Resumen del contenido incluido en la página 1
®
GPSMAP
2106/2110
& GPS 17
installation instructions
Graphic to be
replaced
Resumen del contenido incluido en la página 2
© Copyright 2006 Garmin Ltd. or its subsidiaries Garmin International, Inc. Garmin (Europe) Ltd. Garmin Corporation st nd 1200 East 151 Street, Unit 5, The Quadrangle, No. 68, Jangshu 2 Road, Olathe, Kansas 66062, U.S.A. Abbey Park Industrial Estate, Shijr, Taipei County, Taiwan Tel. 913/397.8200 or 800/800.1020 Romsey, SO51 9DL, U.K. Tel. 886/2.2642.9199 Fax 913/397.8282 Tel. 44/0870.8501241 Fax 886/2.2642.9099 Fax 44/0870.8501251 All rights reserved. Except as expressly provided herei
Resumen del contenido incluido en la página 3
INSTALLATION INSTRUCTIONS INTRODUCTION The GPSMAP 2106/2110 Multi-Function Display (MFD) and GPS 17 must be properly installed according to the following instructions for the best possible performance. To complete the installation, you need the appropriate fasteners, tools, and mounts listed in each section. These items are available at most marine dealers. Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. When drilling or cutting, always check fi
Resumen del contenido incluido en la página 4
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Surface Mounting the GPSMAP 2106/2110 Tools • Drill and drill bit • Screwdriver • Pencil • Mounting hardware (not included) NOTE: Mounting hardware (fasteners) not included. Mounting holes are 5/16" (7.9 mm) in diameter. To install the bail mount and unit: 1. Using the bail mount as a template, mark the location of the four mounting holes. Be sure to leave at least two inches of clearance behind the unit for the wiring. 2. Using an appropri
Resumen del contenido incluido en la página 5
INSTALLATION INSTRUCTIONS Flush Mounting the GPSMAP 2106/2110 Tools • Flush Mount Template • Jig saw • Masking tape • Scissors • Drill • Drill bits—1/8" (3 mm) and 3/8" (6 mm) • 1/16" (2 mm) Allen (Hex) wrench • Sockets or wrenches • Hammer • Center punch To flush mount the GPSMAP 2106/2110: Flush Mount 1. Trim the Flush Mount Template, and tape it in the location you want. 2. Using the center punch, indent the center of each mounting hole location. 3. Using an 1/8" (3 mm) drill bit, drill the
Resumen del contenido incluido en la página 6
INSTALLATION INSTRUCTIONS Installing the GPS 17 You can install flush mount or install the GPS 17 on any standard 1" O.D. (Outer ABOVE - BEST Dimension), 14 threads-per-inch marine mount. When mounting the GPS 17, the cable can be run externally, through the mounting panel, or through the center of Radar the marine mount. 3' BELOW - OK The GPS 17 connects to the 18-pin Power/Data Cable on the GPSMAP 2106/2110 and provides the GPS/WAAS signal for the unit. If two VHF Radio Antenna Radar or m
Resumen del contenido incluido en la página 7
INSTALLATION INSTRUCTIONS To attach the enclosed pole mount to the GPS 17: To mount the GPS 17 with the cable run outside the 1. Thread the cable though the pole mount. mount: 1. Place the cable in the vertical slot along the side of the base of 2. Align the tab on the mount to the notch on the GPS 17. the unit. 3. Use the enclosed screws to secure the mount to the base. 2. Screw the GPS 17 onto the mount. DO NOT overtighten the head. It is possible to over tighten the unit and cut the cabl
Resumen del contenido incluido en la página 8
INSTALLATION INSTRUCTIONS Wiring and Cables The GPSMAP 2106/2110 comes with an 18-pin Power/Data cable. For some installations, it may be necessary to drill 1.25" (31.7 mm) holes to route the connector end of the cables. Garmin rubber grommets are provided to cover the installation holes (see below). Wiring instructions are found on the following pages. If you experience difficulty installing the unit, contact an installation professional. The grommets may not be needed in some installations. T
Resumen del contenido incluido en la página 9
INSTALLATION INSTRUCTIONS CANet Wiring for the GPSMAP 2106/2110 ® CANet is a high-speed sonar network. Using the CANet interface optimizes the performance of the CANet-compatible units. CANet compatible unit device features, such as Ultrascroll™, are affected if a serial interface is used. To install the 3-Wire Connector: 1. Insert up to three wires into the 3-wire connector. Do not strip the wire insulation. Refer to the following CANet Terminator Connection diagram. 2. Use a standard pair o
Resumen del contenido incluido en la página 10
INSTALLATION INSTRUCTIONS Power/Data Cable Wiring The following pages contain several wiring diagrams. The first diagram on the next page is a simple diagram showing the GPSMAP 2106/2110 MFD using the 18-pin Power/Data wiring harness and the GPS 17. If two GPSMAP 2106/2110 units are installed and connected, only one GPS 17 antenna needs to be installed. Next are wiring diagram examples showing the GPSMAP 2106/2110 using the 18-pin Power/Data wiring harness interfacing with a variety of diffe
Resumen del contenido incluido en la página 11
FUSE � ������� � � � � � � � � � � � INSTALLATION INSTRUCTIONS GPS 17 GPS/WAAS SENSOR + - BATTERY 10-33 VOLTS DC WIRE WIRE COLOR COLOR FUSE � � � � � � 3 A 1 A RED RED (POWER) � � � � � � � � � � � � � � � � BLACK (GROUND) BLACK ORANGE YELLOW (ON) GREEN BLUE (DATA IN) � � WHITE WHITE (DATA OUT) GPSMAP 2106/2110 and GPS 17 Basic Wiring + - � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
Resumen del contenido incluido en la página 12
INSTALLATION INSTRUCTIONS GPS 17 GARMIN GARMIN GPSMAP 2106/2110 GPSMAP 2106/2110 Optional Alarm Wiring The GPSMAP 2106/2110 has an alarm circuit that can be used with a lamp, a horn, or both to alert you when the unit displays a message. The alarm circuit pulls low when the alarm sounds. The alarm does not have to be wired for the unit to function. The maximum current is 100 milliamps. A switch or relay can be used to select between visual and audible alerts. + - � � � � � � � � � � � � � � �
Resumen del contenido incluido en la página 13
INSTALLATION INSTRUCTIONS Final Wiring Connection After all the wiring is complete, plug the 18-pin harness into the center connector on the backside of the GPSMAP 2106/2110. The 5-pin port on the right side is intended for future interfacing features and does not require connection at this time. With power applied to the circuit, test the installation by pressing the POWER key on the front of the unit. See the GPSMAP 2106/2110 Owner's Manual for steps on initializing the receiver. 5-pin CAN
Resumen del contenido incluido en la página 14
INSTALLATION INSTRUCTIONS 12 GPSMAP 2106/2110 & GPS 17
Resumen del contenido incluido en la página 15
INSTALLATION INSTRUCTIONS Flush Mount Drilling Template Drill using a 11/64" (4.5 mm) drill bit Drill this 3/4" (19 mm) hole if the coax is going to be installed through the mounting panel GPSMAP 2106/2110 & GPS 17 13
Resumen del contenido incluido en la página 16
© Copyright 2006 Garmin Ltd. or its subsidiaries Garmin International, Inc. st 1200 East 151 Street, Olathe, Kansas 66062, U.S.A. Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K. Garmin Corporation nd No. 68, Jangshu 2 Road, Shijr, Taipei County, Taiwan www.garmin.com Part Number 190-00677-02 Rev. A
