Manual de instrucciones de Onkyo PR-SC5507

Resumen del contenido incluido en la página 1

Firmware Update for the TX-NR1007/3007/5007

We are pleased to offer this firmware update for the best possible performance of your AV
Receiver.

The firmware update may fail if an external HDMI control signal is input during the update
procedure. Please be sure to turn off the HDMI control function (RIHD) on your A/V receiver
before starting the update.

How to turn off RIHD:

In the Main menu select "7. Hardware Setup", then "7-4. HDMI".
Set "HDMI Control" to OFF.

· Pleas

Resumen del contenido incluido en la página 2

Firmware Update for the TX-NR1007/3007/5007 A firmware update is now available through the Network connection on the TX-NR1007/3007 and 5007 as well as though the USB connection on the TX-NR3007/5007. The 10/16/09 update addresses: 1. Improved Internet Radio operability 2. Improved picture quality for iPod/iPhone through UP-A1 The 11/19/09 update addresses (TX-NR3007 and 5007 only): 1. Improved display of Chinese menus The 12/22/09 update will: 1. Improves the functi

Resumen del contenido incluido en la página 3

Firmware Update for the TX-NR1007/3007/5007 There are the following methods to update the firmware: via network and via USB storage. Please choose either one that suits your condition. Before you start, carefully read the update procedure. To update the firmware, it will take 15 to 25 minutes for TX-NR1007 and 30 to 40 minutes for TX-NR3007/5007. Update via network You need a wired Internet connection to update the firmware. For the update procedure, please refer to Updati

Resumen del contenido incluido en la página 4

Updating the Firmware via Network TX-NR1007/3007/5007 allow you to update firmware Step 4: using Network connection on rear panel. Select Via NET and push [ENTER]. * In this procedure, on-screen display may vary depending on the model. Note: 1. Make sure your AV receiver/controller and TV are turned on and Ethernet cable is connected to rear panel of the AV receiver/controller. 2. Never unplug or turn off the AV receiver/controller during updating process. 3. To update the firmwa

Resumen del contenido incluido en la página 5

Troubleshooting Case 1: Case 3: If No Update is displayed on the front display of the If you do not have a wired connection to the network, AV receiver/controller as below, the firmware has please contact below. already been updated. You do not need to do anything further. ONKYO CORPORATION 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN The Americas ONKYO U.S.A. CORPORATION Case 2: 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: +1-800-229-1687, +1-201-785-2600

Resumen del contenido incluido en la página 6

Updating the Firmware via USB TX-NR3007/5007 allow you to update firmware using a Step 7: USB storage device. Push [RECEIVER] followed by [SETUP] on the remote * In this procedure, on-screen display may vary depending on the controller. model. Main menu will be displayed on TV screen. Procedures thereafter can also be performed on the Note: AV receiver/controller by using its SETUP, arrow, and 1. Never unplug or turn off the AV receiver/controller ENTER buttons. during updating

Resumen del contenido incluido en la página 7

Updating the Firmware via USB Step 11: Case 2: Select Update and push [ENTER]. If an error occurs, Error!! *-** is displayed on the front display of the AV receiver/controller. (Alphanumeric characters on the front display are denoted by asterisks.) The example below is displaying error code 0-10. See the following table and take appropriate action. Errors during update via USB (excluding TX-NR1007) Error Code Description Updating will begin. *-10, *-20 USB storage devi