Resumen del contenido incluido en la página 1
ONYX®FIRSTVISION™
Installation and Operation Manual
Document 53034
10/29/07 Rev: A2
P/N: 53034:A2 ECN: 07-706
Resumen del contenido incluido en la página 2
Fire Alarm System Limitations While a fire alarm system may lower insurance rates, it is not a substitute for fire insurance! An automatic fire alarm system—typically made up of smoke detec- Heat detectors do not sense particles of combustion and alarm only tors, heat detectors, manual pull stations, audible warning devices, when heat on their sensors increases at a predetermined rate or and a fire alarm control panel with remote notification capability—can reaches a predetermined level. Rate
Resumen del contenido incluido en la página 3
Installation Precautions Adherence to the following will aid in problem-free installation with long-term reliability: WARNING - Several different sources of power can be connected Like all solid state electronic devices, this system may operate to the fire alarm control panel. Disconnect all sources of power erratically or can be damaged when subjected to lightning-induced before servicing. The control unit and associated equipment may be transients. Although no system is completely immune
Resumen del contenido incluido en la página 4
Documentation Feedback Your feedback helps us keep our documentation up-to-date and accurate. If you have any comments, you can email us. Please include the following information: • Product name and version number (if applicable) • Manual page number • Your comment Send email messages to: FireSystems.TechPubs@honeywell.com Please note this email address is for documentation feedback only. If you have any technical issues, please contact Technical Services. 4 FIRSTVISION™ Installation and Opera
Resumen del contenido incluido en la página 5
Table of Contents Section 1 Introduction..............................................................................................................3 1.1: FIRSTVISION Specifications ...........................................................................................................................3 Table 1.1 FIRSTVISION Cabinet Specifications ......................................................................................3 Table 1.2 FIRSTVISION LCD Specifications..................
Resumen del contenido incluido en la página 6
Table of Contents Figure 3.8 Date and Time Properties....................................................................................................21 Figure 3.9 Time Zone Tab....................................................................................................................21 3.5: Establish Communication Between Your LAN and FIRSTVISION...............................................................22 Figure 3.10 Windows LAN Connection........................................
Resumen del contenido incluido en la página 7
Section 1 Introduction The contents of this manual are important and must be kept in close proximity to the hardware. If building ownership is changed, this manual and all other testing and maintenance information must also be passed to the current owner of the facility. A copy of this manual was shipped with the equipment and is also available from the manufacturer. WARNING: Improper Installation ! Improper installation, maintenance, or lack of routine testing could result in system malfunct
Resumen del contenido incluido en la página 8
Introduction FIRSTVISION Specifications Table 1.2 FIRSTVISION LCD Specifications Part Number FIRSTVISION-LCD Product 17" Interactive Graphic Display Display: Size 17" Resolution 1280 x 1024, 75 Hz, 32 Bit colors Surface acoustic wave touchscreen USB TS controller CPU: Digital I/O (1) DO – Lock control, (3) DO – Brightness control ACPI Compliant Not required Processor Low Power VIA Fanless CPU Speed 733MHz Form factor Embedded Slots NONE REQUIRED Video Integral Serial ports (1) RS-232 USB por
Resumen del contenido incluido en la página 9
FIRSTVISION Descriptions Introduction 1.2 FIRSTVISION Descriptions 1.2.1 Product Overview FIRSTVISION uses a graphical user interface (GUI) approach to life safety monitoring for your building. The GUI's display method enables an authorized event responder (e.g. firefighter) to view an event in the context of the building's floor layouts. This allows planning of routes and methods for responding to the event. Before it can be used by an event responder, FIRSTVISION must be configured with i
Resumen del contenido incluido en la página 10
Introduction FIRSTVISION Descriptions Compatibility NOTE: FIRSTVISION1.5 (and above) must be used with gateway versions 3.x and above. FIRSTVISION is compatible with the node types listed in the following table. Table 1.3 FIRSTVISION Node Compatibility Table NOTI•FIRE•NET™ Node Type Network Board Used AFP-200 NAM AFP-300/400 NAM AFP-1010 SIB-NET AM2020 SIB-NET NFS-320 NCM-W/F NFS-640 NCM-W/F NFS2-640 NCM-W/F NFS-3030 NCM-W/F NFS2-3030 NCM-W/F Relative information about existing nodes (its devic
Resumen del contenido incluido en la página 11
