Resumen del contenido incluido en la página 1
OWNER’S MANUAL
®
BATTERY CHARGER
50/15/2 Amp
Manual
ENGINE STARTER
With Battery Tester and
Air Compressor
225/125 Amp
Model No.
200.71233
CAUTION:
Read all Safety Rules and Operating Instructions,
and follow them with each use of this product.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
00-99-000538/0506
Resumen del contenido incluido en la página 2
Table Of Contents Warranty .................................................................... 1 Using Your Battery Charger..................................... 7 Important Safety Instructions ................................. 2 Setting the controls .............................................. 7 Parts .......................................................................... 3 Using the compressor .......................................... 9 Wiring Diagram ....................................
Resumen del contenido incluido en la página 3
Important Safety Instructions – SAVE THESE INSTRUCTIONS – To reduce the risk of explosion, explosive gases, or injury while WARNING using your battery charger, follow the precautions listed below: � Read all instructions and cautions printed on the � Do not disassemble charger. Take it to a battery charger, battery, and vehicle or equipment qualified service professional if service or repair using battery. is required. Incorrect assembly may result in fire or electrical shock. � Use charger only
Resumen del contenido incluido en la página 4
Parts This section shows an illustration of your battery charger. Use it to become familiar with where all the parts are located, and what they look like. 13 1 Replacement Parts List DieHard 71233 ITEM DESCRIPTION PART NUMBER 2 1 Handle 3599000286 2 3899001519 Positive (RED) Cable w/clamps 3 3899001520 Negative (BLACK) Cable w/clamps 4 5 4 Power Cord 90026140 2299001478 5 Compressor Hose Assembly 3 6 2299001479 6 Compressor 7 Circuit Breaker 3999000110 7 8 8 2299001470 Power Board/Heatsink Assem
Resumen del contenido incluido en la página 5
Before Using Your Battery Charger It is important to prepare your charger for use. This section will tell you how to assemble the charger, ground and connect the power cord, and prepare to charge a battery. Assembling your charger It is important to fully assemble your charger before use. Follow these instructions for easy assembly. PARTS: TOOLS NEEDED: Two, 10-32 thread cutting 3/8" wrench screws (for mounting foot) Two, 1/4-20 thread cutting 5/16" wrench screws (for wheels) Two wheels Hammer O
Resumen del contenido incluido en la página 6
Axle Assembly (continued): Place the charger on its side. Place one end of each bracket into slot, then place the axle assembly under each bracket. Fasten the other side of each bracket using the two, 10-32 thread cutting screws provided. Handle: Turn the charger right side up onto its foot and wheels. Remove the two top screws from each side of the charger. Align the handle so the screw holes are aligned with the screw holes on each side of the wheel charger. Attach handle using the same screws
Resumen del contenido incluido en la página 7
Using an extension cord The use of an extension cord is not recommended. If � Use the recommended minimum AWG (American you must use an extension cord, please make sure Wire Gauge) to be sure that wire size is large that you follow these guidelines: enough for the rating of the charger. � Make sure the pins on the plug of the extension cord are the same number, size, and shape as those of MINIMUM RECOMMENDED EXTENSION CORD the plug on the charger. Length of Cord, in Feet 25 50 100 150 � Use only
Resumen del contenido incluido en la página 8
Using Your Battery Charger To obtain the best results from your battery charger, you must know how to use it properly. This section tells how to set the controls and how to charge a battery in and out of the vehicle. Setting the controls Follow these instructions to obtain the accurate charge BATTERY TEST level for your battery. The Battery Test is based on the terminal voltage of the battery. If the battery is installed in the vehicle, TOUCH PAD CONTROLS AND DIGITAL DISPLAY make sure the engine
Resumen del contenido incluido en la página 9
3. Connect the battery charger as outlined in “Charg- 12V ALTERNATOR/GENERATOR DISPLAY 14 – 15 volts = Good condition ing Your Battery” on page 10. The voltage will be displayed. 12.8 or less volts = Check with qualified technician NOTE: If a battery has recently been charged or in a vehicle that has been run recently, turn on the 12.8 - 14 volts or = See vehicle owner’s 15 volts or more manual vehicle’s headlights for a few minutes before reading the meter to avoid getting a false reading NOTE:
Resumen del contenido incluido en la página 10
Using the compressor CAUTION – Read instructions of the product being 4. The air compressor will run for a maximum of 15 inflated before using the compressor. Avoid over minutes or it may automatically shut down sooner inflation, do not exceed the manufacturer’s recom- if a high load causes it to overheat. It will then cool mended pressures. Do not leave the air compressor for 20 minutes. The digital display will read HOT. unattended during use. After 20 minutes, the air compressor will automa
Resumen del contenido incluido en la página 11
Charging Your Battery NOTE: A marine (boat) boat battery must be removed To charge a positive grounded post system: and charged on shore. To charge it on board requires Connect the black (NEGATIVE) battery charger equipment specially designed for marine use. clamp to the NEGATIVE (NEG,N,–) ungrounded post of the battery. Then connect the red (POSI- Charging your battery in the vehicle: TIVE) clamp to a heavy unpainted metal part of 1. Arrange the power cord and charging cords care- the chassis o
Resumen del contenido incluido en la página 12
5. Take the other end of the 6-gauge (AWG) insu- Charging your battery outside the vehicle: lated battery cable (at least 24-inches in length), NOTE: A marine (boat) must be removed and charged and, standing as far away from the battery as on shore. To charge it on board requires equipment possible, connect the black (NEGATIVE) charger specially designed for marine use. clamp to the free end of the cable. Be sure to rock 1. Remove battery from vehicle, making sure to dis- the clamp back and fort
Resumen del contenido incluido en la página 13
Calculating charge times The Chart Method � Marine, or deep-cycle batteries are usually rated in Use the following table to more accurately determine Reserve Capacity (RC). the time it will take to bring a battery to full charge. First, identify where your battery fits into the chart. � NR means that the charger setting is NOT RECOM- MENDED. � Small batteries — motorcycles, garden tractors, etc. — are usually rated in Ampere Hours (AH). For Find your battery’s rating on the chart below and note
Resumen del contenido incluido en la página 14
Troubleshooting Performance problems often result from little things that you can fix yourself. Please read through this table for a possible solution if a problem occurs. PROBLEM POSSIBLE CAUSE SOLUTION/REASONS No reading on Digital AC cord and/or extension Check AC outlet and extension cords for loose fitting Display, charger fan cord is loose. plug. not working. Poor electrical connection. Check for open fuse or circuit breaker supplying AC outlet. No reading on Digital Battery severely Conti
Resumen del contenido incluido en la página 15
For information about troubleshooting, call toll-free from anywhere in the U.S.A. 7 am to 4:30 pm Central Time Monday through Friday. 1-800-SEARS-64 (1-800-732-7764). 14
