Resumen del contenido incluido en la página 1
PRELIMINARY
Hardwired/Wireless System
Hardwired/Wireless System
FA848C
FA848C
User Guide
N9939 7/00
Resumen del contenido incluido en la página 2
Table Of Contents QUICK REFERENCE..................................................................................................3 INTRODUCTION ........................................................................................................5 SYSTEM REFERENCE...............................................................................................6 TURNING THE SYSTEM ON.......................................................................................9 TURNING THE SYSTEM OFF ..
Resumen del contenido incluido en la página 3
Quick Reference TO TURN SYSTEM ON 1. Check to make sure the system is ready, The On/Off (ARM) light will light (Green READY light is lit). 2. Enter your 4-digit user code. 3. Exit through a door designated by your installer as an exit/entry door. TO TURN SYSTEM OFF 1. Enter through a door designated by your installer as an exit/entry door 2. Enter your 4-digit user code. 3. The system On (ARM) light will go out. TO TURN SYSTEM ON AND STAY INSIDE 1. Check to make sure the system is re
Resumen del contenido incluido en la página 4
Quick Reference The following table lists the “Quick Commands” available with this control. Key Description Keypads Comments # 1 Quick Arm - If system is ready All keypads Allows you to arm the system without requiring your user code. User code is always needed to disarm the system, though. Force Arm - bypasses faulted All keypads Allows you arm the system even if some zones are faulted. These # 2 zones zones will be automatically bypassed and will be unprotected. Quick Bypass - All keypads
Resumen del contenido incluido en la página 5
Introduction Congratulations on your decision to protect your home or business with the OMNI-848 security system. You have chosen a reliable, state-of-the-art security system that is remarkably easy to operate. Your system has been professionally installed by your local Security Company whose representative can explain the specifics of your system. The keypad is the input and display device for your security system. Your Security Company representative will suggest the model most appropriate for
Resumen del contenido incluido en la página 6
System Reference ZONE DESCRIPTIONS In the following table, enter a description of the area of protection for each zone. Example: Zone 1 Windows on North side of building Zone 4 Main entrance to building. Zone Description Zone Description 1 25 2 26 3 27 4 28 5 29 6 30 7 31 8 32 9 33 10 34 11 35 12 36 13 37 14 38 15 39 16 40 17 41 18 42 19 43 20 44 21 45 22 46 23 47 24 48 Entry time ________ Door __________ Exit time ________ Entry time ________ Door __________ Exit time is the same for all
Resumen del contenido incluido en la página 7
System Reference (cont) SEND-HELP ALERT All keypads are equipped with emergency-pair keys. In order to activate the alert, both keys must be pressed at the same time. The type of keypad you have installed dictates which keys you press. Your installer will show you how to activate these emergency keys. The emergency keys used for all keypads are shown below. The following SEND - HELP ALERT is programmed into my system: KEYS DESCRIPTION [#] & [Q Q] __________________________________ [7] & [9] ____
Resumen del contenido incluido en la página 8
System Reference (cont) USER CODE ASSIGNMENTS In the following table, enter the names of the individuals assigned to each user number. User Assigned To… User Assigned To… 1 33 2 34 3 35 4 36 5 37 6 38 7 39 8 40 9 41 10 42 11 43 12 44 13 45 14 46 15 47 16 48 17 49 18 50 19 51 20 52 21 53 22 54 23 55 24 56 25 57 26 58 27 59 28 60 29 61 30 62 31 63 32 64 ____ ____ USER CODE NOTE: User codes can be either 4 digits or 6 digits, depending 4-digit 6-digit on installer programming. Ask your installe
Resumen del contenido incluido en la página 9
Turning The System On IS THE SYSTEM READY? You can turn the burglar portion of your security system on and off. Before you can turn the system on, it must be “ready.” If you have a protected door open, or someone is moving in view of a motion detector, the system will not display “READY.” The system is ready if the READY light and the display shows: LCD Keypad: Fixed-Glass Keypad: LED Keypad: Ready LED lit Ready LED lit SYSTEM READY PART 1 TO TURN THE SYSTEM ON AND LEAVE Enter your user code. Th
