Manual de instrucciones de Pelco PAXM100

Resumen del contenido incluido en la página 1

INSTALLATION
™
ExSite Series Mounts
WXM100, CMXM100,
PAXM100, and PXM100
WXM100
C2216M (5/05)

Resumen del contenido incluido en la página 2

Resumen del contenido incluido en la página 3

Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Only use attachments/accessories specified by the manufacturer. 6. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 7. Installation should be done only by qualified personnel and

Resumen del contenido incluido en la página 4

Description ™ This manual contains the installation instructions for the following ExSite Series mounts: WXM100 Wall mount designed to mount the ExSite Series system directly to a load-bearing vertical surface. CMXM100 Corner adapter for use with the WXM100 to mount an ExSite Series system to the corner of a structure. PAXM100 Pole adapter for use with the WXM100 to mount a system to a horizontal pole. PXM100 Pedestal mount designed to mount an ExSite Series system directly to a hori

Resumen del contenido incluido en la página 5

Installation WXM100 WALL MOUNT To install the WXM100 refer to Figure 1 and perform the following steps: 1. Determine the mounting location. The mounting surface should be able to support four times the combined weight of the mount and ExSite system. 2. Using the flanged end of the wall mount as a template, mark the five fastener hole positions onto the mounting surface. Set the WXM100 mount to the side and prepare the holes for the fasteners. 3. Position the wall mount over the mounting

Resumen del contenido incluido en la página 6

CMXM100 CORNER MOUNT ADAPTER To install the CMXM100 refer to Figure 2 and perform the following steps: 1. Attach the corner mount adapter to the mounting surface with the appropriate hardware (not supplied). The mounting surface should be able to support four times the combined weight of the corner mount adapter, WXM100 mount, and ExSite system. 2. Attach the WXM100 wall mount to the corner mount adapter with the supplied five 3/8-16 x 1.0-inch thread length, stainless steel hex head bol

Resumen del contenido incluido en la página 7

PAXM100 POLE MOUNT ADAPTER Install the PAXM100 to a steel pole with a diameter between 4 and 9 inches (10.16 to 22.86 cm). Refer to Figure 3 and perform the following steps: 1. Attach the pole mount adapter to the pole with the four stainless steel straps (supplied). Tighten the clamps of the straps to 6.25 to 7.5 ft-lb (8.5 to 10.2 Nm). 2. Attach the WXM100 wall mount to the pole mount adapter with the supplied five 3/8-16 x 1.0-inch thread length, stainless steel hex head bo

Resumen del contenido incluido en la página 8

PXM100 PEDESTAL MOUNT The PXM100 mount is designed to make the installation and removal of the ExSite power module quick and easy. To install the PXM100 refer to Figure 4 and perform the following steps: 1. Attach the power module of the ExSite system to the pedestal mount with four M10 x 16 mm stainless steel bolts and lock washers supplied with the power module (refer to Figure 4). Tighten the bolts to 25 to 27 ft-lb (34 to 37 Nm). NOTE: Figure 4 shows the power module being instal

Resumen del contenido incluido en la página 9

Specifications Construction Mounts Electro-polished 304 stainless steel PAXM100 Mounting Straps 316 stainless steel CMXM100 Maximum Load WXM100 73 lb (33 kg) CMXM100 85 lb (38.50 kg) PAXM100 88 lb (40 kg) 8.15 (20.7) PXM100 79 lb (35.83 kg) Weight WXM100 12.4 lb (5.62 kg) CMXM100 7.6 lb (3.45 kg) PAXM100 9.2 lb (4.17 kg) 9.25 (23.5) PXM100 1.3 lb (0.60 kg) 14.9 (37.8) 5.5 (14.1) WXM100 8X Ø 0.433 THRU EQ SP 5X Ø THREADED HOLES ON A 4.75 B.C. FOR 3/8-16 SS BOLTS 8.00 (20.32) PXM100 4X Ø 0.413

Resumen del contenido incluido en la página 10

10 C2216M (5/05)

Resumen del contenido incluido en la página 11

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or workmanship for a period of one year after the date of shipment. (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information: Exceptions to this warranty are as noted below: 1. Model and serial number

Resumen del contenido incluido en la página 12

Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO9001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East | | | | | | | |