FIRSTVISION Descriptions Introduction 1.2.2 Networking The following figure illustrates a possible NOTI•FIRE•NET™ network that includes FIRSTVISION. Refer to “Make Connections to FIRSTVISION” on page 15 for more information. FIRSTVISION NFN Gateway PC Ethernet (TCP/IP) NFN Gateway Network OR NFN Network FACP FACP FACP IRSTVISION Network Figure 1.1 Example F NOTE: If you are connecting FIRSTVISION to an NFN Gateway PC and plan on running the ONYXWorks Workstation software application also, t
Resumen del contenido incluido en la página 12
Introduction Agency Approvals 1.2.3 Ordering Information Please verify part numbers with your sales representative before and when you are ordering. Part Number Description FIRSTVISION-ENC Enclosure FIRSTVISION-LCD Liquid Crystal Display (LCD) 1.3 Agency Approvals FIRSTVISION has been designed to comply with standards set forth by the following regulatory agencies. Before proceeding, the installer should be familiar with the following documents: NFPA Standards • National Fire Protection Ass
Resumen del contenido incluido en la página 13
Conventions Used in this Manual Introduction 1.4 Conventions Used in this Manual 1.4.1 Notes, Cautions, and Warnings This manual contains notes, cautions, and warnings to alert the reader as follows: NOTE: Supplemental information for a topic, such as tips and references. CAUTION: Summary in bold ! Information about procedures that could cause programming errors, runtime errors, or equipment damage. WARNING: Summary in bold ! Indicates information about procedures that could cause irreversi
Resumen del contenido incluido en la página 14
Introduction Related Manuals •ONYX®FIRSTVISION™ Cabinet Installation Instructions PID - 53105 • AMPS-24/E Power Supply Manual - 51907 • NOTI•FIRE•NET™ Manual (Version 4.0 & Higher) - 51584 • NFS-320 Installation/Operation/Programming manuals - 52745/52746/52747 • NFS-640 Installation/Operation/Programming manuals - 51332/51334/51333 • NFS2-640 Installation/Operation/Programming manuals - 52741/52742/52743 • NFS-3030 Installation/Operation/Programming manuals - 51330/51344/51345 • NFS2-3030 Insta
Resumen del contenido incluido en la página 15
Section 2 FIRSTVISION Installation Instructions NOTE: You can use this information to install the FIRSTVISION enclosure (“Enclosure Installation” on page 12) and to make power supply connections to the enclosure’s control board, or you can refer to the ONYX®FIRSTVISION™ Enclosure Installation Instructions (P/N 53105). 2.1 Power Sources and Outputs Overview • Complete all mounting procedures and check all wiring before applying power. • Electrical connections include the following: • Primary P
Resumen del contenido incluido en la página 16
FIRSTVISION Installation Instructions Enclosure Installation 2.2 Enclosure Installation Refer to “LCD Installation” on page 14 if the enclosure is already installed. NOTE: You can use this information to install the FIRSTVISION enclosure and to make power supply connections to the enclosure’s control board or you can refer to the ONYX®FIRSTVISION™ Enclosure Installation Instructions (P/N 53105). Use the following information as a guideline to accomplish the installation of the FIRSTVISION en
Resumen del contenido incluido en la página 17
Enclosure Installation FIRSTVISION Installation Instructions Step 4. Route the LAN cable into the enclosure through one of the available knockouts. NOTE: The power supplies for FIRSTVISION and the gateway should use: - a common ground. - the same earth ground. Figure 2.1 FIRSTVISION Dimensions (inches) FIRSTVISION™ Installation and Operation Manual - P/N: 53034:Rev: A2 10/29/07 13
Resumen del contenido incluido en la página 18
back of LCD display back of LCD FIRSTVISION Installation Instructions LCD Installation Power Cable from LCD J1 The FIRSTVISION enclosure is factory assembled and wired to install/connect the LCD. P1 +24VDC/3A Enclosure’s Control Board Common GND Enclosure’s Control Board LCD Power Cable From Power Supply Figure 2.2 FIRSTVISION Power Wiring Diagram WARNING: Electrical Connections ! If power is applied to FIRSTVISION for testing your electrical connections, you MUST shut down FIRSTVISION’s
Resumen del contenido incluido en la página 19
Section 3 Enabling FIRSTVISION to Monitor Your Building 3.1 Process Overview The procedures documented in the section should be performed after your building’s life safety monitoring system has been customized to FIRSTVISION using the ONYX® FIRSTVISION™ Configuration Tool (refer to ONYX® FIRSTVISION™ Configuration Tool Programming Manual for information). Process Steps to Enable FIRSTVISION Step 1. "Make Connections to FIRSTVISION". Step 2. "Turn on Power to FIRSTVISION". Step 3. "Establish
Resumen del contenido incluido en la página 20
Enabling FIRSTVISION to Monitor Your Building Make Connections to FIRSTVISION . Figure 3.2 FIRSTVISION Standard Keyboard and Mouse Connections WARNING: Connector Damage Possible ! Do not attempt to close the LCD with the keyboard and mouse connected because their cables will make contact with the enclosure’s wiring tray; possibly damaging the connectors. Step 2. If not already connected; connect FIRSTVISION to your IP Network by attaching customer supplied CAT-5 ethernet cable to the LAN (Loc
