Resumen del contenido incluido en la página 1
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
Contents Newton Series HD Introduction ................................................................... 4 High Performance Product Contents .......................................................... 4 Inspecting for Damage .................................................. 4 Loudspeaker System Configuration .................................................... 5 Speaker Placement ....................................................... 5 Wiring ................................................
Resumen del contenido incluido en la página 4
Introduction Thank you for choosing a Newton HD Series speaker. The MC630HD features the finest drivers, precision internal crossover circuitry, and an elegant enclosure design. The design team at Cambridge SoundWorks believes there is no better combination of audiophile-level attention to detail and reasonable cost. Contents 1. One Speaker 2. Two stick-on rubber feet 3. Four clear round stick-on rubber feet 4. Center Channel rear support 5. ¼-20 machine screw for rear support 6. Two s
Resumen del contenido incluido en la página 5
140º 110º 30º System Configuration For the most balanced performance use an MC630HD on all channels of the surround-sound system. They are also excellent to use as rear or surround speakers in a system using MC650HD front speakers. If you prefer smaller or in-wall surround and rear speakers, any of the Cambridge SoundWorks Newton Series speakers may be substituted with good results. The Left, Center, and Right speakers should all be the same for the most accurate sound stage. The MC630HD
Resumen del contenido incluido en la página 6
Wiring The Speakers If you wish to conceal the wire within the walls, it is easiest to run the wires to their final positions prior to mounting the speakers. The spring loaded terminals of the MC630HD accept bare wire between AWG #12 and AWG #18 (lower numbers are thicker). It is not necessary to “tin” the wire or use connectors to terminate the wire. • Use at least AWG #18 speaker cable for short runs (under 15 feet). Use AWG #16 or heavier speaker cable for longer runs. • Building cod
Resumen del contenido incluido en la página 7
Speaker Mounting The MC630HD may be wall mounted or placed horizontally on a table-top as a center-channel using the included hardware. Matching floor and table-top stands are available separately from Cambridge SoundWorks. Hanging The Speaker On The Wall The MC630HD may be mounted either vertically or horizontally using the supplied wall anchors. 1. Using the dimension diagram as a guide, mark the position of two locations for mounting screws and anchors. The anchors will not be nee
Resumen del contenido incluido en la página 8
Placing Horizontally On a Tabletop Or Shelf 1. Attach the rear support into the channel on the rear of the speaker using the included ¼-20 machine screw. Tighten the set-screw finger-tight to stabilize the support. 2. Attach two rubber hook-shaped stick-on feet symmetrically along the bottom edge of the speaker approximately 10” apart. If you are mounting the speaker on an uneven surface you may need to attach the feet closer to the center. Adapt the actual position to your needs. 3. Remov
Resumen del contenido incluido en la página 9
Setting Bass Contour The switch located near the connection terminals optimizes the low frequency response of the speaker for wall or stand mounting. • When the speaker is mounted on a speaker stand, away from the wall press the end of the switch marked with “|”. • When the speaker is mounted on the wall or table, press the end of the switch marked with “o”. The upper bass range will be slightly attenuated to compensate for the increase in bass caused by wall reflection. The above re
Resumen del contenido incluido en la página 10
Specifications Dimensions: 17 5/16” H x 6 1/2” W x 3 7/8” D Weight: 14 pounds each Impedance: nominal 8 ohms Recommended amplifier power range: 20W – 100W RMS per channel Frequency Range: 80Hz – 24kHz Woofer Type: 2 x 4” with co-injection molded composite cones and butyl-rubber surrounds Tweeter Type: ¾” aluminum dome with ferrofluid-damping and neodymium magnet Crossover: 2 way, series-connected Enclosure: High-density pressure-cast aluminum with molded-co
Resumen del contenido incluido en la página 11
Resumen del contenido incluido en la página 12
120 Water Street North Andover, MA 01845 (800) FOR-HIFI (1-800-367-4434) www.cambridgesoundworks.com email: info@cambridgesoundworks.com P81-2460
