Resumen del contenido incluido en la página 1
Lighting Systems IS_CD12
9-3/16" (23.34cm)
NOTES:
1. Tools needed: hacksaw, screwdrivers, drill & pliers.
2. Self-driving type “tek” screws may be used in certain
applications to assist in installation and preparation.
3. Be sure to keep fixture runs “As straight as possible”
8-1/4"
for best results.
(20.96cm)
GENERAL DESCRIPTION:
INSTALLATION:
We reserve the right to change details of design, materials and fin
Resumen del contenido incluido en la página 2
Lighting Systems IS_CD12 SELECTION / ORDERING GUIDE Example of Straight Run: 1. at each end trim location for net linear footage. 2. specify voltage 120 or 277. 21' 10-3/4" (667.39cm) O.A.L. 3/4" (1.91cm) 21' 9-1/4" (663.58cm) 3/4" (1.91cm) 45" 90" 90" (114.30cm) (228.60cm) (228.60cm) Telescoping Example of Pattern Run: Unit 1. 2. A. 3. specify voltage 120 or 277. 6' 9" (205.74cm) O.A.L. 3/4" (1.91cm) 5' 8-1/4" (173.33cm) 12" (30.48cm) 12" (30.48cm) 33" (83.82
Resumen del contenido incluido en la página 3
Lighting Systems IS_CD12 SELECTION / ORDERING GUIDE (CONT’D) CD12: One Lamp CD12 CD12-11T CD12-1190 CD12-1145 CD12-1133 CD12-1121 11 11 11 111 11 1 111 11 1 111 11 1 11 1 11 1 11 1 1 11 1 1 1 111 12 1 1111 12 1 12 1 12 1 12 1 1 12 1 1 1 211 13 1 2111 13 1 13 1 13 1 13 1 1 13 1 1 1 311 1 1 3111 1 1 1 1 1 1 1 inch = 2.45 centimeter We reserve the right to change details of design, materials and finish.
Resumen del contenido incluido en la página 4
Lighting Systems IS_CD12 SELECTION / ORDERING GUIDE (CONT’D) CD12: Two Lamps CD12 CD12-12T CD12-1296 CD12-1248 CD12-1236 CD12-1224 11 11 11 111 11 1 111 11 1 111 11 1 11 1 11 1 11 1 1 11 1 1 1 111 12 1 1111 12 1 12 1 12 1 12 1 1 12 1 1 1 211 13 1 2111 13 1 13 1 13 1 13 1 1 13 1 1 1 311 1 1 3111 1 1 1 1 1 1 1 inch = 2.45 centimeter We reserve the right to change details of design, materials and finish.
Resumen del contenido incluido en la página 5
Lighting Systems IS_CD12 PARTS LIST 1. 2. [ ] Service Entry Kits NOTE: END OF RUN PLATES are shipped in the telescopic section cartons. END OF RUN PLATE HOUSING END OF RUN CAPS ELECTRICAL CHASIS END OF RUN PLATE LOUVER RETAINING CLIP SERVICE ENTRY KIT We reserve the right to change details of design, materials and finish.
Resumen del contenido incluido en la página 6
Lighting Systems IS_CD12 INSTALLATION 1. TO INSTALL TROUGH HOUSING 2. TANDEM MOUNTING other, attaching to each other and hanging on NOTE: END OF RUN PLATES are shipped in the telescopic section cartons. HOUSING SUSPENSION END OF RUN PLATE WIRE (by others) SCREW & NUT SCREW & NUT Figure 1 ALIGNER CLIPS Figure 2 3. TRIMMING TELESCOPIC FIXTURES 4. END OF FIXTURE RUN SCREW & NUT SCREW & NUT HOUSING TRIM ALIGNER CLIPS Figure 4 END PLATE Figure 3
Resumen del contenido incluido en la página 7
Lighting Systems IS_CD12 INSTALLATION (CONT’D) 5. INSTALL ELECTRICAL CHASSIS HOUSING END OF RUN PLATE END OF RUN CAPS ELECTRICAL CHASIS END OF RUN PLATE Figure 5 RETAINING CLIP WIRING SCHEMATIC Showing continuous plug & socket connections. (Electrical chassis show separated for simplification) Service entry kit (power feed) CD6B Telescoping unit at end of in line (See page 5) This plug used for corner return connection Start electrical chassis installtion at th
Resumen del contenido incluido en la página 8
Lighting Systems IS_CD12 INSTALLATION (CONT’D) TELE ELECTRICAL (ONE LAMP) TELE ELECTRICAL (TWO LAMP) A. A. section. the channel of the chassis. ELECTRICAL CHASSIS MOUNTING PLATE LAMP ARM WIRES CONDUIT Figure 7 Figure 8 SCREW 6. INSTALL LAMPS (Furnished by others) 7. INSTALL LOUVERS A. INSIDE GROOVE Figure 9 LOUVER ASSEMBLY Figure 10 We reserve the right to change details of design, materials and finish.
Resumen del contenido incluido en la página 9
Lighting Systems IS_CD12 PATTERN RUN WITH CORNERS 1. FIXTURE RUNS USE 90° CORNERS TO CREATE PATTERNS sheet. HOUSING ALIGNER CLIP ELECTRICAL CHASSIS RETAINING CLIP CORNER HOUSING CORNER LOUVER FLEX CONDUIT SECTION Figure 11 CORNER LOUVER 2. TELE PREPARATION Figure 12 We reserve the right to change details of design, materials and finish.
Resumen del contenido incluido en la página 10
Lighting Systems IS_CD12 PATTERN RUN WITH CORNERS (CONT’D) 3. TELE INSTALLATION-INTO CORNER HOUSING CORNER HOUSING Figure 13 4. CORNER-NEXT FIXTURE SUSPENSION WIRE (by others) CORNER HOUSING Figure 14 We reserve the right to change details of design, materials and finish.
Resumen del contenido incluido en la página 11
Lighting Systems IS_CD12 PATTERN RUN WITH CORNERS (CONT’D) ELECTRICAL CHASSIS INSTALLATION HOUSING ELECTRICAL CHASSIS RETAINING CLIP Figure 15 CORNER HOUSING FLEX CONDUIT 5. INSTALL LAMPS (FURNISHED BY OTHERS) 6. LOUVER INSTALLATION HOUSING LOUVER Figure 16 CORNER LOUVER We reserve the right to change details of design, materials and finish.
