Resumen del contenido incluido en la página 1
Nokia Bluetooth Headset BH-100
7
6
9
8
10
Issue 1
Resumen del contenido incluido en la página 2
Nokia operates a policy of ongoing DECLARATION OF CONFORMITY development. Nokia reserves the right to Hereby, NOKIA CORPORATION declares make changes and improvements to any that this HS-78W product is in of the products described in this compliance with the essential document without prior notice. requirements and other relevant Under no circumstances shall Nokia be provisions of Directive 1999/5/EC. A copy responsible for any loss of data or income of the Declaration of Conformity c
Resumen del contenido incluido en la página 3
other countries. Diversion contrary to law is prohibited. Introduction The Nokia Bluetooth Headset BH- within 10 meters (30 feet) of each 100 allows you to make and receive other. Connections may be subject calls while on the move. You can to interference from obstructions, use the headset with compatible such as walls, or other electronic phones that support Bluetooth devices. wireless technology. The headset complies with the Read this user guide carefully Bluetooth Specification 2.0 + E
Resumen del contenido incluido en la página 4
Get started The headset contains the following Nokia for use with this particular enhancement. The use of any other parts shown on the title page: types may invalidate any approval or indicator light (1), power key (2), warranty and may be dangerous. microphone (3), charger connector (4), answer/end key (5), and For availability of approved enhancements, please check with your changeable earloop (6). dealer. When you disconnect the Before using the headset, you must power cord of any e
Resumen del contenido incluido en la página 5
charging. It may take a while Switch the headset on or off before charging starts. If To switch on, press and hold the charging does not start, power key until the headset beeps disconnect the charger, plug it and the green indicator light is in again, and retry. Charging the displayed. battery fully may take up to 1 To switch off, press and hold the hour and 30 minutes. power key until the headset beeps 4. When the battery is fully and the red indicator light is charged, the indica
Resumen del contenido incluido en la página 6
need to make the connection If the pairing is successful, the separately after pairing. You headset beeps and appears in the only need to pair the headset phone menu where you can view with your phone once. the currently paired Bluetooth devices. The headset is now ready for use. Basic use Place the headset on the ear Change the earloop The headset has an earloop The headset may be supplied with attached around it. To use the earloops in different colors. To headset without placing the ch
Resumen del contenido incluido en la página 7
the answer/end key twice while no To switch the call between the call is in progress. headset and a compatible phone, press and hold the answer/end key. If your phone supports voice dialing with the headset, press and hold Clear settings or reset the answer/end key when no call in To clear the pairing settings from progress, and proceed as described the headset, switch off the headset, in the user guide of your phone. and press and hold the power key To answer or end a call, press the
Resumen del contenido incluido en la página 8
Never use any charger that is Battery performance is particularly damaged. limited in temperatures well below freezing. Leaving the device in hot or cold places, such as in a closed car in Do not dispose of batteries in a fire as summer or winter conditions, will they may explode. Batteries may also reduce the capacity and lifetime of the explode if damaged. Dispose of battery. Always try to keep the battery batteries according to local between 15°C and 25°C (59°F and regulations. Please
Resumen del contenido incluido en la página 9
its normal temperature, moisture can form inside the device and damage electronic circuit boards. Do not attempt to open the device. Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device. Do not paint the device. Paint can clog the moving parts and prevent proper operation. All of the above suggestions apply equally to your device, batt
Resumen del contenido incluido en la página 10
10
