Resumen del contenido incluido en la página 1
Model: APS-610a
Owner’s Manual
4 Button Remote Security System
with Dual Stage Shock Sensor
IMPORTANT ! In order to provide the highest possible level of security to your vehicle, this
system is equipped with selectable manual override circuitry. It is possible that you will need
to manually override your security system if the transmitter becomes lost, or inoperative due to
battery failure. Reading the sections on "MANUALLY OVERRIDING YOUR SYSTEM" is nec-
essary to fully understand the proced
Resumen del contenido incluido en la página 2
YOUR "Code Hopping" TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system. Some of today’s sophisticated auto thieves use a device known as a code grabber, which will receive and store the signal from your keychain transmitter, and re transmit at a later time to disarm your system. Your code hopping transmitters will change their signal every time the button is
Resumen del contenido incluido en la página 3
ARMING THE SYSTEM - PASSIVE ( AUTOMATIC ) 1. Turn off the engine, exit the vehicle, close and lock all doors, hood lid and trunk lid. Red dash mounted LED begins to flash rapidly, indicating 30 second passive arming has begun. 2. Opening any protected entry point during the 30 second passive arming cycle will imme- diately suspend automatic arming, and the 30 second passive arming cycle will restart when all doors are closed. At the end of the passive arming cycle; Red dash mounted LED begin
Resumen del contenido incluido en la página 4
Parking Lights flash two times. If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, examine the LED to identify which zone was triggered. Siren sounds two chirps. If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before turning the key on, examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was trig- gered. If the siren did not sound when disarming, t
Resumen del contenido incluido en la página 5
action will turn off the siren yet leave the vehicle fully armed and protected. This feature is particularly useful if you are aware of children playing near your vehicle that may accidently trigger your security system. In this case you can cancel the siren sounding without disarming your alarm. INTRUSION WARNING SIGNALS This system will inform you if an intrusion attempt has occurred while you were away from the vehicle. If an intrusion attempt has occurred, the siren will chirp 4 times and t
Resumen del contenido incluido en la página 6
Typically this override mode is used only if the transmitter has become inoperative. You may elect to enter the VALET mode until repair or replacement of the transmitter, after which, returning the system to the full operation mode is necessary. To do so, see item 3 under the heading VALET SWITCH. Programming Your Custom Override Code: Unlike override switches easily found and defeated, this security system allows the con- sumer to program a personal override code, offering a higher level of se
Resumen del contenido incluido en la página 7
6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch off then on. 7. Within 10 seconds, begin to press and release the push button switch to set the units digit. (As per the example, press and release 2 times to set the units digit to 2). 8. Turn the ignition switch to the off position. Immediately observe the LED flash pattern. You will note the LED flashing five times, pause, and then flash two times, pause. This pattern will be repeated three times indicating t
Resumen del contenido incluido en la página 8
defective zone indicator will always operate. Since these are important warnings to you that something has happened, they cannot be eliminated. REMOTE PANIC OPERATION The ARM or DISARM button on your keychain transmitter also functions as a panic switch for use in emergency situations. To use remote panic, 1. Press and hold the ARM or DISARM button on the keychain transmitter for 3 or more seconds. The alarm will immediately sound. 2. To stop the alarm, press and hold the ARM or DISARM button on
Resumen del contenido incluido en la página 9
ADDITIONAL REMOTE FUNCTION ( CHANNEL 5 ) This security system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are; Remote Trunk Release Remote Car Starter Remote Window Closure Remote Garage Door Interface To activate the optional accessory, press the programmed button on the keychain transmit- ter for up to 8 seconds for continuous output, or press and release for momentary activa- tion. The op
Resumen del contenido incluido en la página 10
APS 610a SYSTEM FUNCTIONS AT A GLANCE DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 SIREN CHIRP INDICATORS *1 CHIRP = ARM *2 CHIRPS = DISARM 3 CHIRPS = ARM / DOOR OPENED 4 CHIRPS = DISARM / INTRUSION * These chirps are optional, and can be de-activated. PARKING LAMP INDICATORS 1 FLASH = ARM 2 FLASHES = DISARM 3 FLASHES = DISAR
