Manual de instrucciones de Oki OK-NIP10-A420GP

Resumen del contenido incluido en la página 1

OK-NIP10-A420
OK-NIP10-A420P
OK-NIP10-A420G – Wireless
OK-NIP10-A420GP – Wireless
PTZ X10 MPEG4/JPEG IP Camera
Quick Installation Guide
This guide describes the basic functions of
Network Camera with Pan/Tilt/Zoom.
All detailed information is described in the user’s manual.
0

Resumen del contenido incluido en la página 2

Warning Before Install Power off the Network Camera as soon as it is found smoking or smelt unusual. Contact your distributor when such cases happen. Keep the Network Camera away from the water. If the Network Camera is wet, power off immediately. Contact your distributor when such cases happen. Do not place the Network Camera around the heat sources, such as television or oven. Refer to your user’s manual for the operating temperature. Keep the Network Camera away from the direct sunl

Resumen del contenido incluido en la página 3

Do not touch the Network Camera when it’s lightening. Do not disassemble the Network Camera. Do not drop the Network Camera. Do not manually pan and tilt the Network Camera when are power is on. Do not insert any object into the Network Camera, such as needles. 2

Resumen del contenido incluido en la página 4

1. Check Package contents The Network Camera (Wire or Wireless model) Power adapter Camera stand A/V cable Antennas for wireless model only Software CD Remote controller 3

Resumen del contenido incluido en la página 5

2. Physical description Front panel Antennas for wireless model only Lens Microphone Status LEDs Rear panel A/V out EXT I/O External Mic.. Note the serial number from the label on the unit. Ethernet 10/100 RJ45 socket This serial number is the same as the Ethernet address. Power cord socket for example:0002D1455282 =00-02-D1-45-52-82 4

Resumen del contenido incluido en la página 6

3. Install your Network Camera in Ethernet network Antennas for wireless model only 1. If you have external devices such as sensors and alarms, make connection form I/O terminal block. *Refer to your user’s manual for the I/O 2. Use Ethernet cable to make connection from Ethernet port to the hub. *Use Category 5 Cross Cable when the Network Camera is directly connected to a PC. 3. Finally, connect power cord to a power outlet. 5

Resumen del contenido incluido en la página 7

4. Assign IP address 1. Run the “Installer Wizard” under the Software Utility directory from software CD. 2. The program will search the servers or cameras on the same LAN. 3. After searching, the main installer window will pop up. Click on serial number that matches the one you just note from 2. Physical description 4. Click “Link to selected device(s)” to connect the Internet Explorer to the Network Camera. If there is no DHCP server on the LAN, please refer to the user’s ma

Resumen del contenido incluido en la página 8

5. The Internet Explorer Connects to the Network Camera For setup further configuration, please check user’s manual on the software CD. 7

Resumen del contenido incluido en la página 9

6. Client Settings (Windows XP/2000/Me/98SE) At the initial access to the “Connection type” page in Windows, the web browser will ask for a new plug-in installation, the plug-in being the Network Camera. This plug-in has been registered for certification and can be used to change the parameters at the client’s site. The user may click on to install the plug-in. If the web browser does not allow the user to complete the installation, check the Internet security to lower the security level or

Resumen del contenido incluido en la página 10

3. Lower down the security level bar to “Low”, and press “Apply” 4. Refresh IE Browser, a question frame will pop-up to ask for download Active-X. press “Yes”. 9

Resumen del contenido incluido en la página 11

7. Client Settings (Windows XP SP2) 1. Initial IE browser, select function item “Tools” “Internet Options” 2. Security ”Custom Level” 10

Resumen del contenido incluido en la página 12

3. Security Settings Download unsigned ActiveX Controls set “Enable” and press “OK” 4. Press “Apply” and then “OK” 11

Resumen del contenido incluido en la página 13

5. Key-In camera’s IP address and press “OK” on Information Bar. 6. Click the blue bar under the Camera’s IP address in the browser, then choose “Install ActiveX Control” 7. Recover security settings. Download unsigned ActiveX Controls set “Disable” and press “OK” and “Apply” 12