Manual de instrucciones de Stiga GARDEN 8211-0202-11

Resumen del contenido incluido en la página 1

8211-0202-11

Resumen del contenido incluido en la página 2

H I G 1. 5. - + 6. 2. D 3. 7. G C 8. 4.

Resumen del contenido incluido en la página 3

13. 9. 14. 10. N M 11. 15. 16. 12.

Resumen del contenido incluido en la página 4

17. 5 2 3 6 7 1 18. 3 4 3. 19.

Resumen del contenido incluido en la página 5

GB ENGLISH 1 Shim washer 16 x 38 x 1.0 GENERAL 2 Locking nut This symbol indicates WARNING. Per- 2 Wing nut sonal injury and/or damage to property 2 Washer 8.4 x 24 x 2.0 may result if the instructions are not 1 Battery mount followed carefully. STEERING WHEEL SYMBOLS Install the wheel on the steering column with the The following symbols can be found on the ma- enclosed pin and push on the steering column chine to remind you of the care and attention that sleeve. are required during use: The sh

Resumen del contenido incluido en la página 6

GB ENGLISH Do not short circuit the battery’s termi- 4. Install the battery cables. nals. Sparks occur which can result in GRASS COLLECTOR (Accessory) fire. Do not wear metal jewellery which can come into contact with the battery Assemble the grass collector according to the sep- terminals. arate assembly instructions supplied with the grass collector. In the event of damage to the battery casing, cover, terminals or interference The ejector tube G may only be used together to the strip covering

Resumen del contenido incluido en la página 7

GB ENGLISH 1. Pedal released – forward once again. Engage the gear once again. Never drive engaged. The machine forceagearin. will move if a gear is engaged. 7. STARTER KEY Service brake not activated. Ignition lock used for starting/stopping the engine. 2. Pedal depressed halfway – There are 3 positions: forward drive disengaged, gear shifting can be performed. 1. Stop position – the engine is short- STOP Service brake not activated. circuited. The key can be removed. 3. Pedal fully depressed –

Resumen del contenido incluido en la página 8

GB ENGLISH - a switch on the gearbox Check the oil level every time before using. The - a switch in the seat mount machine should be standing on level ground. - a switch at the blade engaging lever Remove dipstick B and wipe it off. Slide it - a replaceable, electronic safety module which down completely and tighten it. controls the system Then unscrew it and pull it up again. Read off the In order to start the machine, the following are nec- oil level. Top up with oil to the “FULL“ mark, if ess

Resumen del contenido incluido en la página 9

GB ENGLISH CUTTING TIPS MAINTENANCE Before mowing the lawn, take care to remove any loose stones, toys and other hard objects. No servicing may be carried out on the engine or cutting deck unless: Locate any fixed objects before mowing a lawn -theenginehasstopped. you are unfamiliar with. Loose and/or fixed ob- -the starter key has been removed. jects can seriously damage the cutting deck. -the spark plug cable has been removed Do not cut wet grass (during or immediately after from the spark plu

Resumen del contenido incluido en la página 10

GB ENGLISH Oil type, winter: SAE 5W-30 KEEP THE ENGINE CLEAN (if this oil is not available, use SAE 10W-30). The engine is air-cooled. A blocked cooling sys- Use oil without any additives. tem can damage the engine. Do not fill with too much oil. This can cause the Clean the cylinder’s cooling fins and air intake of engine to overheat. grass and dirt every 5 hours or daily (fig. 12). This is particularly important when mowing dry grass. Check the oil level each time after filling. The lev- el sh

Resumen del contenido incluido en la página 11

GB ENGLISH If the machine is to stand on its end, the 3. Tighten screw and nut. petrol and engine oil must have been Replace the brake lining when it is worn. drained out first. BLADE 3. Set the lowest cutting height and remove the locking pin Q (fig. 14). Ensure that the blade is always sharp. This produc- es the best cutting results. 4. Remove the two rear locking pins R and the ca- bles for the switch contact on the deck (fig. 15). SHARPENING For safety reasons, the blade should not be sharp-

Resumen del contenido incluido en la página 12

Box 1006 · SE-573 28 TRANÅS www.stiga.com