Manual de instrucciones de Chauvet 260 LED

Resumen del contenido incluido en la página 1

User Manual

Resumen del contenido incluido en la página 2

Edition Notes The Q-Beam 260-LED User Manual Rev. 01d covers the description, safety Edition Notes precautions, installation, programming, operation, and maintenance of the Q-Beam 260- LED. CHAUVET® released this edition of the Q-Beam 260-LED User Manual Rev. 01d in December 2010. Trademarks CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET® or Chauvet). The CHAUVET® logo in its entirety including the Chauvet name and the dotted triangle, and all other

Resumen del contenido incluido en la página 3

Table of Contents Table of Contents 1. Before You Begin ............................................................................................................1 What is Included ............................................................................................................................. 1 Unpacking Instructions ................................................................................................................... 1 Typographic Conventions ...............

Resumen del contenido incluido en la página 4

Table of Contents Technical Specifications................................................................................................................ 19 -b- Q-Beam 260-LED User Manual Rev. 01d

Resumen del contenido incluido en la página 5

Before You Begin 1. Before You Begin · One Q-Beam 260-LED What is · One IEC power cord with Edison plug (US market) Included · One safety cable · Two omega brackets · Warranty Card · Quick Reference Guide Immediately upon receiving this product, carefully unpack it and check the container in Unpacking which you received it. Make sure that you have received all the parts indicated above and that they are all in good condition. If the material inside the container (this

Resumen del contenido incluido en la página 6

Before You Begin Please read the following notes carefully because they include important safety Safety Notes information about the installation, usage, and maintenance of this product. It is important to read all these notes before starting to work with this product. There are no user serviceable parts inside this product. Any reference to servicing it you may find from now on in this User Manual will only apply to properly CHAUVET® certified technicians. Do not open the hous

Resumen del contenido incluido en la página 7

Introduction 2. Introduction The Q-Beam™ 260-LED is a high power moving yoke fixture equipped with a 60-watt Product white LED. It includes a color wheel with eight slots plus white. It also comes with one gobo wheel with seven rotating slot-n-lock gobos plus open. It also includes a fixed 3- Description facet prism. · 9 or 12-channel DMX-512 LED moving yoke Features · Pan: 540° · Tilt: 270° · Color wheel: 8 colors + white Rainbow color spin at variable speeds ·

Resumen del contenido incluido en la página 8

Introduction DMX Channel Summary DMX Channel Function Basic 1 Pan 2 Tilt 3 Color Wheel 4 Rotating Gobo Wheel 5 Gobo Rotation 6 Fixed Prism 7 Dimmer 8 Strobe 9 Control DMX Channel Function Advanced 1 Pan 2 Pan Fine 3 Tilt 4 Tilt Fine 5 Pan / Tilt Speed 6 Color Wheel 7 Rotating Gobo Wheel 8 Gobo Rotation 9 Fixed Prism 10 Dimmer 11 Strobe 12 Control -4- Q-Beam 260-LED User Manual Rev. 01d

Resumen del contenido incluido en la página 9

Introduction Product Overview Control Panel Fan Power In (IEC) Fuse Holder DMX Out (3-pin XLR) Power Switch Fan DMX In (3-pin XLR) Q-Beam 260-LED User Manual Rev. 01d -5-

Resumen del contenido incluido en la página 10

Introduction Product Dimensions -6- Q-Beam 260-LED User Manual Rev. 01d

Resumen del contenido incluido en la página 11

Setup 3. Setup The Q-Beam 260-LED has an auto-ranging power supply that can work with an input AC Power voltage range of 100~240 VAC, 50/60 Hz. Make sure that you are connecting this product to the proper voltage, as per the specifications in this guide, the product’s user manual, or on the product’s sticker. Always connect the Q-Beam 260-LED to a protected circuit with an appropriate electrical ground to avoid the risk of electrocution or fire. To determine the

Resumen del contenido incluido en la página 12

Setup Make sure to disconnect the fixture’s power cord before replacing the gobo. 1) Loosen the four screws that hold the head’s front cover and move it slightly Gobo forward. Replacement 2) Unfasten the four screws that hold the head’s upper cover and remove it. 3) Manually rotate the gobo wheel and pull out the desired gobo 4) Install the new rotating gobo by sliding it under the pressure plate near the center of the wheel. 5) Reverse steps 1 and 2. You

