Resumen del contenido incluido en la página 1
™
PLATINUM SERIES II
LP Gas Barbecues
Step-By-Step Guide
Platinum Series II
2200 LP
Platinum Series II
3400 LP
Platinum Series II
3200 LP
CANADIAN GAS ASSOCIATION
®
A P P R O V E D
NationalPROPANEGAS Association R
FOR YOUR SAFETY
1. Do not store or use gasoline or other
flammable vapors and liquids in the
THIS GAS APPLIANCE IS DESIGNED FOR
vicinity of this or any other appliance.
OUTDOOR USE ONLY.
2. An LP tank not connected for use shall
not be stored in the vicinity of this or
any other applia
Resumen del contenido incluido en la página 2
TOOLS NEEDED REMOVE BOTTOM TRAY Phillips screwdriver FROM GRILL Remove all tape from packaging. Remove bottom rack from top of packaging. Remove outer box. Pull out bottom tray from cooking box. Remove packaging material from 7/16 inch or adjustable wrench bottom tray, catch pan holder, catch pan, and drip pan. For the Platinum Series II 3400, remove the white plastic from the stainless steel. SUPPLIES NEEDED You will need a soap and water solution to check for gas leaks. (See section “Check for
Resumen del contenido incluido en la página 3
REMOVE GRILL FROM REMOVE PACKAGED PARTS LOWER PACKAGING FROM LOWER CARTON WARNING: Lifting the barbecue from the lower Left work surface packaging requires at least two people. With two people lift straight up and over lower packaging and cardboard support. Note: For the Platinum Series II 3400, make sure the front doors are securely closed before lifting. Right work surface (Platinum Series II 2200 LP only) Side burner (Platinum Series II 3200 LP and 3400 LP only) Figure 2 Note: For the Platinu
Resumen del contenido incluido en la página 4
INSTALLATION OF CATCH REINSTALLATION OF PAN INTO BOTTOM TRAY STAINLESS STEEL Hook the ends of the catch pan holder into the hole in the FLAVORIZER BARS bottom tray. Figure 3. The front of the catch pan holder Note: Remove any tape or packing material. Parts are must be on the same side as the finger grip of the shipped in place. Use these steps to check that they are bottom tray. in position. The Flavorizer bars are already in place. This step is only for reinstallation. Set the long stainless s
Resumen del contenido incluido en la página 5
REINSTALLATION OF INSTALL WARM-UP COOKING GRATES BASKET Note: The cooking grates are already in place. This Insert one end of the Warm-Up Basket into the hole in the step is only for reinstallation. right end of the lid and the other end into the slot in the left end of the lid. Figure 8. Set the cooking grates onto the ledges in the cooking box. The open "U" of the cooking grate goes down. Figure 6. Figure 8 Figure 6 INSTALLATION OF WARMING RACK Set the warming rack into the slots at the rear
Resumen del contenido incluido en la página 6
E F E F SET LP FUEL SCALE FILL LP TANK You will need: LP tank (empty). To fill, take the LP tank and filler adapter to an RV center, or look up gas-propane in the phone book for other Note - For accuracy, the fuel scale must be set with an sources of LP gas. empty tank. WARNING: We recommend that your LP tank be filled We utilize various LP tank manufacturers. Some of the at an authorized LP gas dealer by a qualified tanks we receive have differing top collar assemblies. attendant, who fills th
Resumen del contenido incluido en la página 7
GENERAL TANK INFORMATION n Do not use a damaged LP tank. Dented or rusty LP LP Tank Manufacturer tanks or LP tanks with a damaged valve may be The LP tank manufacturer is responsible for the materials, hazardous and should be replaced with a new one workmanship and performance of the tank. If the tank has immediately. a defect, malfunctions, or you have a question regarding n The joint where the hose connects to the LP tank the tank, call the tank manufacturer's customer service must be leak te
Resumen del contenido incluido en la página 8
If you have the Platinum Series II 2200, INSTALL WORK continue to step “Install Work SURFACES Surfaces” on this page. FOR THE PLATINUM SERIES II 2200 You will need...left work surface, right work surface, four 1/4-20 x 1/2 inch bolts, four nylon washers and a 7/16 If you have the Platinum Series II 3200, inch or adjustable wrench. go to step “Install Work Surface and Insert the left work surface tabs in the slots to the left of Side Burner” on page 9. the cooking box. Figure 11 (a). Slip washers
Resumen del contenido incluido en la página 9
Route the side burner hose so it will not interfere with the INSTALL WORK SURFACE scale indicator rod. AND SIDE BURNER The side burner hose is connected in the following manner: FOR THE PLATINUM SERIES II 3200 Slide back the collar of the quick disconnect on the You will need... left work surface, side burner assembly, manifold. Push the male fitting of the side burner hose four 1/4-20 x 1/2 inch bolts, four nylon washers and a into the quick disconnect, and maintain pressure. Slide 7/16 inch or
