Resumen del contenido incluido en la página 1
U U- -1 10 00 00 0 S Se er riie es s
1000 Channel PLL Frequency Synthesized UHF
Wireless Microphone and Instrument System
Owners Manual
nady.com
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS INTRODUCTION ................................................................................................2 SYSTEM FEATURES..........................................................................................3 OPERATING INSTRUCTIONS ..........................................................................4 U-1000, U-2000 Receiver ................................................................................5 UH-1000 Handheld Transmitter ..............................
Resumen del contenido incluido en la página 3
ACCESSORIES SYSTEM FEATURES PART NUMBER DESCRIPTION U-1000 RECEIVER (Single Channel) 3008-11 ............USB cable (included w/each Rx) and U-2000 RECEIVER (Dual Channel) 3008-10 ............Audio cable 1/4” to 1/4” mono plug (included w/each Rx) • Unsurpassed UHF performance with 120 dB dynamic range and operation up 12017-50 ..........WMC-11 Rubber mic clip for handheld wireless microphone to 500 feet line-of-sight (included w/each UH-1000) • Rugged 19” 1U rackmountabl
Resumen del contenido incluido en la página 4
BALANCED BALANCED MIC LINE MIC LINE AF OUT AF OUT DC IN 12V - 15V ANT.A ANT.B OPERATING INSTRUCTIONS SPECIFICATIONS U-1000, U-2000 Receiver Input Impedance ........................................UH-1000: 10 K Ohms For best operation, the receiver should be placed at least 1 meter above the UB-1000: 500 K Ohm (Instr.), ground and 1 meter away from a wall or metal surfaces. The transmitter should 10 K Ohms (Lav), 20 K Ohms (HM) also be at least 1 meter away from the receiver. Keep antenn
Resumen del contenido incluido en la página 5
SPECIFICATIONS OPERATING INSTRUCTIONS U-1000, U-2000 Receiver SYSTEM SPECIFICATIONS Powering the Receiver Operating Frequency Range ....................1000 channels switchable Plug the AC-DC ADAPTOR provided in the 15 VDC INPUT JACK (17) on the Freq. Synthesized......................................PLL system with frequency stability <0.005% back of the receiver. Then plug the adapter into an AC outlet. (Note: Any 15V Frequency Response ................................30 HZ-15 KHZ ±3 dB DC sou
Resumen del contenido incluido en la página 6
OPERATING INSTRUCTIONS TIPS U-1000, U-2000 Receiver • For operation with external antenna, low loss RF shielded cable should be next location. After finishing the edit hold the SET (7) button until the curser used and the length of the cable should not exceed 3m. stops blinking. • Do not place the receive antenna within 1 meter of another receiver or antenna. 4. Group and Channel (Preset) Choose the UHF-1000 operating frequency by • The receiver antenna should be kept away from any metal surface
Resumen del contenido incluido en la página 7
SYSTEM OPERATION OPERATING INSTRUCTIONS UH-1000 Handheld Microphone (Note: The UH transmitter CAP (7) must be removed before installing the USB cable.) (Note: Only one transmitter can be used with one UHF-1000 receiver. It TRANSMITTERS SETUP is not possible to use two transmitters on the same frequency and mix the Installing Batteries output of these transmitters into one wireless receiver. If you have any UH-1000 transmitters require 2 “AA “ size batteries to operate. Insert the questions, plea
Resumen del contenido incluido en la página 8
OPERATING INSTRUCTIONS SYSTEM OPERATION UH-1000 Handheld Microphone Connecting Audio Output There are two audio outputs on the back of the receiver. Mic-level balanced and Line-level unbalanced. Use shielded audio cable for the connection between the 1 receiver and the mixer. If the mixer / amp is a 1/4” phone jack, connect a cable from the 1/4” unbalanced audio output from the receiver. + The 1/4” output can be set to either mic line level using Gnd the MIC LINE SWITCH (12) If the mixer has an
Resumen del contenido incluido en la página 9
SYSTEM OPERATION OPERATING INSTRUCTIONS UH-1000 Handheld Microphone Level adjustment UB-1000 Transmitter 2. “NADY UH-1000” (can not be edited) The input level has four choices. “1” is the lowest gain, and “4” is the highest. NADY For instrument, lavalier mic, and HM-1 headset mic use the normal setting of UH-1000 3. User Name “3”. For HM-1 use setting “1”. The User Name field has 8 character spaces. Choose When ready to speak, move the audio MUTE switch to the OFF position. Adjust from upper and
Resumen del contenido incluido en la página 10
OPERATING INSTRUCTIONS SYSTEM OPERATION UH-1000 Handheld Microphone Frequency Selection The transmitter and receiver must be on the same frequency to operate 6. Sensitivity Set Level (Input level sensitivity) correctly. Use the Channel frequency, or Group and Channel menus described In input level sensitivity has four choices. “1” is lowest in the Receiver and Transmitter setup instructions. SENS SET gain, and “4” is highest gain. LEVEL [ 3 ] Instrument Connection In the Sens Set Level Menu, ho
Resumen del contenido incluido en la página 11
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS UB-1000 Bodypack Transmitter UB-1000 Bodypack Transmitter 6. Sensitivity Set Level (Input level sensitivity) TRANSMITTERS SETUP SENS SET In input level sensitivity has four choices. “1” is lowest Installing Batteries LEVEL [ 3 ] gain, and “4” is highest gain. UB-1000 transmitters require 2 “AA “ size batteries to operate. Insert the batteries according to the correct polarity as indicated. To open the battery In the Sens Set Level Menu, hold the SET
Resumen del contenido incluido en la página 12
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS UB-1000 Bodypack Transmitter UB-1000 Bodypack Transmitter 2. “NADY UB-100” (can not be edited) NADY 1 UB-1000 3. User Name The User Name field has 8 character spaces. Choose from upper and lower case alphabet, 27 special characters (including space), and 10 numbers. USER NAME In the User Name Menu, hold the SET (10) button for 3 CF: 01 - 01 seconds. The curser will blink, press the UP (11) or DOWN (12) buttons to cycle the character selection, press
