Resumen del contenido incluido en la página 1
I SECURITY GUARD STATION 1
INSTALLATION & OPERATION MANUAL
PRECAUTIONS
6. Do not install the unit in any of the following locations, as
A WARNING (Negligence could result in death or serious
it may cause the system to malfunction;
injury to people.)
- High or extreme cold temperature area: under direct sunlight,
1. Do not open the unit case. 8
near equipment that varies in temperature, in front of air
2. Do not dismantle or alter the unit. Fire or electric shock
conditioner, inside a
Resumen del contenido incluido en la página 2
PROGRAMMING /R While being programmed, PANIC CALL is not receivable on GF-MK, Enter Program Mode Select Menu & Quit 1 LCD YOUR OPERATION LCO YOUR OPERATION ......................................... 1 1 AIPHONE + @ @aaaa I - a INITIAL ID CODE MFNi I .- J I 1 SELECTLANGUAGE -b 2 CHANGE ID CODE + 3 RESIDENCE INFO. . + I INITIAL ID CODE @ PGO to Menu 1-5 DECIDE & NEXT @) - Standby DEClDt% BACK I ID CODE = @ + 4 digit Menu 1 : Select language Menu 2: Change ID code LCD YOUR OPER
Resumen del contenido incluido en la página 3
Menu 5: Programming << ,&, While connecting date to the system, whole system is not operatable including PANIC CALL. Before initiating PROG~MMING << operation, make sure ROOM number has been programmed on Menu RESIDENCE INFO. +@ . DECIDE & NEXT J -+ Lift the handset (Security Guard Station) J Programming Step 4 At an Residential Station number I, lift handset. Communication channel is established. 1 With Scroll buttons, have the assigned Name displayed, and press @ button Hearin
Resumen del contenido incluido en la página 4
VVITH RESIDENTIAL STATION Calling a Residential Station At Security Guard Station . At Residential Station Call tone sounds for Lift the handset to reply within 4 When finished, hang up handset. Lift the handset, have the name i Communication will automatically ’ displayed, and press Call button. i 2 approximately 10 approximately 45 seconds. seconds. Communicate with the turn off in approximately 2.5 (See below) Security Guard Station. minutes. * + + Note: See “IN USE” is not display
Resumen del contenido incluido en la página 5
WITH ENTRANCE STATION Receiving a call from Entrance Station Requires name registration and linkage. At Security Guard Station At Entrance Station 1 Momentarily depress While communicating, a Call button. Door Release Muted call tone is heard from the 3 4 Entrance Station. Momentarily depress DOOR At the communicating RELEASE button. entrance station, door release is activated. + DOOR RELEASE When finished, hang up the handset. 1 button Communication will automatically turn o
Resumen del contenido incluido en la página 6
BETVVEEN SECURITY GUARD STATIONS At Calling Station 1 Lift the handset, press @, @ buttons. Press @ button, and CALL button. Muted call tone is heard from handset receiver. Notes: See “IN USE” is not displayed at start of operation. ‘When entering@ only, the message is ENTER A LETTER, as is common operation entering an alphabet in searching name as well, *When no Security Guard Station is registered, a message NO ENTRY comes on. PANIC CALL At Securiw Guard Station i At Residential Sta
Resumen del contenido incluido en la página 7
MOUNTING Desk-top mounting on GFW-S stand 2. Attach mounting bracket to 3. Connect wires on terminal block, putting wires neatly in the slot. 1. Separate mounting bracket on back of the unit. GFW-S stand as shown. 4. Place protection cover on terminal section. GFW-S (not included) Wall-mounting Notes; It is suggested to mount the station so that the LCD display comes at the user's eye level. Mounting I U;lplug Slide and pull out the terminal block. Strip cable jackets, and put all
Resumen del contenido incluido en la página 8
TECHNICAL PRECAUTIONS Ambient temperature: 0°C-40°C (+32"F-+104"F). Asking for repairs: In case the unit does not operate properly, ask qualified technician to repair it. Cleaning: Clean the equipment with a soft cloth dampened with neutral household cleanser. Never use any abrasive cleaner or cloth. I Adjusting call tone volume; Setting switches; DIP switches bank (SW1) GF-MK GF-MK Back view When you forgot your ID code .- t '.-*' Call tone volume control _..... I The IDcode ret
