Manual de instrucciones de PAC SWI-PS

Resumen del contenido incluido en la página 1

Power
06-14-07
SWI-PS
Universal Steering Wheel Control Interface
For Pioneer and Sony Radios
with wired remote inputs. Installation Instructions
PacificAccessory Corporation
Before You Start
A. Is this product compatible with the vehicle?
• See application guide (seperate sheet) for listing of vehicles and connection information. If not, check www.pac-
audio.com for an updated list of compatible vehicles.
B. Prepare for the installation.
• If possible, install the SWI-PS while you are instal

Resumen del contenido incluido en la página 2

Wiring Connections Note: Only 3 wires will be used during installation. Only GM vehicles programmed for version #4, will use 4 wires. Step 1. Step 2. Connect the BLACK Connect the RED wire wire to ground (-). to switched +12V. Verification: Wire Verification: Wire reg- or location registers isters +12V when the a constant (-) when ignition key is turned probed. to the ACC or ON posi- tions. Step 3. Connect the appropriate interface wire (WHITE, YELLOW, ORANGE or GREEN). • Refer to the Ident

Resumen del contenido incluido en la página 3

SWI-PS SWI-PS SWI-PS SWI-PS SWI-PS SWI-PS SWI-PS 06-14-07 Programming the SWI-PS to Work With the Vehicle Step 5. Refer to The Vehicle Appication Guide. Note the INTERFACE Version Number next to the selected vehicle. Fill in the information below for quick reference. Version Number: ____________ (Write Version Number here) Step 6. The LED on the IGN Press and hold programming/ SWI-PS will light. ACC STRT mode button on SWI-PS. Turn the OFF vehicle ignition to the ON position. The LED will turn

Resumen del contenido incluido en la página 4

SWI-PS SWI-PS SWI-PS SWI-PS SWI-PS SWI-PS SWI-PS SWI-PS SWI-PS SWI-PS SWI-PS Programming the SWI-PS to Control the Head Unit IMPORTANT! Some steps of the programming instructions must be completed within a certain number of seconds following the previous step. Review the complete instruction before beginning the programming sequence. LED will flash to IGN Step 11. indicate set version ACC STRT number. Turn the vehicle ignition to OFF the ON position. If you programmed the interface for versi

Resumen del contenido incluido en la página 5

SWI-PS SWI-PS SWI-PS SWI-PS SWI-PS 06-14-07 Programming the SWI-PS to Control the Head Unit (cont.) The SWI-PS must be programmed in the specific order shown below. If a function is not needed, it may be skipped. 1. Volume Up 5. Track Down/Seek Down 9. Band 2. Volume Down 6. Source 3. Mute 7. Preset Up/Disc Up 4. Track Up/Seek Up 8. Preset Down/Disc Down Example: If you have a vehicle with only 3 functions, and you want to program Volume Up, Volume Down and Source. You will do Step 21-22 twice,

Resumen del contenido incluido en la página 6

Testing the SWI-PS Note: For Sony head units, please refer to the note below. Test each Heater function of the steering wheel controls. The VOL TEMP and FAN should work properly. When testing the audio TEMP controls, the left LED on the SWI-PS will flash indicating it is sending a command. If any function does not work, repeat the programming instructions (starting from Step 11) or refer to Troubleshooting Guide. Sony Head Units only!: If the Volume and Track/ Seek settings are reversed, you

Resumen del contenido incluido en la página 7

06-14-07 Appendix A: Known Incompatible Vehicles Vehicle Make(s) Year(s) Model(s) BMW All All with factory-activated cellular phones All with 5-volt SWC data wire at the steering column 2002-2003 5-Series w/navigation Mercedes-Benz All All vehicles Toyota All-2003 Sienna Volkswagen 2002-up All vehicles Appendix B: Resistor Kit Some vehicles have a seperate wire for each of the steering wheel buttons. Use this resistor kit for the steering wheel push buttons that do not already have a resistor n

Resumen del contenido incluido en la página 8

Troubleshooting Guide No power / won’t go into programming mode: • Check Red wire connection and fuse. Make sure INTERFACE is connected to switched +12volts, not constant +12volts. • Make sure vehicle ignition is on. The INTERFACE controls the stereo immediately without pressing any buttons on the steering wheel: • During programming, press the buttons on the steering wheel firmly until the left LED turns off. Releasing the button too early will cause the INTERFACE to send out a signal even wh