Manual de instrucciones de Pelco MPS524DT/220

Resumen del contenido incluido en la página 1

®
MPS5DT, MPS524DT,
MPS524DT/220
Scanner Controls
Installation/
Operation Manual
C545M-E (2/02)
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • Pelco Online @ www.pelco.com
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150 • DataFAX (800) 289-9108
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120 • DataFAX +1(559) 292-0435
PelcoEurope BV • Dillenburg Center, Dillenburgstraat 7C • 5652 AM Eindhoven • The Netherlands
Tel +31(40) 251-9870 • FAX +31(40) 25

Resumen del contenido incluido en la página 2

CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ................................................................3 DESCRIPTION ..................................................................................................................4 MODELS ....................................................................................................................4 OPTIONS ...................................................................................................................4

Resumen del contenido incluido en la página 3

IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed: 1. Installation and servicing should only be done by Qualified Service Personnel and conform to all Local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6 or 6P enclo- sure, it is designed for indoor use only and it must not be installed where exposed to rain or moisture. 3. Only use replacement parts recommended by Pelco. 4. After replace

Resumen del contenido incluido en la página 4

DESCRIPTION The MPS5DT and MPS524DT Scanner Controls provide precise and reliable control of Pelco PS20 and PS20-24 Series Scanners. The controls can still be used with older scan- ner models such as Pelco PS7, PS7-24, PS30A, and PS30-24. An additional line is available to power the PS20 scanner and camera/enclosure eliminating the need for power at the scanner location. The front panel switches operate left and right control, and automatic scan control. These controls can be used as desktop mo

Resumen del contenido incluido en la página 5

INSTALLATION The following items are supplied: • MPS5DT, MPS524DT, or MPS524DT/220 •6-pin mating connector with pins •2 screws CONNECTOR ASSEMBLY The first thing you must do is assemble the mating connector. The following steps apply to all AMP style connectors regardless of pin size or pin number. Refer to Figure 1 during as- sembly. 1. Slide the connector clamp assembly over the conductor cable. 2. Determine the size of wire to use. Refer to the Specifications section. 3. Prepare the wires fro

Resumen del contenido incluido en la página 6

COMPLETING THE INSTALLATION 1. Attach the mating connector to the connector on the rear of the scanner control. 2. Attach the other end of the cable to the scanner. 3. Plug the power cord on the back of the scanner control into a 120 VAC outlet (MPS5DT and MPS524DT models) or a 230 VAC outlet (MPS524DT/220 model). OPERATION Turn the control on and test its operation using the following procedures: MANUAL OPERATION Move the rocker switch to the “MANUAL” position. When you move the other rocker sw

Resumen del contenido incluido en la página 7

Power Cord: Unit is supplied with grounded power cord (either U. S. Standard or Continental European Standard) Output Connector: AMP CPC type, 14 pin (mate supplied) Cable Requirements: 4 conductors for PS7/PS30 models and 6 for PS20/PS20-24 models Operating Distances: The following are the recommended cable distances between the control and the listed scanners. The PS20 and PS20-24 are pow- ered locally and do not use power from the controller. 20 AWG 18 AWG 16 AWG 2 2 2 (0.5 mm ) (1.0 mm ) (1.

Resumen del contenido incluido en la página 8

REGULATORY NOTICES This equipment has been tested and found to comply with the limits of a Class A digital de- vice, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful in- terference to radio communicat