Resumen del contenido incluido en la página 1
WIRELESS HOME
SECURITY SYSTEM
Instruction Manual
English Version1.0
MODEL:
WA-410
www.lorexcctv.com
Copyright © 2007 Lorex Technology Inc.
Resumen del contenido incluido en la página 2
Table of Contents Introduction…………………………………………………………………………….…... 3 System Package…………………………………………………………….…. 3 Optional Accessories…………………………………………………………... 3 Planning for Installation Choosing a Location………………………………………………………..…... 4 Setting Alarm Zones…………………………………………………………..... 4 4 Installing the Back-up Battery………………………………………………..... 4 Powering the
Resumen del contenido incluido en la página 3
Important Safety Instructions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE OR POWER ADAPTER TO WATER OR MOISTURE • Read Instructions – All the safety and operating instructions should be read before operating this equipment. These instructions should be retained for future reference • Heed Warnings – All warnings on the equipment and in the operating instructions should be adhered to. All instructions regarding care and operation of this eq
Resumen del contenido incluido en la página 4
Introduction Thank you for choosing the Lorex® WA410 Wireless Home Security System. These security systems are high-quality, reliable and versatile. This system has a built in Auto- dialer for increased security. To ensure the best performance of your system, please read this manual thoroughly and follow the precautions and instructions presented. These systems are designed to be simple and easy to install and maintain. Wireless easy to use : No messy and expensive wiring is req
Resumen del contenido incluido en la página 5
Planning for Installation The security system is designed to be as flexible as possible in order to meet your present needs, and also to adapt as your needs change. For the reason, we recommend that you read and consider the following information and plan your system before installing these devices. Choosing Location It is important to try and place the Main Console in an area central to the alarm sensors. This way, all of the sensors can transmit signals with maximum ef
Resumen del contenido incluido en la página 6
Connecting the Telephone Line To connect the Main Console to the telephone line, Please follow these steps: 1. Locate the two phone jacks at the top of the main console. These phone jacks are marked “ Phone “ and “ Line “. 2. Connect one end of the telephone cord that came with the system into the connector, labeled” Line”. Connect the other end of that cord into the wall jack. 3. Connect a telephone to the Main Console through the phone jack. Note: The system will only work
Resumen del contenido incluido en la página 7
Operation – Main Console The Main Console is the heart of the security system. It monitors the sensors and responds according to how it is programmed, whenever a sensor is activated. The illustration shown for the Main Console may look complex at first, however, most procedures are straightforward and easy. Please review the illustration below, which labels all the parts of the Main Console. LCD Panel Illustration 12 3 4 56 7 8 9 0 # MICROPROCESSOR CONTROL KEYPAD LEGEND 1 .
Resumen del contenido incluido en la página 8
13. Armed LED : When the light is ‘on’, the system is armed; When the light is ‘off’, the system is disarmed. 14. LCD Panel : Displays messages 15. Speaker : Sounds alarm and plays back messages 16. Antenna : Used for wireless reception 17. Output Jack : Connects to the external siren 18. Phone Jack : Connects to the phone set 19. Line Jack : Connect to the Telephone line from the wall 20. DC Power Jack : DC supply input 3.0: Function for Installer Menu – Factory Default Password
Resumen del contenido incluido en la página 9
3.1: System Option menu : Press 0 to start setting Setting : 0 – T 1 2 3 4 5 6 – P 7 – MSG 8 – DIAL 9 - CODE (1) 0-T : For time setting (Default is 30 seconds.) minimum 1 second, maximum 255 seconds. Press the 0 button, to go to the time setting (exit, alarm, entry) time Setting : Time 1 - Exit 2 – Alarm 3 - Entry Press the 1 button, to set the delay time for exiting the house. The default time is 30 Sec, You can set the
Resumen del contenido incluido en la página 10
Setting 5 : The first priority dial in case of Fire. (check with the fire dept if this is acceptable) : The first priority dial in case of Medical help. Setting 6 (check with the hospital if this is acceptable ) Note: The dialer will work with a touch tone service line only (3) 7- MSG : To set a recorded message which contains 1 segment of message for a maximum of 25 seconds. If the recorded message is less than 25 Sec,
Resumen del contenido incluido en la página 11
