Resumen del contenido incluido en la página 1
Integrated IR Bullet Camera
WZ16
en Installation Manual
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
WZ16 Integrated IR Bullet Camera Table of Contents | en 3 Table of Contents 1 Safety 4 1.1 Safety Precautions 4 1.2 Important Safety Instructions 4 1.3 Important Notices 5 1.4 FCC & ICES compliance 7 1.5 CSA certification 8 1.6 Warranty / Limitation of Liability 8 2 Introduction 10 2.1 Parts Included 10 3 Installation and Connection 11 4 Configuration 13 4.1 Adjusting the Zoom 13 4.2 Adjusting the Focus 13 4.3 Adjusting the Video Output Brightness 13 5 Troubleshooting 14 5.1 5.1 Troubl
Resumen del contenido incluido en la página 4
4 en | Safety WZ16 Integrated IR Bullet Camera 1 Safety 1.1 Safety Precautions DANGER! High risk: This symbol indicates an imminentlyhazardous situation such as “Dangerous Voltage” inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death. WARNING! Medium risk: Indicates a potentially hazardous situation. If not avoided, this could result in minor or moderate bodily injury. CAUTION! Low risk: Indicates a potentially hazardous situation. I
Resumen del contenido incluido en la página 5
WZ16 Integrated IR Bullet Camera Safety | en 5 18. These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualified to do so. 1.3 Important Notices Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit may fall, causing serious injury and/or serious damage to the unit. Use on
Resumen del contenido incluido en la página 6
6 en | Safety WZ16 Integrated IR Bullet Camera Electrostatic-sensitive device - Use proper CMOS/MOS-FET handling precautions to avoid electrostatic discharge. NOTE: Wear required grounded wrist straps and observe proper ESD safety precautions when handling the electrostatic-sensitive printed circuit boards. Moving - Disconnect the power before moving the unit. Move the unit with care. Excessive force or shock may damage the unit and the hard disk drives. Outdoor signals - The installati
Resumen del contenido incluido en la página 7
WZ16 Integrated IR Bullet Camera Safety | en 7 1.4 FCC & ICES compliance FCC Information (U.S.A. and Canadian Models Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordan
Resumen del contenido incluido en la página 8
8 en | Safety WZ16 Integrated IR Bullet Camera Toute modification apportée au produit, non expressément approuvée par la partie responsable de l’appareil, est strictement interdite. Une telle modification est susceptible d’entraîner la révocation du droit d’utilisation de l’appareil. La brochure suivante, publiée par la Commission fédérale des communications (FCC), peut s’avérer utile : How to Identify and Resolve Radio-TV Interference Problems (Comment identifier et résoudre les problè
Resumen del contenido incluido en la página 9
WZ16 Integrated IR Bullet Camera Safety | en 9 The liability of BOSCH Security Systems hereunder or otherwise is solely and exclusively limited to replacement (new or refurbished Product), repair, or credit of the amortized purchase price, as BOSCH Security Systems may elect, for any Product which is returned by Buyer during the applicable warranty period, or services for which timely notice of defect has been given by Buyer, and which are found by BOSCH Security Systems to be subject
Resumen del contenido incluido en la página 10
10 en | Introduction WZ16 Integrated IR Bullet Camera 2 Introduction The WZ16 Integrated IR Bullet Camera is a night vision DSP Color CCD camera that uses a 1/3” CCD solid-state imaging device that provides superior performance. The camera can be installed easily in most indoor and outdoor locations. Features include: – Day/night operation – Infrared, photocell-controlled LEDs – Weight of less than 1.5 pounds / 0.6 kg – IP67 rating – Operates at temperature range from -30 °C to +55 °C (
Resumen del contenido incluido en la página 11
WZ16 Integrated IR Bullet Camera Installation and Connection | en 11 3 Installation and Connection DANGER! RISK OF ELECTRIC SHOCK! DO NOT OPEN THE UNIT! WARNING! To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the following installation instructions. CAUTION! Do not install the camera near electric or magnetic fields. If possible, do not install in a kitchen or boiler room as heat will affect the camera. CAUTION! Do not use a power source o
Resumen del contenido incluido en la página 12
12 en | Installation and Connection WZ16 Integrated IR Bullet Camera Figure 3.2 Camera mounted (from bottom) on Wall Figure 3.3 Camera mounted (from top) on Wall 4. Connect the camera to the video monitor. Bosch recommends using a monitor with a CCTV quality 75Ω video impedance level. If your monitor is switched to high impedance, please adjust the monitor accordingly. Figure 3.4 Standard 12 VDC BNC(RCA) Connection Number Description 1 12 VDC or 24 VAC regulated power supply 2 Vid
Resumen del contenido incluido en la página 13
WZ16 Integrated IR Bullet Camera Configuration | en 13 4 Configuration Follow the steps below to adjust the zoom and focus. Remove the lens cap before making adjustments, then replace it when you finish. Refer to the figure below. Figure 4.1 Lens adjustment Number Description 1 Zoom control 2 Focus control 3 Video brightness CAUTION! To prevent humidity problems, the camera must be installed in dry conditions. Removing the lens cap in a wet or humid environment may result in condensation
Resumen del contenido incluido en la página 14
14 en | Troubleshooting WZ16 Integrated IR Bullet Camera 5 Troubleshooting 5.1 Troubleshooting Tips Before sending the camera out for repair, check the items below. If the problem persists after checking these items, contact your service center. - If no image appears, verify that: – The coaxial cable is attached securely. – The power and voltage are normal. – There is adequate illumination. - If the image is unclear, verify that: – The lens is in focus. – The lens is not dirty. Dirt or fi
Resumen del contenido incluido en la página 15
WZ16 Integrated IR Bullet Camera Technical Specifications | en 15 6 Technical Specifications Electrical Power 12 VDC (±10%) Max 700 mA 24 VAC (±10%) Max 7 W Surge Suppression Peak current: 2000 A (8/20 μs) Peak power: 5500 W (2 ms) Power Input Videos Signal Format NTSC PAL NTSC PAL Image Device 1/3 in. Super HAD CCD 1/3 in. Super HAD CCD II Scanning Systems 2 : 1 Interlace Horizontal 540 TVL Resolution Total Pixels 811 x 508 795 x 596 811 x 508 795 x 596 Effective Pixels 768 x 494 752 x 58
Resumen del contenido incluido en la página 16
16 en | Technical Specifications WZ16 Integrated IR Bullet Camera Dimensions Below are several dimensional drawings of the camera. Unit of measure is mm. Figure 6.1 Front view Number Description 1 Photocell 18 LED Figure 6.2 Bottom view Figure 6.3 Side view | 1.0 | 2010.12 Installation Manual Bosch Security Systems, Inc.
Resumen del contenido incluido en la página 17
WZ16 Integrated IR Bullet Camera Technical Specifications | en 17 Figure 6.4 Mounting bracket Bosch Security Systems, Inc. Installation Manual | 1.0 | 2010.12
Resumen del contenido incluido en la página 18
Resumen del contenido incluido en la página 19
Resumen del contenido incluido en la página 20
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA 17601 U.S.A. www.boschsecurity.com © Bosch Security Systems, Inc., 2011
