feel uneasy on it, do not operate Select slow ground speed before driving onto slope. on it. Use extra caution when operat
Resumen del contenido incluido en la página 6
SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION ONLY RiDE UP AND DOWN HILL, NOT ACROSS HiLL o_ 10 DEGREES MAX. WARNING: To avoid serious injury, operate your unit up and down the face of slopes, never across the face. Do not operate on slopes greater than 10 degrees. Make turns gradually to prevent tipping or loss of control. Exercise extreme caution when changing direction on slopes. Braking may be affected by attachments. Reduce speed on slopes. 1. Fold this page along dotted line indic
Resumen del contenido incluido en la página 7
SERVICE AND MAINTENANCE 13. If the fuel tank must be drained, it should be drained outdoors. Safe Handling of Gasoline 14. Replace faulty silencers/mufflers. 1. Extinguish all cigarettes, cigars, pipes, and other 15. Maintain or replace safety and instruction labels as sources of ignition. necessary. 2. Use only approved gasoline containers. 16. Use only fac!ory authorized replacement parts when 3. Never remove the gas cap or add fuel with the engine making repairs. running. Allow the engine to
Resumen del contenido incluido en la página 8
SAFETY & OPERATION DECALS read and obeyed. Personal bodily injury can result when This unit has been designed and manufactured to pro- these instructions are not followed. The information is for vide you with the safety and reliability you would expect your safety and it is important! The safety decals below from an industry leader in outdoor power equipment are on your rider and mower. manufacturing. Although reading this manual and the safety instructions If any of these decals are lost or dam
Resumen del contenido incluido en la página 9
_(\_\_' CRAFTSMAN _ When contacting the service center for replacement parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer's identification numbers, and engine serial numbers in the space provided for easy access. The identification tag is located on the underside of the seat. Tilt the seat forward to access the ID tag. Model Description Name/Number For answers to your questions about this product, call: 1-800=659=5917 Stock Number Unit Serial
Resumen del contenido incluido en la página 10
INSTALLING THE SEAT 3. Secure the seat to the seat base with two 5/16-18 x 3/4 serrated head bolts for the rear seat slots, and 1. Raise the seat base (see Figure 1). two 5/16-18 x 3/4 shoulder bolts for the front slots. 2. Align the holes in the seat bottom with the holes in 4. Tighten to 14-19 ft-lbs (19-25 Nm). the seat base. / J 19-25 Nm 14-19 ft-lbs 5/16-18 x 3/4 5/16-18 x 3/4 Figure 1. Installing the Seat 10
Resumen del contenido incluido en la página 11
INSTALLING THE SEAT SAFETY SWITCH 1. Squeeze the side clips of the safety switch (A, Figure 2), and insert the switch into the slot (B) in the seat bottom. Be sure to slide the switch fully forward. 2. Connect the harness terminal housing (C) to the seat switch. , Loop the wire tie (D) around both the switch body and the terminal housing. t t t Figure 2. Installing the Seat Safety Switch 11
Resumen del contenido incluido en la página 12
3. Install the hardware as shown in Figure 3. Tighten to SETTING UP THE GROUND SPEED 15-17 ft-lbs (20-23 Nm). CONTROL LEVERS NOTE: Ground speed control levers must be adjusted 1. Loosen (do not remove) the hardware securing the prior to use. Refer to the "Ground Speed Control ground speed control levers to the lever bases (see Adjustment" section. Figure 3). 2. Raise the levers, aligning the upper hole in each lever with the upper slotted hole in the lever base. _ 5/16-18 (_ (_ 5/16-18 x 1-3/4 2
Resumen del contenido incluido en la página 13
3. Insert the hinge rod (D) through one end of the INSTALLING THE SIDE DISCHARGE deflector assembly and hinge, through the torsion DEFLECTOR spring, and out through the other end of the deflector assembly and hinge. NOTE: The deflector hinge (A, Figure 4) and bracket (B) come installed on the mower deck from the factory. NOTE: Make sure that the shorter end of the torsion spring (E) hooks into the notch of the deflector bracket (F). AWARNING 4. Firmly install one push nut (G) onto each side of t
