Resumen del contenido incluido en la página 1
GPSMAP 400/500 Series Installation Instructions
Your GPSMAP 400/500 series chartplotter must be properly installed according to the following instructions. You need the appropriate
fasteners, tools, and mounts listed in each section. If you experience difficulty installing the chartplotter, seek the assistance of a
professional installer, or contact Garmin Product Support.
Before installing your GPSMAP 400 or 500 series chartplotter, confirm that the package contains the items listed on the bo
Resumen del contenido incluido en la página 2
Selecting a Mounting Location Consider the following when selecting a location to mount your chartplotter: • The location provides optimal viewing as you operate your boat. • The location allows for easy access to the keypad on the chartplotter. • The location is strong enough to support the weight of the chartplotter and protect it from excessive vibration or shock. • Refer to the compass-safe distance table on page 10 to avoid interference with your magnetic compass. • The location allows roo
Resumen del contenido incluido en la página 3
Installing a Transducer Consult the chartplotter feature matrix on page 1 to determine if your chartplotter is capable of using sonar. The following transducer installation procedures are only applicable to sonar-capable chartplotters. NOTE: The following procedures contain installation instructions for the transducer included with the “s” model GPSMAP 400/500 series chartplotters. If you choose to use a different transducer, installation instructions are provided in the transducer kits. Some
Resumen del contenido incluido en la página 4
To mount the transducer on a transom: 1. Position the transducermount at theselected transom location. Makesure the transducer is parallel with the water line.Mark thecenter locations of each holeon thetransducer mount. Apply marine sealant to all screw Mount the transducer threads to prevent water from cable cover far above seeping into the transom. the waterline. The transducer should 1 extend /8 in. (. mm) below a fiberglass hull or 3 8 / in. (9.5 mm)
Resumen del contenido incluido en la página 5
6. Route the transducer cable to the GPSMAP 400/500 series chartplotter using cable ties to secure the cable to the motor shaft. Y ou can fill the forward-facing portion (except the cable tie pocket) of the transducer mount with sealant to avoid accumulating debris. NotIce: Leave some slack in the cable to avoid damage while using the trolling motor. NotIce: Avoid routing the cable close to electrical wires or other sources of electrical interference. Shoot-Thru-Hull Installation To avo
Resumen del contenido incluido en la página 6
> + + -- > Installing the Wiring Harness The chartplotter comes with a wiring harness that connects the chartplotter to power and to optional NMEA 0183 and Garmin CANet devices. If applicable, the wiring harness also connects the chartplotter to a transducer. The wiring harness does not connect to a NMEA 2000 network. For instructions on connecting to a NMEA 2000 network with compatible devices, see page 8. Wire Color Wire Function Power (10– Vdc*) Red Ground (power and NMEA 018) Black
Resumen del contenido incluido en la página 7
Connecting the Wiring Harness to a NMEA 0183 Device You can connect the GPSMAP device to other NMEA compatible equipment, such as a DSC or AIS device. Refer to the wiring diagram for connecting the chartplotter to NMEA 0183-compatible devices. + - Battery 10– Vdc* Wire color Wire function GPSMAP Fuse A 400/500 Power Red (power) Series Black (ground) Power ground NMEA 018 Chartplotter compliant device NMEA Ground Blue (out) NMEA Rx/A (+) > > Brown (in) NMEA Tx/A (+) Wiring a GPSMAP 400
Resumen del contenido incluido en la página 8
Connecting the Wiring Harness to a Garmin CANet Device If your GPSMAP 400/500 series chartplotter is Garmin CANet-compatible, it can receive sonar information from a CANet-compatible Garmin Sounder or Fishfinder device. See the chartplotter functionality matrix on page 1 to determine whether your chartplotter is CANet compatible. Using the CANet optimizes the performance of CANet-compatible devices, allowing sonar information from a sounder or fishfinder to be shared with up to two CANet compa
Resumen del contenido incluido en la página 9
Connecting Cables to the Chartplotter Use the diagrams below to help identify the connectors on the back of your GPSMAP 400/500 series chartplotter. Every possible chartplotter configuration is not represented in the diagrams, but every possible connector type is listed for identification purposes. Every connector on the back of the chartplotter may not be used for all installations. ➋ ➌ ➎ ➊ ➌ GPSMAP 421, 441, and 451 GPSMAP 430x and 440x ➊ Wiring harness ➋ NMEA 2000 ➌ External GPS ➍ an
Resumen del contenido incluido en la página 10
To test the transom mount transducer installation: 1. Begin testingthe installation ata slow speed. If the sonar appears to beworking properly , gradually increase thespeed of the boat while observingthe operation of the sonar. Ifthe sonar signalsuddenly is lost or the bottom return is severelydegraded, notethe speed at which thisoccurs. 2. Returnthe boat to the speed atwhich thesignal waslost. Make moderate turns inboth
Resumen del contenido incluido en la página 11
Sonar Power: 1 kW Transducer, 1,000 W (RMS), 8,000 W (peak to peak); (1 kW transducers are supported by the GPSMAP 525s/526s/535s/536s/545s/546s/555s/556s units only.) Dual Frequency, 500 W (RMS), 4,000 W (peak to peak); Dual Beam, 400 W (RMS), 3,200 W (peak to peak) Frequency: 50/200 kHz (dual frequency and 1 kW), 80/200 kHz (dual beam) Depth: 2,500 ft. (762 m) (1 kW), 1,500 ft (457 m) (dual frequency), 900 ft (274 m) (dual beam) - Depth capacity is dependent on water salinity, botto
Resumen del contenido incluido en la página 12
All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto, provided that such electronic or printed copy o
