Resumen del contenido incluido en la página 1
®
Installation/Operation
®
150 Series Camclosure
Integrated Camera System
C2410M-G (1/04)
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • Pelco Online @ www.pelco.com
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150 • DataFAX (800) 289-9108
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120 • DataFAX +1(559) 292-0435
Resumen del contenido incluido en la página 2
[ 2 ] Pelco Manual C2410M-G (1/04)
Resumen del contenido incluido en la página 3
CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS ..................................................................................... 4 DESCRIPTION ........................................................................................................................................ 4 INSTALLATION ........................................................................................................................................ 4 INSTALL BACK BOX ....................................
Resumen del contenido incluido en la página 4
IMPORTANT SAFEGUARDS AND WARNINGS 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6 or 6P enclosure, it is designed for indoor use only and must not be installed where exposed to rain and moisture. 3. Use only installation methods and materials capable of supporting four times the maximum specified load. 4. Use stainless steel hardware to fasten the enclosur
Resumen del contenido incluido en la página 5
Mounting to 4S Deep Electrical Box 1. Attach adapter plate to the 4S box with the two 8-32 x .750-inch screws. 2. Connect the video cable. 4S DEEP ELECTRICAL BOX 3. Connect the power wires. • For 12 VDC, connect the WALL OR 24 VAC/12 VDC (red) and GND CEILING 8.32 X .750 SCREW (black) wires to input power. (SUPPLIED) ADAPTER PLATE • For 24 VAC, connect the 24 VAC/12 VDC (red) and BACK BOX 24 VAC (blue) wires to input 01063 8.32 X .375 SCREW (SUPPLIED) power. 4. Attach the back box to the adapter
Resumen del contenido incluido en la página 6
VIDEO 2. 12 VDC Operation Only - The camera CONNECTOR is set for 24 VAC operation at the HEATER factory. For 12 VDC operation CONNECTOR remove the jumper from the 24 VAC position 24 VAC JUMPER and install it on the 12 VDC JUMPER 12 VDC position. 01065 3. If the heater is installed, plug the heater connector from the camera into the mating connector inside the base. Plug the video connector from the camera into the mating connector inside the base. Turn on power to the camera and monitor. VIDEO C
Resumen del contenido incluido en la página 7
3 Install Dome and Trim Ring Place the trim ring and dome over the back box. If the dome has a liner, position the viewing window over the lens of the camera. Tighten the tamper-resistant screws with the supplied 1/8-inch hollow screwdriver bit. Note 01074 that the screws are installed at an angle. ADJUSTMENTS (COLOR CAMERA ONLY) If you have a color camera, it is set up at the factory and normally requires no adjustments. Sometimes, however, adjustments may be necessary. 1. Remove the dome and
Resumen del contenido incluido en la página 8
Auto Iris Level Adjustment If you have a varifocal lens or fixed focal length lens with an auto iris, you can adjust the level setting to increase or decrease brightness. Focus Adjustment for Fixed Focal Length Lens with Auto Iris CAUTION Heater elements could be hot! When camera power is on, use caution when adjusting the camera. To adjust the focus, it may be necessary to remove the heater board in order to loosen the locking screw on the bottom of the lens. HEATER To remove the heater board:
Resumen del contenido incluido en la página 9
Switch Settings for Fixed Focal Length Lens with Auto Iris Refer to the switch drawing. The switch is located next to the lens. Automatic backlight compensation (factory setting) is used under varying lighting conditions (such as outdoors) or fixed lighting conditions where there are no bright spots that darken other picture details. Manual backlight compensation is used in fixed lighting conditions to optimize the picture detail when there are bright spots. ALC/ELC switch: Always ALC FACTORY SE
Resumen del contenido incluido en la página 10
Switch Settings for Varifocal Lens The high resolution camera with 1AWB Automatic white balance varifocal lens and auto iris is FACTORY SETTINGS 2 GAM Gamma function configured at the factory for 3 AGC Automatic gain control 12345678 optimal performance in lighting 4 ESC Electronic shutter control conditions where auto iris is 5 BLC Backlight compensation required. It is also configured with 6FL Flickerless OFF the shutter speed set at 1/60 7AE Automatic exposure = SWITCH POSITION (NTSC) or 1/50
Resumen del contenido incluido en la página 11
Regulatory Notices FCC Class A (monochrome, EIA and CCIR cameras – except auto iris models) This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the i
Resumen del contenido incluido en la página 12
WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC3600 Series); two years on all other cameras. ® ® • Three years on Genex Series (multiplexers, server, and keyboard) and 090 Series Camclosure Camera System. ® • Two years on