Resumen del contenido incluido en la página 14
Remove the Packaging Materials Fill=Up with FRESH Gasoline Remove the cardboard from the crate. Lift the seat deck to access the _ Ea fuel cap and tank. Remove any steel branding securing the unit to the crate. Locate the manual packet. the tank with fresh fuel. After _ emove the fuel tank cap and fill fueling, securely install the cap Read the Operator's Manual and wipe up any fuel that may Locate the operator's manual in the have spilled. See the Operator's Manual for fuel manual packet. You s
Resumen del contenido incluido en la página 15
Left Right @ GroundSpeed & I _" ControlLever ParkingBrake r Lever L Ground Speed Levers- Ground Speed Levers- DRIVE P0sitons START/PARK P0sitons ParkinBrake Lever- P EHGAGE Pesiton Fu CONTROL FUNCTIONS __ The information below briefly describes the function of individual controls. Starting, stop- ping, driving, and mowing require the combined Transmission ReleaseLevers Mower Blade use of several controls applied in specific Switch sequences. To learn what combination and sequence of controls to
Resumen del contenido incluido en la página 16
Mower Cutting Height Switch _ Mower Blade Switch To increase the mower cutting height (raise the mower The yellow mower blade switch turns the mower blades deck), press the top of the yellow cutting height switch. on and off. To turn the mower blades ON, pull the switch To decrease mower cutting height (lower the mower up. To turn the mower blades OFF, push the switch down. deck), press the bottom of the switch. Mower cutting Always set the engine speed control to FAST before turn- height range
Resumen del contenido incluido en la página 17
CHECKS BEFORE STARTING • Check that the crankcase oil is filled to full mark on dipstick. • Fill the fuel tank with fresh fuel. FUEL RECOMMENDATIONS For daily operation: Use only unleaded gasoline with a pump sticker octane rating of 87 or higher. Gasohol (up to 10% ethyl alcohol, 90% unleaded gasoline by volume) is approved as a fuel. Methyl Teriary Butyl Ether (MTBE) and unleaded gasoline blends (up to a maximum of 15% MTBE by volume) are approved as a fuel. No other gaso- line/alcohol or gaso
Resumen del contenido incluido en la página 18
EMERGENCY STOPPING PUSHING THE RIDER BY HAND In the event of an emergency the engine can be stopped NOTE: Do not disengage the transmission ff parked on a by simply turning the ignition switch to STOP. Use this slope method only in emergency situations. For normal engine , Turn the mower blades OFF, push the ground speed shut down follow the procedure given in STOPPING THE control levers out to their START/PARK positions, RIDER AND ENGINE. engage the parking brake, turn the ignition switch OFF,
Resumen del contenido incluido en la página 19
Smooth Travel DRIVING PRACTICE - The lever controls of the BA SiC DRIVING zero turn rider are WARNING: Never operate on slopes greater than 17.6% highly responsive. (10°). See SLOPE OPERATION in the safety section. The BEST method of Zero turn riders operate differently from other four- handling the ground wheeled vehicles. The drive wheels are also your steer- speed control levers is in ing wheels. If you cannot drive the unit on a hill, you will three steps - as shown not be able to steer the
Resumen del contenido incluido en la página 20
Practice Turning Around a Corner Practice Turning In Place While traveling forward allow one handle to gradually To "zero turn" means to turn in place. To turn in place, return back toward neutral (see Figure 12). Practice sev- gradually move one ground speed control lever forward from neutral and one lever back from neutral simultane- eral times before mowing. ously (see Figure 13). Repeat several times. NOTE: To prevent damaging your lawn by pivoting direct- ly on the tire tread, it is best to
