Manual de instrucciones de Draper 220V SL

Resumen del contenido incluido en la página 1

Installation/Operating Instructions
220V SL & SLX Scissor Lift Video Projector Lift by Draper
These Installation/Operating Instructions are available in the offi cial language
➂ Fastening methods must be suitable for mounting surface, and se cure ly
of the country where you purchase the product. Please contact your
anchored so that vibration or abusive pulling on unit will not weaken
distributor to request a copy.
installation.
Vous pourriez demander les instructions d’installation et d’opé

Resumen del contenido incluido en la página 2

220V Scissor Lift by Draper page 2 of 6 Installing Projector Installing Optional Plenum Housing The Plenum Housing is shipped in pieces, and must be assembled by the Depending on job conditions and projector, it may be easier to re move installer. The height of the plenum can be adjusted by up to 2" (5 cm) by moving optional ceiling closure panel before installing projector. the trim frame to different mounting holes in side panels. It is recommended that Generally, the video pro jec tor

Resumen del contenido incluido en la página 3

220V Scissor Lift by Draper page 3 of 6 Installing Optional Ceiling Closure Panel—"B", "S", "E", "J" If your Scissor Lift is equipped with a "B" or "E" ceiling closure panel, it can be Optional Ceiling Closure for Scissor Lift used as is, or in conjunction with a piece of existing ceiling tile. ➀ If installing with ceiling tile, you may need to cut tile so its overall dimensions are the same as (or slightly less than) the closure panel. Place tile into trim frame. Lay closure panel on top

Resumen del contenido incluido en la página 4

750 mm 679 mm 220V Scissor Lift by Draper page 4 of 6 SL Series 585 mm 597 mm 528 mm 528 mm Scissor Lift Dimensions Maximum Lowering Retracted 1 15 mm dia. Model Distance Height mounting holes SL4 122 cm 21 cm SL5 152 cm 24 cm See chart (shown slightly SL6 183 cm 26 cm lowered) SL7 213 cm 29 cm SL8 244 cm 31 cm Space for Fail-safe inertial projector's safety belt system SL9 274 cm 33 cm ceiling Space for projector mounting SL10 305 cm 36 cm Pair of 5 mm aircraft cables bracket

Resumen del contenido incluido en la página 5

10A 220V Scissor Lift by Draper page 5 of 6 www.draperinc.com (765) 987-7999 Dashed wiring by electrician Transformer L1 RED BK WH BLUE N Transformer GRD Fuses and fuse clips BK YW provided by Draper are located in the electrical YW box (also provided). BK WH BEBK BK Capacitor 12 34 5 6 78 910 YW 3 x 3 Up Relay Down Relay Connection BE BE BE NC NC Board BE GN NO RD NO BK Motor RD BE COM RD COM BK RD RD RD (-) (+) (-) (+) 12 34 5 6 78 910 BK RD BE BE BK RD BK BK BK RD BK BK BK GN 6 Conductor Modu

Resumen del contenido incluido en la página 6

220V Scissor Lift by Draper page 6 of 6 Adjusting Show Position (Up to Standard Position) ➀ Find the empty slot in the bottom of the top pan of lift (the only empty slot). ➁ Use the open-end wrench (provided) Front of Unit ➂ Find the threaded coupling (long nut) just inside the top pan (through the slot). ➃ Push wrench toward rear of unit to lower. ➄ Pull wrench toward front of unit to raise. Increase Show Position Decrease Show Position (Stops Lower) (Stops Higher) Front Rear Show Position Ad