Resumen del contenido incluido en la página 1
QSDB8209C
Digital LCD Baby Monitor
and Wireless Camera
Visit Us on the Web at http://www.q-see.com
Rev 072208
Resumen del contenido incluido en la página 2
C Cont ontent ents s C Cont ontent ents s 1 Packing List 2 Diagram 3 Structure 4 Installation 5 Specifications 6 FCC and EU 1. Packing List 1) 2.4GHz Wireless Camera ╳ 1 2) 2.4GHz Wireless Receiver ╳ 1 3) Earphone ╳ 1 4) Power Adapter for camera ╳ 1 5) Power Adapter for receiver ╳ 1 Note: AA Batteries are not included
Resumen del contenido incluido en la página 3
2. Diagram 3. Structure 3-1. Layout of Camera
Resumen del contenido incluido en la página 4
3-2. Layout of Receiver 4. Installation 4-1. Setting Up the Camera 1. Setup the camera in the desired location
Resumen del contenido incluido en la página 5
2. Connect the camera to the adapter and then slide the power switch to the ON position Note: --This camera can also use dry batteries as a power source by loading 4 AA batteries into the battery compartment on the back of the camera with their polarities in the correct position. --The AC adapter will work instead of batteries after it is plugged in. If the camera is not going to be used for a long period of time, please unplug the adapter and remove the batteries.
Resumen del contenido incluido en la página 6
4-1-1. Camera Learning Setup If there is interference from another wireless device the Learning Switch can program the unit to avoid it. Push the Learning Switch on the back of the camera from OFF to ON, then press the Eliminate button on the receiver for 3 seconds. The picture will become clearer on the screen. 4-1-2. Camera Alarm Setup 1. The camera provides a Sound Detection alarm.
Resumen del contenido incluido en la página 7
Sound Alarm Setup: To set up the sound alarm slide the alarm switch to the VOX position. The system will enter standby mode until a sound triggers the alarm. When sound is detected the alarm sounds for two minutes or until the Eliminate Alarm button is pressed, which will put the system into snooze mode for 35 seconds. After the 35 seconds is up the alarm will go back into standby mode until triggered by the next sound alarm event. Turn Off Alarm: To turn off the alarm slide the alarm s
Resumen del contenido incluido en la página 8
Note: --This receiver can also use dry batteries as a power source by loading 4 AA batteries into the battery compartment at the back of the camera with their polarities in the correct position. --The AC adapter will work instead of batteries after it is plugged in. If the camera is not going to be used for a long period of time, please unplug the adapter and remove the batteries. * The camera can run off of batteries for up to 5 hours. 2. Adjust the volume control to t
Resumen del contenido incluido en la página 9
3. Set the channel of the receiver to the same channel as the camera by pressing the channel button continuously, the pictures will display on the screen when the channels match. Note: The receiver supports up to 4 cameras working at the same time. If there are 2, 3, or 4 cameras working you can press and hold the channel button about 3 seconds to enter auto-switch-browse mode and the channels will by displayed one by one for 6 seconds at a time.
Resumen del contenido incluido en la página 10
5. Specifications Item Value Transmission Frequency ISM 2,400~2,483 MHz Transmission Power 10mW/CE; 2mW/FCC Operating Frequency 2414MHz;2432MHz;2450MHz;2468MHz Unobstructed Effective 100m (328ft)(Min.) GENERAL Range Spread FHSS/GFSK Spectrum/Modulation Mode Operating Temperature -10 ~ +50(Degree C) / +14~ +122(Degree F) Operating Humidity ≤85%RH Imaging Sensor Type CMOS PAL:720×480 Pixels; Picture Total Pixels NTSC: 720×576 Pixels Horizontal Resolution 380 TV Lines View Ang
Resumen del contenido incluido en la página 11
* Actual transmission range may vary according to weather, Location, interference and building construction. * All the specifications are subject to minor change without prior notice. 6. FCC information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or
Resumen del contenido incluido en la página 12
EU Environmental Protection Electrical waste products (discharged batteries) should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. TRADEMARKS All brand names and products are registered trademarks of their respective Companies. DISCLAIMER The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with re
Resumen del contenido incluido en la página 13
Digital Peripheral Solutions Inc. 8015 E Crystal Drive. Anaheim, CA 92807 1-877-998-3440. Q-See Tech Support in U.S.A. Mon-Fri: 9 am 5 pm PST. TEL:1-877-998-3440 x 539 E-mail: ts@dpsi-usa.com Website: www.q-see.com
