Resumen del contenido incluido en la página 1
Henny Penny
Multipurpose Holding Cabinet
Model CF-941
OPERATOR’S MANUAL
REGISTER WARRANTY ONLINE AT WWW.HENNYPENNY.COM
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
Model CF-941 LIMITED WARRANTY FOR HENNY PENNY EQUIPMENT Subject to the following conditions, Henny Penny Corporation makes the following limited warranties to the original purchaser only for Henny Penny appliances and replacement parts: NEW EQUIPMENT: Any part of a new appliance, except baskets, lamps, and fuses, which proves to be defective in material or workmanship within two (2) years from date of original installation, will be repaired or replaced without charge F.O.B. fact
Resumen del contenido incluido en la página 4
Resumen del contenido incluido en la página 5
Model CF-941 TABLE OF CONTENTS Section Page Section 1. INTRODUCTION ............................................................................................... 1-1 1-1. Multipurpose Holding Cabinet ................................................................... 1-1 1-2. Features....................................................................................................... 1-1 1-3. Proper Care ........................................................................................
Resumen del contenido incluido en la página 6
Resumen del contenido incluido en la página 7
Model CF-941 SECTION 1. INTRODUCTION 1-1. MULTIPURPOSE The Henny Penny Multipurpose Holding Cabinet HOLDING CABINET is a basic unit of food equipment designed to hold hot foods at proper temperature in commercial food operations. This cabinet will keep hot foods humid while maintaining temperature. 1-2. FEATURES • Electronic heat and time control for each drawer • Drawer accepts 4" steam table pans (1 full or, 2-1/2 size, or 3-1/3 size) • Easy access to all components for servici
Resumen del contenido incluido en la página 8
Model CF-941 1-5. SAFETY The only way to ensure safe operation of the Henny Penny Multipurpose Holding Cabinet is to fully understand the proper installation, operation and maintenance procedures. The instructions in this manual have been prepared to aid you in learning the proper procedures. Where information is of particular importance or is safety related, the words NOTICE, CAUTION, or WARNING are used. Their usage is described below: SAFETY ALERT SYMBOL is used with DANGER, WARNING, or C
Resumen del contenido incluido en la página 9
Model CF-941 SECTION 2. INSTALLATION 2-1. INTRODUCTION This section provides the installation instructions for the Henny Penny Multipurpose Holding Cabinet. Installation of this unit should be performed by a qualified service technician. Do not puncture the skin of unit with drills or screws as component damage or electrical shock could result. 2-2. UNPACKING The Henny Penny Multipurpose Holding Cabinet has been tested, inspected, and expertly packed to ensure arrival
Resumen del contenido incluido en la página 10
Model CF-941 2-2. UNPACKING (Continued) 5. Pull off any protective covering from the exterior of the cabinet. 6. Your multipurpose holding cabinet is now ready for location and setup. 2-3. ELECTRICAL The multipurpose holding cabinet is available from REQUIREMENTS the factory as a 120 VAC unit. The unit is single phase and requires a grounded receptacle with a separate electrical line protected by a fuse or circuit breaker of the proper rating. To avoid electrical shock, the cabinet mu
Resumen del contenido incluido en la página 11
Model CF-941 SECTION 3. OPERATION 3-1. INTRODUCTION This section provides operating procedures for the multipurpose holding cabinets. Read the Introduction, Installation and Operation Sections and all instructions should be followed before operating the cabinet. This section contains an explanation of all controls, components, and information on operating procedures and daily maintenance. 3-2. OPERATING Figure 3-1 identifies and describes the functions of all th
Resumen del contenido incluido en la página 12
Model CF-941 Figure 3-1 3-3. START-UP Before using the cabinet, it should be thoroughly cleaned as described in the cleaning procedures section of this manual. To put the cabinet into operation, move each POWER switch to the ON position and adjust each control to the appropriate temperature. The power light should illuminate indicating that the unit is operating. The operating temperature of this unit should be achieved in approximately 30 minutes. 3-4. OPERATING WITH 1. Place the hot produ
Resumen del contenido incluido en la página 13
Model CF-941 3-5. CLEANING 1. Move the POWER switch to the OFF position. 2. Disconnect the electrical supply to the unit. To avoid burns, allow the unit to cool before cleaning by opening all the drawers fully for approximately 20 minutes. 3. Remove drawers by pulling straight out and tilting up. 4. Clean drawers with a cloth and soapy water. 5. Remove drip tray from the bottom of the drawer and clean it. 6. Clean the interior of the cabinet thoroughly with a
Resumen del contenido incluido en la página 14
Model CF-941 3-6. OPERATION AND Unit Operation PROGRAMMING Before operating the holding cabinet, read and understand this complete operation manual (supplied with each unit). The following steps are meant to be guidelines, not complete operating instructions. 1. Turn POWER switch to the ON position. 2. The display will show the setpoint temperature. Press the TEMP button at any time to view actual temperature. The LED will light when the actual temperature is on the display. 3. When t
Resumen del contenido incluido en la página 15
Model CF-941 3-6. OPERATION AND Timer Settings PROGRAMMING (Continued) To change a timer setpoint, press and hold the desired timer button, then use the UP and DOWN buttons to change the time. Releasing the timer button enters the time into the controls. If “Loc” shows in the display when the UP or DOWN button is pressed, the controls must be unlocked before temperature can be changed. (See Special Program Mode). When programming the setpoint temperature or timers, pressin
Resumen del contenido incluido en la página 16
Model CF-941 3-6. OPERATION AND 6. Press and release the SET button 4 times and “In-” PROGRAMMING shows in the display. In- means initialization. Press (Continued) and hold the UP or DOWN button at this time and allow the display to count down from 3. The buzzer will sound and the controls will be set at factory settings. 7. Press and release the SET button 5 times and “OP” will show in the display. OP means output test. Press and release the drawer button to turn the r
Resumen del contenido incluido en la página 17
Model CF-941 G L O S S A R Y HENNY PENNY HOLDING CABINETS air temperature probe a round device located inside the cabinet that measures the inside air temperature and sends that information to the control panel concentration ring assembly a metal assembly located in the water pan in the bottom of the unit that helps keep an even humidity level inside the cabinet clean water pan setpoint a preset temperature at which a sensor warns the operator that the water pan has excessive lime deposits con
Resumen del contenido incluido en la página 18
Model CF-941 probe clip a metal holder that attaches to the outside of the control panel to hold the food probe when not in use; the clip is an optional accessory product load capacity the highest recommended number of pounds/kilograms of food product that can be safely held in the cabinet proof function a program used for allowing bread to rise relative humidity the humidity level outside the cabinet setpoint a preset temperature or humidity; the setpoint is a programmable feature system init
Resumen del contenido incluido en la página 19
Henny Penny Corporation P.O.Box 60 Eaton,OH 45320 1-937-456-8400 1-937-456-8402 Fax Toll free in USA 1-800-417-8417 1-800-417-8434 Fax *FM05-016-B* Henny Penny Corp., Eaton, Ohio 45320, Revised 02-14-07 www.hennypenny.com
