Resumen del contenido incluido en la página 1
VERSA E3100
Disassembly Manual
Resumen del contenido incluido en la página 2
Table of contents Overview................................................................................................................................................................3 Technician Notes..................................................................................................................................................3 Disassembly Instructions.......................................................................................................................
Resumen del contenido incluido en la página 3
Overview This document contains step-by-steps disassembly instructions for VERSA E3100 notebook. The instructions explained how to remove or disassemble a particular part with the help of photos. The size of the screws in used is display on the right side of the guide. NEC reserves the right to make any changes to this disassembly guide without notice. Technician Notes Only technician/engineer authorized by NEC Computer Asia Pacific should attempt to repair this equipment. All troub
Resumen del contenido incluido en la página 4
WARNING Hazardous Voltage Ensure that the computer disconnected from its There is hazardous voltage present inside the computer power source and from all telecommunications when it is connect to an AC supply, even when the links, networks, or modem lines whenever the computer’s power switch is off. Exposure to hazardous chassis cover is remove. Do not operate the voltage could cause personal injury. To avoid risk of injury, computer with the cover is removed. contact an Authorized
Resumen del contenido incluido en la página 5
NEC VERSA E3100 Disassembly Manual Page 5
Resumen del contenido incluido en la página 6
Removing the Battery Perform the following steps to remove the battery: 1. Make sure to power off the VERSA E3100 2. Turn the unit upside down. 3. Unlock the battery and slide it out of its place as the arrow shows in Fig. 1 Fig. 1 Removing the battery NEC VERSA E3100 Disassembly Manual Page 6
Resumen del contenido incluido en la página 7
Removing the Memory and Wireless LAN Module To remove the Memory and Wireless LAN Module, first remove the battery (see Removing the Battery), then perform the following steps: 1. Release the two screws retaining the memory and wireless LAN module cover. Fig. 2 Removing the screws retaining the memory and wireless LAN module slot cover 2. Remove the two wireless LAN cable and unclip the memory and wireless module as shown
Resumen del contenido incluido en la página 8
Removing the Hard Disk Drive To remove the hard disk drive, first remove the battery (see Removing the Battery), then perform the following steps: 1. Remove the screws as shown in Fig. 4 M2.5X4.5 Black Fig. 4 Removing the Hard disk drive cover 2. Release the screws that secure HDD module as shown in Fig. 5 and carefully pull the HDD module out from the base unit. M2.5X6.5 Black
Resumen del contenido incluido en la página 9
Removing the Optical Disk Drive To remove the ODD, first remove the battery (see Removing the Battery) then perform the following steps: 1. Remove the screws retaining the optical drive as shown in Fig. 6 M2.5X6.5 Black Fig. 6 Releasing the optical drive 2. Eject the optical drive using pin as shown in Fig. 7 Fig. 7 Ejecting the optical drive
Resumen del contenido incluido en la página 10
3. Pull the ODD module out from the base unit as shown in Fig. 8 Fig. 8 Pulling the optical drive out from the base unit NEC VERSA E3100 Disassembly Manual Page 10
Resumen del contenido incluido en la página 11
Removing the Keyboard To remove the Keyboard, first remove the battery (see Removing the Battery), then perform the following steps: 1. Unscrew the keyboard cover from the rear of the system as shown in Fig. 9 M2.5X4.5 Black Fig. 9 Releasing the keyboard cover 2. Lift up the keyboard cover carefully as shown in Fig. 10 Fig. 10 Lifting up the Keyboard Cover 3. Unscrew the two keyboard screws
Resumen del contenido incluido en la página 12
4. Turn the system over, remove another screw as shown in Fig. 12 M2.5X6.5 Black Fig. 12 Removing the screw at the bottom of the notebook 5. Lift up the keyboard and disconnect it from the base system as shown in Fig. 13 Fig. 13 Removing the keyboard flex cable NEC VERSA E3100 Disassembly Manual Page 12
Resumen del contenido incluido en la página 13
Removing the LCD Module To remove the LCD Module first remove the battery (see Removing the Battery) and remove the Keyboard (see Removing the Keyboard) then perform the following steps: 1. Turn the system over and slowly push the wireless LAN cable as shown in Fig. 14 Fig. 14 Pushing the Wireless LAN cable to the front of the system
Resumen del contenido incluido en la página 14
2. Turn the notebook back, a) remove the two tape b) disconnect the LCD cable from the connector c) unscrew the 4 screws all these steps is as shown on Fig. 15 M2.5X6.5 Black Fig. 15 Steps to remove LCD Module 3. Gentle removes the LCD module.
Resumen del contenido incluido en la página 15
Removing the LCD Panel To remove the LCD panel, first remove the LCD module (see Removing the LCD Module), then perform the following steps: 1. Use a pin to remove the rubber cover on the LCD module as shown in Fig. 16 2. Remove all screws as shown in Fig. 16 and carefully remove the LCD cover. M2.5X6.5 Black Fig. 16 Removing the rubber covers & screws on the LCD Module 3. Remove the cables attach
Resumen del contenido incluido en la página 16
4. To remove the LCD, remove the 4 screws as shown in Fig. 18 M2.5X4.5 Black Fig. 18 Removing the LCD panel NEC VERSA E3100 Disassembly Manual Page 16
Resumen del contenido incluido en la página 17
Removing the Switch Board Module To remove the Switch Board Module first remove the battery (see Removing the Battery) and remove the Keyboard (see Removing the Keyboard) then perform the following steps: 1. Unscrew the screw on the switch board and detached the flex cable as shown on Fig 19. M2X4 Silver Fig. 19 Uninstalling the switch board
Resumen del contenido incluido en la página 18
Removing the Top Cover Assembly To remove the Top Cover Assembly first remove the battery (see Removing the Battery), remove the Keyboard (see Removing the Keyboard) and remove the LCD module ( See Removing LCD module) then perform the following steps: 1. Remove a screw and the three cables as shown on Fig 20. M2.5X6.5 Black Fig. 20 Removing a screw and 3 cables
Resumen del contenido incluido en la página 19
2. Turn the system over and remove all the 14 screws as shown on Fig 21 M2.5X6.5 Black Fig. 21 Remove all the 14 screws 3. Turn the system back; slowly remove the top cover assembly as shown in Fig 22. Fig. 22 Removing the screws retaining the Heat Plate NEC VERSA E3100 Disassembly Manual Page 19
Resumen del contenido incluido en la página 20
Removing the Main Board To remove the Main Board, first remove the Top Cover Assembly (see Removing Top Cover Assembly) then perform the following steps: 1. Remove the 6 screws and detached the three connectors as shown on Fig 23 M2.5X4.5 Black Fig. 23 Removing screws and the connectors on the main board 2. Remove the two hex screws from the VGA port as shown in Fig. 24 M2.5X5 Silver
