Resumen del contenido incluido en la página 1
2-in-1 Air hAmmer
with 4 pc chisels & needle scAler
model 95801
Assembly And OperA tiOn instructiOns
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
tO preVent seriOus injury, reAd And underst And
All w Arnings And instructiOns befOre use.
© ®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwo
Resumen del contenido incluido en la página 2
specificA tiOns Overall dimensions: 7-1/4” L X 2’ W X 6-1/2” H Activation method: Trigger squeeze design. Net weight: 3.35 lb Air hAmmer: Air inlet: 1/4” - 18 NPT Air Consumption: 4 CFM Maximum Operating Pressure: 90 PSI Types: 1 - Ripping Chisel 1 - Cold Chisel 1 - Punch Chisel 1 - Panel cutter Chisel chisels: Dimensions: Shanks: 0.395” ~ 397” Bore: 0.401” Lengths: 4-3/4” ~ 4-7/8” L Net weights: 3.10 ~ 3.25 oz. Overall dimensions: 9” L X 1-7/8” O.D. Needle qua
Resumen del contenido incluido en la página 3
2. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 3. use protection: Always wear Ansi-approved safety eye goggles, dust mask/ respirator, work gloves, hard toed shoes, long sleeve shirt and long pants when using or servicing this Air hammer. 4. do not operate power tools in explosive atmospheres, such as in the pres- ence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. 5. Keep bystanders, childr
Resumen del contenido incluido en la página 4
16. do not force the tool. use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. Do not force the tool and do not use the tool for a purpose for which it is not intended. 17. do not use the Air hammer if the power switch does not turn it on or off. Any tool that cannot be controlled with the Power Switch is dangerous and must be replaced. 18. disconnect the air supply before making any adjustments, changing acce
Resumen del contenido incluido en la página 5
5. never lay the tool down until it has come to a complete stop. Moving parts can grab the surface and pull the tool out of your control. 6. never leave this Air hammer unattended when it is plugged into an air supply. Turn off the tool, and unplug it from an air supply before leaving. 7. wArning: some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contains chemicals known [to the state of california] to cause cancer, birth defects or other
Resumen del contenido incluido en la página 6
Assembly instructiOns note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 8 of this manual. wArning! Make sure the Power Switch of the tool is in its “OFF” position and that the tool is unplugged from its air supply before making any adjustments to the tool. use As Air hAmmer/chisel 1. Insert the Chisel (17) you wish to use through the Spring (16) and into the front of the Cylinder (13). Twist the Spring (16) onto the t
Resumen del contenido incluido en la página 7
nOte: The threads inside the Cylinder (13) are plastic. Do not exert too much twisting pressure or they can be damaged. The Cylinder should easily twist into the Housing (1) until snug. See figures 2 & 3 3. The Air Hammer is now ready to use as a chisel. 4. To remove, or change chisel heads, simply reverse steps 1 and 2. use As A scAler figure 4 8A 7A 6A 5A 4A 3A
Resumen del contenido incluido en la página 8
figure 4A Hex Wrench for Set Screw (included) 1. Insert the Needles (5A) through the holes in the Needle Holder (4A). There are nineteen Needles. Make sure all holes are filled before putting the Needle Holder (4A) through the Spring (3A), the Retainer Clip (2A) and into the Barrel Assembly (1A). Slide one Retainer Ring (8A) around the Needles (5A) and fasten it at the front end of the Barrel Assembly (1A). See figures 4 & 4A figure 5 Hole for Set Screw 8A 7A 6A 1A
Resumen del contenido incluido en la página 9
OperA tiOn instructiOns 1. With the proper tool attached to the Air Hammer, attach your air supply to the Air Inlet (7) at the base on the Housing (1). Turn on the air supply. Carefully place the tool against the surface of the project you are working with. Make sure the project is in a vise or attached to something that holds it securely so it cannot be moved out of position. 2. Set the Air Regulator (11) located at the base of the Housing (1). Air pressure should not exceed 90 psi. t es
Resumen del contenido incluido en la página 10
problem possible causes probable solutions Air Hammer starts 1. Possible leak in air supply system. 1. Check all hoses, connections on air but not enough air compressor and all lines running pressure. to the Air Hammer. Replace any defective or broken parts. pleAse reAd the fOllO wing cArefully THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESEN- TATION OR WA
Resumen del contenido incluido en la página 11
Assembly diA grAms Air hammer diagram scaler diagram 8A 7A 6A 5A 4A 3A 2A 1A 8A SKU 95801 for technical questions, please call 1-800-444-3353. Page 11
Resumen del contenido incluido en la página 12
wArrAnty LIMIted 1 yeAr w AA rr nty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase. This warranty does not apply to damage due directly or indirectly to misuse, abuse, negligence or accidents; repairs or alterations outside our facilities; or to lack of maintenance.