Resumen del contenido incluido en la página 10
INSTALL WORK SURFACE AND SIDE BURNER FOR THE PLATINUM SERIES II 3200 (CONTINUED) Check that the side burner is properly assembled. (c) Windshield Burner cap Burner ring (b) Grate Lugs Slots Igniter (a) electrode Figure 16 Burner head Burner base Burner orifice WARNING: Set the burner ring onto the burner head. Rotate the burner ring until the four lugs on the burner ring are seated in the four slots on the burner head. Figure 16 (b). Note: The burner head has a hole in it that fits over the ign
Resumen del contenido incluido en la página 11
Tabs (a) INSTALL WORK SURFACE (c) Tabs AND SIDE BURNER Tabs FOR THE PLATINUM SERIES II 3400 You will need... left work surface, side burner assembly, four 1/4-20 x 1/2 inch bolts, four nylon washers and a 7/16 inch or adjustable wrench. Insert the left work surface tabs in the slots to the left of the cooking box. Figure 17 (a). Slip washers on the bolts View from and insert the bolts as shown. Tighten. Figure 17 (b). left side View from right side To install side burner Note: Remove protective
Resumen del contenido incluido en la página 12
Check that the side burner is properly assembled. INSTALL WORK SURFACE AND SIDE BURNER (c) Windshield FOR THE PLATINUM SERIES II 3400 Burner cap (CONTINUED) Route the side burner hose around the tank panel so it will not interfere with scale indicator rod. The side burner hose is connected in the following manner: Burner ring Slide back the collar of the quick disconnect on the (b) manifold. Push the male fitting of the side burner hose into the quick disconnect, and maintain pressure. Slide Gra
Resumen del contenido incluido en la página 13
INSTALL BOTTOM RACK CHECK THAT ALL Place the bottom rack between the frame supports. BURNER VALVES ARE OFF Figure 22. Valves are shipped in the OFF position, but you should check to be sure. Put the knob on each valve. Check by pushing down and turning clockwise. If they do not turn, they are off. Proceed to the next step. Figure 23. Figure 22 For the Platinum Series II 3400, place the bottom rack Figure 23 under the cart between the frame supports. Lift up one end of the rack so it clears the c
Resumen del contenido incluido en la página 14
CONNECT FILLED LP TANK WARNING: Make sure that the LP tank valve is (a) closed. Close by turning clockwise. Hook the LP tank onto the fuel scale. Loosen the tank Collar lock wing nut. Swing the tank lock down. Tighten the wing nut. Figure 25. Tank lock wing Male nut fitting (b) Hose Valve handwheel close clockwise Tank valve Figure 25 Regulator Pressure Remove the tape and packaging from the hose and regulator. relief valve Route the hose so it will not interfere with the scale indicator rod. Ta
Resumen del contenido incluido en la página 15
CHECK FOR GAS LEAKS DANGER Do not use an open flame to check for WARNING gas leaks. Be sure there are no sparks or The gas connections of your Weber Gas open flames in the area while you check for Barbecue have been factory tested. We do leaks. This will result in a fire or explosion however recommend that you leak check all which can cause serious bodily injury or gas connections before operating your death and damage to property. Weber Gas Barbecue. WARNING: You should check for gas leaks ever
Resumen del contenido incluido en la página 16
(a) (b) CHECK FOR GAS LEAKS WARNING: Do not ignite burners while checking for leaks. Check for leaks by wetting the connections with the soap and water solution and watching for bubbles. If bubbles (c) form or if a bubble grows there is a leak. Check: a) Hose to manifold connection. Figure 30 (a). WARNING: If there is a leak at connection a, retighten the fitting with a wrench and recheck for leaks with soap and water solution. If a leak persists after retightening the fitting, turn OFF the gas
Resumen del contenido incluido en la página 17
REINSTALL THE CONTROL PANEL Set the control panel in place over both frame braces. (Hold the Crossover Ignition button up while setting the control panel in place.) Slip washers on Phillips screws, insert into holes as shown, and tighten. Figure 31 (a). Push on the burner control knobs. Figure 31 (b). Underside view Figure 31 of right work surface or side burner REFER TO OPERATING GUIDE BEFORE LIGHTING BARBECUE 17
Resumen del contenido incluido en la página 18
18
Resumen del contenido incluido en la página 19
Resumen del contenido incluido en la página 20