Resumen del contenido incluido en la página 10
NOT READY and PART 1 - 10 -
Resumen del contenido incluido en la página 11
Turning The System On (cont) Determine which zone or zones are not ready, resolve the problem, and turn the system on normally. If the problem cannot be resolved, you may bypass the zone that is not ready. Bypassing should only be done if the problem on the zone cannot be resolved, OR if you intentionally wish to leave the zone off. For example, you would leave the zone off if you plan to keep the window open for ventilation. Zones that are bypassed are not protected when the system is on. See B
Resumen del contenido incluido en la página 12
NOTE: This system can be programmed by the installer for the AUTOSTAY feature which automatically bypasses interior zones if you arm the system and do not exit through a delay zone during exit time. - 12 -
Resumen del contenido incluido en la página 13
Turning The System On (cont) TO TURN THE SYSTEM ON IN INSTANT MODE In INSTANT mode, all alarm sensors including doors that normally have a delay to allow you to turn the system off will report an alarm immediately if activated. Check to make sure the system is ready. When it is ready, press: INSTANT followed by your user code. When the system has been turned on successfully, the On/Off light and the Instant light will be on, and the following will display: LCD Keypad: Fixed-Glass Keypad: LED Key
Resumen del contenido incluido en la página 14
† If the Quick Bypass feature has been enabled by the installer, do not enter the user code when unbypassing zones. - 14 -
Resumen del contenido incluido en la página 15
Turning The System Off When you turn the system off, you turn off only the burglar portion of your system; any smoke or heat detectors and panic keys will remain on. You must enter through a designated entry door and turn off the system within the time allowed. You can have different amounts of time for different entry points. See your system reference sheet for the times established for your system. To turn your system off: Enter your user code. If no alarms have taken place, the On/Off ligh
Resumen del contenido incluido en la página 16
User Codes TO ADD OR CHANGE A USER CODE Users can be added or changed directly at the keypad. Your system can have up to 64 different user codes, with each assigned to one of four authority levels and to a primary partition. The authority level determines the functions that user can perform. In addition, your system can be set up for 4-digit or 6-digit user codes. Ask your installer which type of user codes is used in your system. To add or change a user code, press the following: Master User Co
Resumen del contenido incluido en la página 17
Miscellaneous Commands SEND HELP ALERTS Your system can be programmed for 3 separate keypad Send Help alerts that would send an emergency signal to your central station. See the System Reference sheet to see which have been programmed for your system. DURESS Your system can be programmed to send an emergency signal to the central station if you are forced to enter the premises under threat. If you choose to include this feature, assign codes to users 60-64, which are dedicated to this function,
Resumen del contenido incluido en la página 18
NOTE: Temporary users (i.e. baby sitters, housekeepers, etc.) should not be shown the Bypass procedure. - 18 -
Resumen del contenido incluido en la página 19
Miscellaneous Commands (cont) QUICK EXIT Restarts exit delay time if the system is already armed. This allows someone to leave after the system has been armed, without having to disarm the system first. To restart the exit delay time, press: STAY .. TURN CHIME ON/OFF Chime is an optional feature that causes the keypad to beep when selected doors are opened while the burglary protection is off or disarmed. Only your installer can program a zone for the Chime feature, but once programmed, you can
Resumen del contenido incluido en la página 20
Miscellaneous Commands (cont) TO VIEW AUTOARM TIME To view the autoarm time for the partition to which the keypad is assigned, press: # [52] [user code with authority level 1 or 2]. AUTOARM TIME: 05:00PM (The user code is not required if so programmed by installer.) DOOR STRIKE To activate door strikes: Press # , then [57], then [Door #] If programmed, certain user codes can also be used to open a door. See your installer for door numbers. VIEW TIME To view the system time, press: # [51]. A