Resumen del contenido incluido en la página 13

Setup Before mounting this fixture, read and follow the safety recommendations indicated in Mounting the Safety Notes section (page 2 of this manual). Always mount this fixture in any safe position while making sure that there is adequate Orientation room around it for ventilation, configuration, and maintenance. CHAUVET® recommends following the general guidelines below when mounting the Q- Rigging Beam 260-LED. · When selecting an installation location, consi

Resumen del contenido incluido en la página 14

Operation 4. Operation Button Function Control Panel Exits from the current menu or

Description function Enables the currently displayed menu or sets the currently selected value in to the current function Navigates upwards through the menu list and increases the numeric value when in a function Navigates downwards through the menu list and decreases the numeric value when in a function You can set the Q-Beam 260-LED start address i

Resumen del contenido incluido en la página 15

Operation Continued from previous page 1) Go to MENU > INTRO > KEYLOCK. Keylock a) Select YES or NO. When in the “YES” setting, the user will have to enter the password after 30 seconds of control panel inactivity or each time he/she turns the fixture on. The default (non-modifiable) password is, , , and . 1) Go to MENU > INVERT > PAN. Rotation Mode a) Select a movement mode (NORMAL or REVERSE). 2) Go to MENU > INVERT > T

Resumen del contenido incluido en la página 16

Operation Continued from previous page 1) Go to MENU > INTRO > INFO. Software Version a) The display will show the installed software version. 1) Go to MENU > RANGE > P/START. Range Limitation a) Select the starting point for the limited pan (000~255). 2) Go to MENU > RANGE > P/FINISH. b) Select the finishing point for the limited pan (000~255). 3) Go to MENU > RANGE > T/START. c) Select the starting point for the limited tilt (000~255). 4) Go to MENU > RANGE >

Resumen del contenido incluido en la página 17

Operation Menu Map Q-Beam 260-LED User Manual Rev. 01d -13-

Resumen del contenido incluido en la página 18

Operation DMX Values Channel Function Value Percent/Setting BASIC 1 Pan 000 ó 255 0~540º 2 Tilt 000 ó 255 0~270º 000 ó 015 White 016 ó 030 Red 031 ó 045 Yellow 046 ó 060 Magenta 061 ó 075 Green Color Wheel 3 076 ó 090 Orange 091 ó 105 Blue 106 ó 120 Light green 121 ó 135 Light blue 136 ó 255 Rainbow or linear effect 000 ó 010 No gobo 011 ó 020 Gobo 1 021 ó 030 Gobo 2 031 ó 040 Gobo 3 041 ó 050 Gobo 4 051 ó 060 Gobo 5 061 ó 070 Gobo 6 071 ó 080 Gobo 7 Gobo Whe

Resumen del contenido incluido en la página 19

Operation Channel Function Value Percent/Setting ADVANCED 1 Pan 000 ó 255 0~540º 2 Pan Fine 000 ó 255 Fine movement control 3 Tilt 000 ó 255 0~270º 4 Tilt Fine 000 ó 255 Fine movement control 5 Pan/Tilt Speed 000 ó 255 Fast~Slow 000 ó 015 White 016 ó 030 Red 031 ó 045 Yellow 046 ó 060 Magenta 061 ó 075 Green 6 Color Wheel 076 ó 090 Orange 091 ó 105 Blue 106 ó 120 Light green 121 ó 235 Light blue 136 ó 255 Rainbow or linear effect 000 ó 010 No gobo 011 ó 020

Resumen del contenido incluido en la página 20

Technical Information 5. Technical Information To maintain optimum performance and minimize wear, the user should clean the light General fixtures frequently. Usage and environment are contributing factors in determining the cleaning frequency. As a rule, the user should clean the fixtures at least twice a month. Maintenance Dust build up reduces light output performance and can cause overheating. This can lead to reduced light source life and increased mechanical wear. CHAUVE