Manual de instrucciones de American Standard Princeton 4508.801

Resumen del contenido incluido en la página 1

Installation
Instructions
PRINCETON
4508.801
Spread Lavatory Faucet with
Speed Connect™ Drain
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
Speed Connect™ Drain*
Certified to comply with ANSI A112.18.1
• Fewer parts, installs in less time
M968832 Rev.1.3
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
To ensure that your installation proceeds smoothly-please read these

Resumen del contenido incluido en la página 2

POP-UP DRAIN 2 Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). 1 Remove CARDBOARD SPACER (2) from under DRAIN BODY DRAIN POP-UP (3). 3 Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 2 4 REMOVE FLANGE Fig. A. Fig. B. 3 1 Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against LOCKNUT (3). Fig. B. 4 2 3 INSTALL DRAIN FROM TIGHTEN LOCKNUT REAR

Resumen del contenido incluido en la página 3

ATTACH CABLE CONNECTOR 7 Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and 1 hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig. B. 2 1-1/4” O.D. CHECK OPERATION OF POP-UP 8 Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes. 1 Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions. 2 MAKE WATER SUP

Resumen del contenido incluido en la página 4

INSTALL HANDLES 10 Push ADAPTER (1) on VALVE STEM (2), so that the hole of the ADAPTER (1) without a spline is facing up. See figure "A". Tighten THREAD ON STEM SCREW (3) to secure ADAPTER (1). TO DECK ADAPTER 4 Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting male teeth on ADAPTER (1) to female teeth in HANDLE (4). TOP Thread LEVER HANDLE ASSEMBLY (4) onto DECK ADAPTER (5) 1 until snug against mounting surface. 3 Figure "A" 2 SPLINE END DOWN 5 TEST INSTALLED FITTING 11 5 With HAN

Resumen del contenido incluido en la página 5

Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: • Follow STOPPER REMOVAL PROCEDURE. If you would like the ability to remove your Stopper simply by lifting it out of the drain: • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode. C

Resumen del contenido incluido en la página 6

STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable). Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice Fig. G. that the Loop is on one side of the Stopper. Fig. G. To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the LOGO Sink and the American Standard logo is facing front. Rotate Stopper s

Resumen del contenido incluido en la página 7

PRINCETON Spread Lavatory Faucet with Pop-up Drain MODEL NUMBER 4508.801 M962474-YYY0A M962402-YYY0A LIFT ROD AND KNOB SPOUT KIT 066070-YYY0A AERATOR M907559-YYY0A SPOUT ESCUTCHEON A911914-0070A SEAL Replace the "YYY" with appropriate finish code M961733-0070A SPOUT MTG. KIT CHROME 002 SATIN NICKEL 295 M962248-0070A DECK ADAPTER KIT M962404-YYY0A HANDLE KIT 918555-0070A HANDLE SCREW 918049-0070A ADAPTER M962544-YYY0A 994053-0070A STOPPER CARTRIDGE ASSEMBLY M952430-0070A M906617-0