Resumen del contenido incluido en la página 1
Burris Co.
311 East 8th Street
Greeley, CO 80631
970-356-1670
www.burrisoptics.com
Resumen del contenido incluido en la página 2
® XT -120 Xtreme Tactical Laser Flashlight
Resumen del contenido incluido en la página 3
CAUTIONS AND WARNINGS 1. Prior to the operation of any firearm in conjunction with the XT-120 make sure that you completely understand all safety precautions and procedures contained in the XT-120 operator’s manual as well as in the manual for your firearm. Failure to follow these precautions may result in damage to property, serious injury or death. 2. Always follow proper safety precautions with any firearm whether or not equipped with the XT-120. 3. Never point a firearm at anything you do no
Resumen del contenido incluido en la página 4
need to point directly at the subject. Light from the XT-120 can be safely pointed at a wall, ceiling or floor and the resulting reflected light will be sufficient to identify the object of interest. The XT-120’s light beam can also be adjusted for wide-angle illumination. 5. The XT-120 allows you to operate the ON/OFF switch while your finger is outside the trigger guard. Do not insert your finger inside the trigger guard until prepared to fire the weapon. 6. Before attaching or detaching the X
Resumen del contenido incluido en la página 5
8. Do not operate the XT-120 around any flammable or combustible material such as cleaning solvents, paints or gasoline. Do not operate the XT-120 in an environment which may contain flammable gasses such as evapo- rated gasoline. 9. Test the XT-120 periodically, especially after periods of non-use or prior to employment to verify that it is operating properly. 10. The XT-120 requires completely charged batteries for proper operation. Be careful when handling batteries to prevent leakage of harm
Resumen del contenido incluido en la página 6
DANGER Avoid Direct Exposure to Laser Radiation Beam Visible Laser Output Power: <5mW Wavelength: 640±40nm Class IIIa Laser Product • Do not look into the laser beam directly or through binoculars or telescopes. • Do not point the laser beam at mirror-like or reflective surfaces. • Do not shine the beam into the eyes of anyone. 4
Resumen del contenido incluido en la página 7
AVOID EXPOSURE Laser radiation is emitted from the APERTURE DANGER LASER RADIATION-AVOID DIRECT EYE EXPOSURE Max. Output-5mW, Wavelength:630 Complies with 21 CFR Chapter 1, Model: XT-120 Manufacture: Feb. 2005 Burris Company 331 East 8th Street, Greeley Colorado OFF VIS ILL VIS ILL XT-120 Warning/Aperture/Mode Label 5 AVOID EXPOSURE Laser radiation is emitted from the APERTURE
Resumen del contenido incluido en la página 8
For the location of the Laser Warning Label on the unit see the photo at left. WARNING Do not store the XT-120 with batteries installed. CAUTION Do not over turn the adjusters. 6
Resumen del contenido incluido en la página 9
7
Resumen del contenido incluido en la página 10
Mounting the XT-120 1. With your “cleared and safe” firearm in either hand, hold the XT-120 in the other hand with the bulb pointing away from your body in the same direction as the weapon muzzle. 2. Raise the XT-120 up and toward the firearm with the grooves of the XT-120 aligned with the firearm grooves. Slide the XT-120 back until the latch engages with an audible “click.” 3. Test the security of the latch by attempting to slide the XT-120 forward. It should remain secure and, if so, is safel
Resumen del contenido incluido en la página 11
Step 2 Step 1 9
Resumen del contenido incluido en la página 12
Latch Bar Dismounting the XT-120 1. Place your hand under the XT-120 with your index finger and thumb on each side of the latch bars. Squeeze the bars with the finger and thumb to disengage the latch bar from the firearm. 2. With the latch bars pressed in, slide the XT-120 forward, down and away from the weapon muzzle until clear of the grooves. CAUTION Never put your hand in front of the muzzle of the firearm. Be sure to push the XT-120 forward, down and away from the muzzle. 10
Resumen del contenido incluido en la página 13
Rocker Switch Operating the Switch The rocker switch has two positions: MOMENTARY and STEADY ON. The rocker switch is part of the backplate and you should not attempt to disassemble. MOMENTARY POSITION Rotate the rocker switch in a clockwise direction Mode to turn the light on in a MOMENTARY position. Release the rocker switch to turn the light off. STEADY-ON POSITION Rotate the rocker switch in a counter-clockwise direction until it clicks in the STEADY-ON position to turn the light on and keep
Resumen del contenido incluido en la página 14
Mode Switch: A rotary Mode Selection Switch on the XT-120 provides the option of four positions each indicated on the warning label - “OFF”, “VIS”, “ILL” and “VIS/ILL.” After activating the rocker switch, the modes are: OFF - the system will not operate VIS - only the visible laser is operable. ILL - only the white flashlight is operable. VIS/ILL - both the visible laser and white flashlight operate. CAUTION: The bulb in the XT-120 generates intense heat. When switched ON, never place the light
Resumen del contenido incluido en la página 15
ZEROING PROCEDURES Prior to using any firearm with the XT-120, be sure to read and understand all procedures and safety precautions associated with your weapon and the XT-120. Follow the proper “clearing” procedures for your firearm before attempting to mount or dismount the XT-120. When you squeeze the trigger of your firearm you should expect the weapon to fire so be absolutely certain of your target and back- ground before firing. Zeroing the XT-120 on a 25 meter range with target. 1. Set up
Resumen del contenido incluido en la página 16
4. Rotate the rocker switch to one side until it clicks “ON.” 5. While aiming through the weapon’s iron sights, adjust the visible aim point of the XT-120 with the provided adjusting (hex) tool until the aiming point of the beam is superimposed over the firearms’s iron sight aiming point (see diagram). 6. Fire three rounds into the center of the target aiming point at 25 meters. 7. Compare the impact point of the shot group with the beam’s aiming point. Laser Spot Front Iron Sight 8. Make additi
Resumen del contenido incluido en la página 17
FOCUSING Turn the bezel on the XT-120 until you have your desired focus being careful not to unscrew the bezel completely. CAUTION DO NOT place your hand in front of the firearm muzzle while turning the bezel. 15
Resumen del contenido incluido en la página 18
BULB REPLACEMENT With the XT-120 detached from the firearm, turn the bezel counterclockwise until it comes free from the retaining threads. Remove the old bulb as shown and insert a new bulb in its place. Replace the bezel by carefully pushing down and rotating the bezel clockwise making sure that threads are engaged properly to prevent stripping the threads. 16
Resumen del contenido incluido en la página 19
BATTERY Retaining REPLACEMENT Slot 1. With the XT-120 detached from the firearm, hold the unit in one hand and, with the thumb of your other hand, press down on the tab in the top center of the backplate. Tab 2. While keeping the tab depressed, pivot the backplate away from the body of the XT-120. 3. Remove the batteries by tipping the bezel upward to allow the two 3-volt Lithium CR123A batteries to slide out of their receptacle. 17
Resumen del contenido incluido en la página 20
4. Note the raised markings indicating battery orientation. Hold the XT-120 with mounting rails on top and the battery receptacle facing you. Insert a battery on the left side with the negative end first. Insert the other battery on the right side with the positive end first. 5. Place the bottom lip of the backplate into the bottom groove of the battery compartment and pivot upward until the tab engages into the retaining slot with an audible “click.” 6. Ensure proper functioning by manipulating