Press 1 to change the Install code menu. Setting : Change Code 1 – Install : 1 2 3 4 5 Press 2 to change the Master code menu. Setting : Change code 2 – Master : 1 3 5 2 4 6 3.2: Sequence Programming Menu This menu for code learning establishes a link between all sensors/other wireless devices and the main console. The main console has to learn the code for all sensors/other wireless devices and set a sequence learning order, as well as assign the
Resumen del contenido incluido en la página 12
listed below. It will automatically advance to the next sequencing learning order position. Sequential Pgming Sensor Added Sequential Pgming Trigger Sensor 02 7. If the sensor that was learnt into the main console is sending a signal during the learning mode, the main console will indicate on the LCD, as shown below and will not allow duplication. Sensor Already Exists in System 02 8. If the sensors “learned” reache
Resumen del contenido incluido en la página 13
be cleared. Press 3 to go into the clear mode. Clear Sensor 1 – Single 2 - All Press 1 , and key-in the sequence learning order number. Press ENTER , to clear the sensor. Clear Sensor 1 – Single Num: xx Clear Sensor Clear OK Num : xx Press 2 , It will display the words “Are you sure ? ”. Press ENTER to clear all learned sensors. Clear
Resumen del contenido incluido en la página 14
If the password is correct, the main console will emit a long beep sound. (LCD display shown below). Access Granted Master Mode : MASTER A-AWAY H-HOME Now the system will select the arm mode and set the system in either Away arm/Home Arm mode (see below): A - AWAY : Press the AWAY button to set the “ Armed - Away “ alert. After the exit delay the Arm LED will illuminate steady and the system is
Resumen del contenido incluido en la página 15
SP DIAL + 4 , the autodial order is: Preset 4 → Preset 1 → Preset 2 →Preset 3 (Burglary condition) SP DIAL + 5 , the autodial order is: Preset 5 → Preset 1 → Preset 2 →Preset 3 (Fire condition) SP DIAL + 6 , the autodial order is: Preset 6 → Preset 1 → Preset 2 →Preset 3 (Medical help condition) Arm or Disarm Via the Telephone Line (for Tone Mode) This function allows you to dial your home telephone from outside and remotely control/change the arm/disarm
Resumen del contenido incluido en la página 16
is answered, it will playback the message 2 times Medical help - It will automatically dial Preset 6 → Preset 1 → Preset 2 → Preset3, phone numbers for 3 cycles (6, 1, 2, 3). When the telephone is answered, it will playback the message 2 times LCD “MSG” : Message indicating on LCD This system will leave a warning message on the LCD panel when the sensors are opened, triggered or in a low battery
Resumen del contenido incluido en la página 17
Remote Control Handset The key chain Remote Control Handset is a convenient way to arm (Home / Away mode) or disarm this system. Before using this device, please program it into the main console via the sequence programming menu. DC12V LEGEND 1. TRANSMIT LED 2. DISARM KEY 3. AWAY KEY 4. HOME KEY 5. PANIC KEY 6. BATTERY 1. TRANSMIT LED : The LED will light when the device is transmitting 2. DISARM : Press this button to disarm the system or clear the message 3. AWAY
Resumen del contenido incluido en la página 18
• Press the PANIC button, to activate the “PANIC” function. The activation of the “PANIC” function will immediately trigger the alarm and auto dialer. 63 REMOTE SENSOR 01 Panic PIR Motion Detector The PIR Motion Detector is designed to detect the movement of objects in a room or hallway. The effective range of the motion sensor is 30 feet long, with an 84degree horizontal angle. Before using this sensor, please program this sensor into the main console via the
Resumen del contenido incluido en la página 19
4. BATTERY : Remove the Battery cover and insert one 9V alkaline battery. 5. ARM & HOLDER : For mounting on the wall. 6. BATTERY COVER Replace the Battery When the sensor sends a low battery message to main console, remove the old battery and replace it with a fresh alkaline battery. The LCD is shown below 63 PIR SENSOR 01 Low battery Zone Address Setting Enter the Installer password and press “1” to activate the “Sequence Programming Menu” after
Resumen del contenido incluido en la página 20
Before installing the sensor, consider the following points: Mount the sensor two meters (6-1/2’) high for best coverage. Mount the sensor with a 14 degree downward incline angle against the wall for optimum range. To install the PIR Motion Sensor, please follow these steps: Take out the screws or double sided adhesive and install the mounting bracket on the wall. Press the ball joint portion into the bracket until it snaps securely. (Secure t
