Manual de instrucciones de Chief Manufacturing PDC Series

Resumen del contenido incluido en la página 1

INSTALLATION INSTRUCTIONS
Plasma Dual Ceiling Mount
PDC Series

Resumen del contenido incluido en la página 2

PDC Series Installation Instructions DISCLAIMER WARNING: Failure to read, thoroughly understand, and Milestone AV Technologies, Inc., and its affiliated corporations follow all instructions can result in serious personal injury, and subsidiaries (collectively, "Milestone"), intend to make this damage to equipment, or voiding of factory warranty! It is the manual accurate and complete. However, Milestone makes no installer’s responsibility to make sure all components are claim that the informati

Resumen del contenido incluido en la página 3

Installation Instructions PDC Series LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación Perforar Befestigungsteil lösen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging losdraa

Resumen del contenido incluido en la página 4

PDC Series Installation Instructions TOOLS REQUIRED FOR INSTALLATION 9/16" (14.3 mm) PARTS A (1) B (1) C (1) 1/8" 5/32" D (2) D2 (1) D3 (1) 10-24 10-24 x 3/8" D4 (1) 3/16" D6 (1) D5 (1) D1 (1) 4-40 4-40 x 2-1/2" D8 (1) 5/16-18 x 2-3/4" D7 (1) 5/16-18 4

Resumen del contenido incluido en la página 5

Installation Instructions PDC Series 4. Attach interface brackets to back of displays following INSTALLATION instructions included with the interface brackets. Preparing for Installation Installing Displays on PDC 1. Attach click-lock flag kits (D) to PDC following instructions included with the kits. WARNING: EXCEEDING MAXIMUM WEIGHT CAPACITY CAN LEAD TO SERIOUS PERSONAL INJURY OR WARNING: FAILURE TO PROVIDE ADEQUATE DAMAGE TO EQUIPMENT! It is the installers responsibility STRUCTURAL STRENGTH F

Resumen del contenido incluido en la página 6

PDC Series Installation Instructions Remove bolt 2 or padlock 3 if used May remove pin and nut and 1 move to lower holes Pin in "Closed" 2 position - move to "Open" position to remove display A padlock or bolt may be placed through latch holes 5 Figure 4 WARNING: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Ensure mounting buttons are completely engaged in mounting holes. Pin in NOTE: Holes are provided in the faceplate for use with a

Resumen del contenido incluido en la página 7

Installation Instructions PDC Series 4 x 2 1 x 2 5 2 x 2 6 x 2 3 (Display and faceplate removed for clarity) Figure 6 Pitch Adjustment 4. Loosen two screws on side of PDC. (See Figure 6) 5. Adjust to desired pitch, or vertical movement. 6. Tighten the screws on side of PDC. 7

Resumen del contenido incluido en la página 8

PDC Series Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Asia Pacific A Room 24F, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. 8805-000115 Rev.D 2008 Chief Manufacturing P +86-755-8996 9226 www.chiefmfg.com F +86-755-8996 9217 01/08