Manual de instrucciones de PYLE Audio PYD-1930

Resumen del contenido incluido en la página 1

Specifications
PYD1910/1920/1930/1940/1950
Input Sensitivity/Impedance Equalizer
Control Frequencies 30, 60, 120, 250, 500
Mic 1-2 1.5 mV/600 Ohms, bal/unbal 1K, 2K, 4K, 8K, and 16KHz
Phono 1-2 3.0 mV/50K Ohms
Boost/Cut Range +/- 10 dB from center
Line 1-6 150.0 mV/27K Ohms
MIC Tone Control
Output Level
Treble 10kHz; +10/-30dB
Amp 2.0 V/10-kOhms
Mid 1 kHz; +10/-30dB
Zone 2.0 V/10-kOhms
Bass 100Hz; +10/-30dB
Record 150mV/10-kOhms
Talkover Attenuation -16dB
PYD-1910/PYD1920
Frequency Response 20Hz

Resumen del contenido incluido en la página 2

YourPYLEPROSeriesPerformanceMixer FeaturesandControls:PYD1910Mixer is a sophisticated control center, perfect for mixing sound from multiple playback sources such as microphones, tuners, CD players, turntables or the audio outputs from a VCR. This mixer is ruggedly constructed for home or professional use. Wide range volume controls permit you to adjust sound levels accurately to achieve just the right mix for playing through your speaker system or for recording. MIC 1 Combo Input Jack For Chann

Resumen del contenido incluido en la página 3

FeaturesandControls:PYD1920Mixer FeaturesandControls:PYD1930Mixer ChannelGainControl Lets you adjust the gain of the input source Channel Input Selector Lets you choose the input source to play for each channel Channel CUE Switch Allows you to monitor the selected audio MIC 1 Combo Input Jack For ChannelGainControl Lets you adjust the gain of the input source MIC 1 Combo Input Jack For input source and prepare it prior to mixing it in. connecting a balanced or unbalanced connecting a balanced or

Resumen del contenido incluido en la página 4

FeaturesandControls:PYD1950Mixer FeaturesandControls:PYD1940Mixer ChannelGainControl Lets you adjust the gain of the input source ChannelGainControl Lets you adjust the gain of the input source Channel Input Selector Lets you choose the input source to play for each channel Channel Input Selector Lets you choose the input source to play for each channel Channel CUE/Sample Switch Allows you to monitor the selected audio input source and set up the destination channel for the sampled Channel CUE S

Resumen del contenido incluido en la página 5

PresettingtheControlsBeforeUse Connecting High Level Output Audio Sources Since sudden high output levels from your Pyle Pro mixer can damage not onlyaudio devices connected to the mixer output but your hearing as well (especially if you are using headphones), please adjust Connect up to 8 such sources (tuner, cassette deck, CD Player, camcorder or VCR) to the input jacks the mixer’s controls BEFORE connecting AC power or turning on the unit. for Line 1 (if not being used as Phono 1 input), Line

Resumen del contenido incluido en la página 6

Using the Channel Input Gain Controls UsingHeadphones Adjusting the Gain controls for each channel permits you to fine tune the level of each of the audio inputs, since input levels usually vary. Rotate the Gain controls clockwise to increase levels. After Plug a pair of stereo headphones (not supplied) with a 1/4” jack into the Phones input. Using you preset the gain levels for each input, it is recommended that you do not adjust them further, headphones not only affords you the opportunity to

Resumen del contenido incluido en la página 7

Adding Equalization to the Mix UsingtheMixerControls Turning on the Mixer You can further tailor the sound processed through the mixer to match your acoustic surroundings or suit your personal preferences by using the ten frequency sliders for each channel. To engage the 1. Turn on the output amplifier and temporarily set its volume to the minimum setting. equalization module, press the Equalization On/Off Switch. The LED next to the switch will be illuminated, indicated the EQ mode has been eng

Resumen del contenido incluido en la página 8

UsingtheMono/StereoModeSwitch When the MASTER MONO/STEREO switch is in the MONO position, the mixer combines the right and 4.ToplaybacktherecordedsampleONCE, turn the SAMPLER MODE switch to SINGLE, and press left channels and sends them to the OUTPUT R and L jacks. These combined outputs can be used START/STOP. The LED will go on, indicating that a sample is playing. Pressing START/STOP by a monoaural amplifier, such as a PA amp. during playback will stop the playback. In the STEREO position, ri