Manual de instrucciones de Chief Manufacturing KSG110

Resumen del contenido incluido en la página 1

INSTALLATION INSTRUCTIONS
Universal Slat Wall
Dual Arm Mounts
KSG110

Resumen del contenido incluido en la página 2

KSG110 Installation Instructions DISCLAIMER WARNING: Failure to read, thoroughly understand, and CSAV, Inc., and its affiliated corporations and subsidiaries follow all instructions can result in serious personal injury, (collectively, "CSAV"), intend to make this manual accurate and damage to equipment, or voiding of factory warranty! It is the complete. However, CSAV makes no claim that the information installer’s responsibility to make sure all components are contained herein covers all deta

Resumen del contenido incluido en la página 3

Installation Instructions KSG110 LEGEND Pencil Mark Tighten Fastener Marcar con lápiz Apretar elemento de fijación Stiftmarkierung Befestigungsteil festziehen Marcar com lápis Apertar fixador Segno a matita Serrare il fissaggio Potloodmerkteken Bevestiging vastdraaien Marquage au crayon Serrez les fixations Drill Hole Loosen Fastener Perforar Aflojar elemento de fijación Bohrloch Befestigungsteil lösen Fazer furo Desapertar fixador Praticare un foro Allentare il fissaggio Gat boren Bevestiging l

Resumen del contenido incluido en la página 4

KSG110 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 3/16" 5/32" (Provided) (Provided) PARTS A (1) B (1) E (1) C (1) D (1) 3/16" 5/32" G1 G5 G2 G4 F (2) 8-32 x 3/8" G3 G (1) 4

Resumen del contenido incluido en la página 5

Installation Instructions KSG110 INSTALLATION B WARNING: FAILURE TO PROVIDE ADEQUATE STRUCTURAL STRENGTH FOR THIS COMPONENT CAN RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. 1. Install the slat wall bracket (B) following the instructions included with kit.

Resumen del contenido incluido en la página 6

KSG110 Installation Instructions CAUTION: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL Centris Cup INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread engagement in display may cause display to fall! Back out screws ONLY as necessary to allow installation of Centris bracket! 4 1. Ensure Centris cup is able to swivel and tilt easily, yet still G1 x 2 be tight enough to hold display in desired position. Adjust as required before proceeding. See "ADJUSTMENT" for detail

Resumen del contenido incluido en la página 7

Installation Instructions KSG110 Centris Cup G2 or G3 7 (4 places) G4 or G5 Cable Management 5 (4 places) Bracket (in open position) Cable Path (typical) NOTE: Display not shown for clarity. Figure 8 4. Close cable management bracket by sliding it back towards the centerline of the arm (See Figure 7). Figure 6 NOTE: If necessary, cable management bracket attach screws may be tightened using hex key. Cable Management 1. Attach all cables to display. 2. Open the cable management bracket by sliding

Resumen del contenido incluido en la página 8

KSG110 Installation Instructions 2. Using Phillips screwdriver, slightly loosen or tighten the adjustment screw as necessary (See Figure 10). Adjustment Screw 2 Figure 10 3. Reinstall display. See Display Installation in this document. Display Adjustment Lateral position on display: Figure 12 1. Using your fingers, slightly loosen adjustment knob "A". (See Figure 11) 2. Slide display to desired position. 3. Using your fingers, tighten adjustment knob "A". (See Figure 11) PITCH / YAW / ROLL Tensi

Resumen del contenido incluido en la página 9

Installation Instructions KSG110 9

Resumen del contenido incluido en la página 10

KSG110 Installation Instructions USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378 P 800.582.6480 / 952.894.6280 F 877.894.6918 / 952.894.6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands P +31 (0)40 2668620 F +31 (0)40 2668615 Asia Pacific A Room 30I, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112 8832-000237 2007 Chief Manufacturing www.chiefmfg.com P +86-755-8996 9226 ; 8996 9236 ; 8996 9220 08/07 F +86-755-8996 92